Table of Contents
Advertisement
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
Your new Horizon Hobby vehicle has been designed and built with a
combination of waterproof and water-resistant components to allow
you to operate the product in many "wet conditions," including puddles,
creeks, wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely
waterproof and your vehicle should NOT be treated like a submarine.
The various electronic components used in the vehicle, such as the
Electronic Speed Control (ESC) and servo(s) are waterproof, however,
most of the mechanical components are water-resistant and should not
be submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as well
as the contacts in the electrical cables, will be susceptible to corrosion if
additional maintenance is not performed after running in wet conditions.
To maximize the long-term performance of your vehicle and to keep
the warranty intact, the procedures described in the "Wet Conditions
Maintenance" section below must be performed regularly if you choose
to run in wet conditions. If you are not willing to perform the additional
care and maintenance required, then you should not operate the vehicle
in those conditions.
CAUTION: Failure to exercise caution while using this
product and complying with the following precautions could
result in product malfunction and/or void the warranty.
General Precautions
• Read through the wet conditions maintenance procedures and make
sure that you have all the tools you will need to properly maintain
your vehicle.
• Not all batteries can be used in wet conditions. Consult the battery
manufacturer before use. Do not use Li-Po batteries in wet conditions.
• The included transmitter is not waterproof or water-resistant. If
using a different transmitter than the one included, consult your
transmitter's manual or the manufacturer before operation.
• Never operate your transmitter or vehicle where lightning may be
present.
• Do not operate your vehicle where it could come in contact with salt
water (ocean water or water on salt-covered roads), contaminated or
polluted water. Salt water is very conductive and highly corrosive, so
use caution.
Transmitter (SPMSTX200)
Frequency
Battery
Servo (SPMS603)
Power Supply
Output Torque
Operating Speed
Size
AXE MONSTER TRUCK
™
• Even minimal water contact can reduce the life of your motor if it
• Driving in wet conditions can reduce the life of the motor. The
Wet Conditions Maintenance
• Remove the battery pack(s) and dry the contacts. If you have an air
• Remove the tires/wheels from the vehicle and gently rinse the mud
• Use an air compressor or a can of compressed air to dry the vehicle
• Spray the bearings, drive train, fasteners and other metal parts with a
• Let the vehicle air dry before you store it. Water (and oil) may
• Increase the frequency of disassembly, inspection and lubrication of
SPECIFICATIONS
Electronic Speed Control (ESC) (DYNS2210)
2.4GHz
Input Voltage
AA × 4
Electric Capacity
4.8V~6V
Electric Capacity
41.66 oz (3 kg-cm)
BEC Voltage
0.23sec/60 degrees of travel
Size
55.6 × 18 × 30mm
Weight
has not been certified as water-resistant or waterproof. If the motor
becomes excessively wet, apply very light throttle until the water is
mostly removed from the motor. Running a wet motor at high speeds
may rapidly damage the motor.
additional resistance of operating in water causes excess strain.
Alter the gear ratio by using a smaller pinion or larger spur gear. This
will increase torque (and motor life) when running in mud, deeper
puddles, or any wet conditions that will increase the load on the
motor for an extended period of time.
compressor or a can of compressed air, blow out any water that may
be inside the recessed connector housing.
and dirt off with a garden hose. Avoid rinsing the bearings and
transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
and help remove any water that may have gotten into small crevices
or corners.
water-displacing light oil or lubricant. Do not spray the motor.
continue to drip for a few hours.
the following:
• Front and rear axle hub assembly bearings.
• All transmission cases, gears and differentials.
• Motor—clean with an aerosol motor cleaner and re-oil the
bushings with lightweight motor oil.
5–7 cell NiMH/2S LiPo 12T–34T
5–7 cell NiMH/2S-3S LiPo 35T–55T
12T Motor Limit
Forward 60A/360A
Reverse 30A/180A
6V
37.5 × 37.0 × 18.0mm
1.41 oz (40 g)
EN
3
Advertisement
Table of Contents
