Graco HTX2030 Operation, Parts
Air spray trigger gun, requires up to 30 scfm 0.83 m3/min air, for portable spray application of water-based architectural paints and coatings, 1000/150/125 psi 7.0/1.0/0.9 mpa, 70/10/9 bar maximum working/fluid/air/ pressure absolute/recommended
Hide thumbs
Also See for HTX2030:
- Repair manual (28 pages) ,
- Instructions-parts list manual (26 pages) ,
- Instructions-parts list manual (26 pages)
Table of Contents
Advertisement
Quick Links
Operation - Parts
HTX2030
- For portable spray application of water-based architectural paints and coatings -
Model 24R054
Requires up to 30 SCFM (0.83 m
1000 psi (7.0 MPa, 70 bar) Maximum Working Pressure (Absolute)
150 psi (1.0 MPa, 10 bar) Maximum Fluid Working Pressure (Recommended)
125 psi (0.9 MPa, 9 bar) Maximum Air Working Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
™
Air Spray Trigger Gun
3
/min) air
332160B
EN
ti20644a
Advertisement
Table of Contents
Related Manuals for Graco HTX2030
Summary of Contents for Graco HTX2030
- Page 1 Operation - Parts 332160B ™ HTX2030 Air Spray Trigger Gun - For portable spray application of water-based architectural paints and coatings - Model 24R054 Requires up to 30 SCFM (0.83 m /min) air 1000 psi (7.0 MPa, 70 bar) Maximum Working Pressure (Absolute) 150 psi (1.0 MPa, 10 bar) Maximum Fluid Working Pressure (Recommended)
- Page 2 Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
- Page 3 Warnings WARNING PRESSURIZED ALUMINUM PARTS HAZARD Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or property damage. • Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents.
-
Page 4: Pressure Relief Procedure
Pressure Relief Procedure Pressure Relief Procedure Follow the Pressure Relief Procedure whenever 2. Turn on/off switch OFF and turn pressure control you see this symbol. knob fully counterclockwise. 3. Pull gun trigger to release pressure. 4. Turn prime/drain valve down to DRAIN position. Fluid from drain valve can splash in eyes or skin and cause serious injury. -
Page 5: Installation
Installation Installation 2. See page 6 for disk and nozzle recommendations. Install disk (2) and nozzle (5) on gun as shown. Tighten retaining rings (1 and 3) securely, but do not use a wrench. Setup NOTE: See sprayer Operation manual for instructions on how to start and prime sprayer. -
Page 6: Operation
Adjust Spray Pattern 4. Adjust air needle valve to achieve desired spray pat- tern. NOTE: More fluid flow = more air; Less fluid NOTE: See HTX2030 Operation manual for more flow = less air. details. 5. If the desired spray pattern cannot be achieved, try adjusting air pressure or try another spray disk and nozzle combination. -
Page 7: Helpful Hints
Helpful Hints Helpful Hints Flushing • Set engine throttle to lowest possible setting and • Flush applicator after each work session before fluid rotate pressure control knob fully clockwise for best begins to cure in applicator. pattern and spray control. •... - Page 8 Service Service This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure (page 4) when you stop spraying and before cleaning, checking, or servicing the equipment.
-
Page 9: Parts - Model 24R054, Series A
Parts - Model 24R054, Series A Parts - Model 24R054, Series A ti20647a Parts List Ref. Part Description Ref. Part Description 112779 VALVE, needle 160225 RING, retaining 188446 GUN BODY SPRAY TIP DISKS 16U434 ADAPTER, air inlet 235581 TIP, disk, spray, 3/8 in. 161274 PLUG 235579 TIP, disk, spray, 1/8 in. -
Page 10: Technical Data
Technical Data Technical Data ..HTX2030 Air Spray Trigger Gun Metric Maximum Air Working Pressure 125 psi 0.9 MPa, 9 bar Air Requirements 30 scfm (0.84 m /min) 30 scfm (0.84 m /min) Fluid Inlet Size... - Page 11 Notes Notes 332160B...
-
Page 12: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.