Meter Setup - A.MENARINI GLUCOFIX TECH User Manual

5. Managing your Test Results
5.1. Reviewing past results
You can review past results stored in the memory. Your meter stores up
to 730 test results with dates, times and markers.
WARNING
Please make sure that the time and date are correct before the first
use, and adjust them if needed (§6.1). If the time and date settings
are not correct the meter will memorize the test results in the wrong
order.
1. Make sure the meter is off (to turn the meter off hold
until the screen switches off ).
2. Press for 2 seconds to turn the meter on and enter the memory
recall mode (the "mem" icon appears on the screen).
3. The most recent test result appears on the screen. The screen also
shows the date and time of the test and the corresponding markers.
4. Press
or to scroll through all the stored data.
5. Press for 3 seconds to switch the meter off.
NOTE
● If there are no results in the memory, the screen
displays "ooo".
● At the end of reviewing the individual test results,
the screen displays "ooo".
● Keep
or pressed to speed up the browsing
through the results.
5.2. Viewing results averages
You can view the result averages over the set intervals (1, 7, 14, 30, 60
or 90 days).
1. Follow steps 1 and 2 in §5.1.
2. Press to enter the average mode (the "AVG" icon appears on the
screen).
3. The 1-day average appears on the screen.
4. Press
to scroll through the averages.
5. After reviewing the 90-day average, press
recall mode (step 3 of § 5.1).
6. Hold for 3 seconds to switch the meter off.
NOTE
● If there are less than 2 results in the memory for the averaged
period, the screen displays "ooo". If there are no results, the screen
displays "ooo".
● The averaging function equalises HI results to 600 mg/dL
(33.3 mmol/L) and LO results to 20 mg/dL (1.1 mmol/L).
5.3. Data transmission
Test results stored in the GLUCOFIX® TECH meter's memory can be also
downloaded to GlucoLog® software or apps by means of either NFC,
a dedicated cable, or a Bluetooth dongle distributed by A. Menarini
Diagnostics only.
NOTE
● GlucoLog® software and apps, data cable, and Bluetooth dongles
are supplied separately. See relevant user manuals for instructions
on how to download data.
5.3.1. NFC Transmission
For data transmission by means of NFC the NFC function must be
enabled on the GLUCOFIX® TECH meter (§6.5) and an NFC equipped
device (such as a Smartphone) with GlucoLog® apps.
1. Activate the NFC transmission on the GlucoLog® app of the NFC
equipped device.
2. Bring the GLUCOFIX® TECH NFC antenna close (< 1 cm) to the antenna
in the NFC equipped device.
4
● Data will be transmitted even when the meter is switched off or in
memory recall mode.
3. Data transmission will start automatically (the GLUCOFIX® TECH meter
will turn on and the
4. When the data transmission is completed, "End" will be displayed on
the GLUCOFIX® TECH meter screen (together with the
beeper will sound once.
5. Press
● Data transmission via NFC may decrease battery life.
for 3 seconds

6. Meter Setup

i. Make sure the meter is off (to turn the meter off press
until the screen switches off ).
ii. Press
iii. Press
and press
to return to the memory
● At anytime during set up, you may either press
a test strip to perform a test. The changes made so far will be
memorized by the meter.
6.1 Date/Time setup
Use
to the next step: year, month, day, time format (12H, 24H), hour, minutes.
After confirming the minutes (by pressing
menus (step iii §6).
● Date is in the DD-MM format.
6.2 Alarm setup
You can set up to three alarms on your GLUCOFIX® TECH meter.
When the alarm reaches the set time, the meter sounds for 30 seconds.
● Press
alarm will remain set).
● Before setting the alarms please check that the time is properly set.
1. The display will show alarm 1 status (the default setting is OFF). You
can turn it on by pressing
move on to the next step.
2. Press
move on to the next step.
3. Press
and move on to the alarm 2 setting.
4. Set alarm 2 and 3 by following steps 2 to 3. After you have finished
setting all alarms, press
NOTE
blinking icon will be displayed on the screen).
for 3 seconds to switch off the meter.
WARNING
for 4 seconds to enter the setup menu.
or to scroll through the setting menus (see pictures below)
to enter each single menu
NOTE
or to select the correct value. Press
NOTE
NOTE
or insert a test strip to stop the acoustic meter alarm (the
CAUTION
or . Press
or to select the hour. Press
or to select the minutes. Press
to return to the setting menus (step iii §6).
icon), and a
for 3 seconds
to exit, or insert
to confirm and move on
) return to the setting
to confirm the selection and
to confirm the selection and
to confirm the selection