Table of Contents
Advertisement
with "INSERT" (fig. 10), then turn the handle to the right
until it is aligned in the "CLOSE" position;
6. Place a recipient under the filter holder and cappuccino
maker (A8) (fig. 11);
7. Press the button (B4) corresponding to the
12). Delivery begins;
8. When delivery is complete, turn the steam dial (A4) (fig.
13) and deliver steam for 10 seconds to rinse the steam
circuit;
9. Repeat points 7 and 8 until you have delivered at least 1
litre of water (about half the tank);
10. Extract the water tank (A17) (fig. 3), rinse and fill with fresh
clean water, taking care not to exceed the MAX level (fig. 4)
The appliance is ready for use.
Please note: We also recommend rinsing the internal circuits if the appliance is not
used for a long period.
4. ACTIVATING THE WATER SOFTENER FILTER
Certain models are fitted with a water softener filter (C6). If this
is not the case with your model, you are recommended to pur-
chase one from De'Longhi Customer Services.
To use the filter correctly, follow the instructions below.
1. Remove the filter from the packaging;
2. Turn the date indicator disk (fig. 14) until the next 2 months
of use are displayed;
Please note: The filter lasts about two months if the appliance is used normally. If
the coffee machine is left unused with the filter installed, it will last a maximum of 3
weeks.
3. To activate the filter, run tap water through the hole in the
filter (fig. 15) until water comes out of the openings at the
side for more than a minute;
4. Extract the tank (A17) (if necessary fill with water);
5. Insert the filter in the water tank and immerse it complete-
ly for about ten seconds, sloping it and pressing it lightly to
enable the air bubbles to escape (fig. 16);
6. Place the filter in the filter housing (A18) (fig. 17) and press
as far as it will go. Close the tank, then put the tank back
in the machine;
The filter is now active and the coffee machine can be used.
5. MENU SETTINGS
Please note: Once in the menu, you can modify all the menu functions as described
in the previous sections.
5.1 Coffee temperature
To change the temperature of the water used to make the coffee,
proceed as follows:
1. Press and hold the
for at least 3 seconds to access the menu. The
and
(B16) lights alternate;
2. Turn the mode selection dial (B8) to the
sition. The
light (B11) remains on steadily;
light (fig.
(B3) and
(B7) buttons together
ESPRESSO po-
3. Press the button corresponding to the desired selection as
shown in the following table:
Tasto
4. To exit the menù, press the
is left idle for about 1 minute, it exits automatically from
the settings menu and is ready for use again).
5.2 Water hardness
The
descale light (B9) comes on after a period of time es-
tablished according to water hardness. The machine can also
be programmed according to the actual hardness of the water
supply in the various regions, in which case descaling may be
required less frequently.
Proceed as follows:
1. Remove the "TOTAL HARDNESS TEST" indicator paper (C4)
from its pack.
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
4. Press and hold the
for at least 3 seconds to access the menu. The
and
(B16) lights alternate;
5. Turn the mode selector dial (B8) to the
position. The
6. Press the button corresponding to the desired selection as
shown in the following table:
Total Hardness Test result
7. To exit the menù, press the
(B15)
is left idle for about 1 minute, it exits automatically from
the settings menu and is ready for use again).
7
Temperatura
Normale
Alta
(B1) button. (If the appliance
(B3) and
(B7) buttons together
(B9) remains on steadily;
Button
(B1) button. (If the appliance
(B15)
LONG BLACK
Level
1
soft water
2
medium
water
3
hard or
very hard
water
Hide quick links:
Advertisement
Table of Contents
