Download Print this page

Gossen MetraWatt LINAX 4000L Operating Instructions Manual

Continuous-line recorder

Table Of Contents

Table of Contents

Advertisement

Quick Links

Download this manual

Operating Instructions

LINAX 4000L

14081B

Continuous-Line Recorder

2/8.18

Table of Contents

Advertisement

Table of Contents

Need help?

Need help?

Do you have a question about the LINAX 4000L and is the answer not in the manual?

Questions and answers

Summary of Contents for Gossen MetraWatt LINAX 4000L

Page 1 Operating Instructions LINAX 4000L 14081B Continuous-Line Recorder 2/8.18...
Page 2: Table Of Contents
1.3 Installation ........3 line recorder LINAX 4000L is that it is transported and stored 1.4 Connection .
Page 3: Installation And Startup
Installation in switchboards (see Figure 1) 1. Insert the recorder into the switchboard from the front. The continuous-line recorder LINAX 4000L comes with: 2. At the sides of the case, slide the fasteners Be into the guide – 1 operating instructions grooves (see Figure 3).
Page 4: Connection
1.4 Connection (see Figure 4) Caution The connection between the protective conductor connection and a pro- The recorder must only be operated in installed condition. tective conductor must be made prior to all other connections. A power line connection switch of sufficient switching capacity, which permits all-pole disconnection of the recorder from the power line, must The unit can become dangerous when the protective conductor inside or be provided within reach of the mounting site.
Page 5: Chart Loading
1.5 Chart loading 1.5.1 Recording table for roll chart (see Figure 5 and Figure 6) 1. Unlock the recording table: Press the unlocking lever Eh down- wards (see Figure 5). The recording table tilts to the front. Remove the recording table. 2.
Page 6: Installing The Fiber Pen Insert
2 Operation 1.6 Installing the fiber pen insert 1. Fold the scales up. 2.1 Removing the recording chart 2. Install the fiber pen insert / print insert according to Figure 8. (see Figure 10) Figure 10 Removing the recording chart The rec.
Page 7: Changing The Chart Speed
0 % to 100 %. The setting behavior of the LINAX 4000L is linear. The revolution of the system motor is changed with the selection of the response time.
Page 8: Reconfiguration
3 Reconfiguration 6. Slide-in electronic unit. 7. Replace recording table. 3.1 Changing measuring ranges 3.2 Set zero and calibrate the upper range limit (see Figure 16) Standard version For the blue and violet channels, each two potentiometers (at the The recorder is supplied with 2 measuring range settings: left bottom) are accessible in the display and control panel.
Page 9: Replacing Scales
4 Maintenance 3.3 Replacing scales (see Figure 17) 4.1 Fuse replacement (see Figure 19) Figure 17 Replacing scales 1. Withdraw the fiber pen inserts. 2. Undo the scale screws at left. Figure 19 Replacing fuse Si 3. Slide the scales to the right and disengage them from the scale screw.
Page 10: Technical Data
5 Technical data Reference conditions 25 °C ± 1 K Ambient temperature Applied rules and standards Relative humidity 45 ... 75 % Hn ± 2 %, nominal frequency ± 2 % Auxiliary voltage A) International standards Front upright ± 2° Mounting position IEC 484 Potentiometric recorders...
Page 11: Packing
Electrical safety Connection, case and installation Test according to DIN EN 61010-1 (classification VDE 0411) Electrical connections Protection type IP 20 and/or IEC 61010-1 Screw-plug terminals for signal inputs Max. wire cross section 2 x 1 mm Protection class I Screw terminals for line connection Max.
Page 12: Returns And Environmentally Sound Disposal
7 Returns and Environmentally Sound 9 Product Support Disposal If required please contact: The instrument is a category 9 product (monitoring and control GMC-I Messtechnik GmbH instrument) in accordance with ElektroG (German electrical and Product Support Hotline Industry electronic device law). This device is subject to the RoHS direc- Phone: +49 911 8602-500 tive.