Page 1
IMPORTANT: KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE...
Page 2
Your 3D is now erected. If you wish to use your pushchair as a pram continue, if you wish to use your 3D as a pushchair Contents proceed to point 4.1. WARNING: Ensure that all First check all your parts have been supplied.
Page 3
Using your 3D as a pram (cont.) Using your 3D as a pram Flip the head support over so that it is Lift the leg supports to the upper upside down and place over the buckle position, so that they touch the bumper so that the head support is now laying bar (see point 9.1).
Page 4
The hood catches should easily bumper bar. The hood catches should easily ‘click’ into position. Lock them in ‘click’ onto the 3D. To lock, put the catch down. Position the rear elasticated hood place by pushing the securing skirt under the leg support joint.
Page 5
Using the brake Using the harness WARNING: Always use the To engage the brake, press down on either pedal. crotch strap in combination with the waist belt. A ‘click’ will be heard. To fasten the harness insert both buckle Note: Always check that your brake clips into each side of the buckle.
Page 6
Operating your leg support sides are level. Your 3D has a two position leg support for your child. Press the buttons simultaneously underneath both sides of the leg support and raise or lower to the desired position.
Page 7
The raincover is now Using your hood fitted. 11.1 Your 3D hood fits on the 3D facing both 13.3 Your 3D Pram System raincover is directions, rearwards for the pram mode designed to fit the 3D in either pram or and forwards for pushchair mode.
Page 8
It is easier 2) so it’s horizontal. Pull gently upwards without the liner in position, and we and the 3D will begin to fold. This lever would therefore recommend removing it is not a carry handle.
Page 9
The pushchair may lift off the floor during this action. 15.3 As the 3D begins to unfold, release the handle catches and immediately push down with your foot on the centre of the 15.2 main lock to erect your pushchair.
Page 10
To attach your Ventura Plus, unfasten 17.1 To detach your Ventura Plus, the fabric cover on the 3D arms. Lift the simultaneously press the buttons on catches inside the arms until they reach both sides of the car seat handle at the the stop point.
Page 11
Silver Cross. If anyone other than the owner is • Make sure children are clear born babies. going to use this product (e.g. grandparent,...
Page 12
Lubrifiez compromettre sa stabilité. un harnais supplémentaire. Ces anneaux sont Ce produit est un article Silver Cross de la régulièrement toutes les pièces mobiles. situés sur le harnais existant, à côté du point plus grande qualité. Il est conforme aux Ne transportez pas plus d’un...
Page 13
Tessuti e seduta: pulire con una spugna laterale del passeggino il rivenditore Silver Cross che si adopererà per imbevuta di acqua tiepida e sapone La seduta è compatibile solo con: comprometteranno la stabilità la risoluzione del problema.
Page 14
Este artículo es un producto de gran calidad Los pesos que se cuelguen periódicamente todas las partes móviles. de Silver Cross. Cumple las normativas BS del manillar y/o respaldo y/o Compruebe que haya total libertad de EN1466:2004 y si lo utiliza adecuadamente laterales del vehículo afectarán a...
Page 15
следите за тем, чтобы ребенок recambio diferentes a los suministrados o изделие на удалении от ребенка не приближался к ее подвижным recomendados por Silver Cross. Si este во избежание травм. деталям. producto va a ser utilizado por otras personas Не давайте ребенку...
Need help?
Do you have a question about the 3D and is the answer not in the manual?
Questions and answers