Advertisement
TO INSTALL A LUBRICANT CARTRIDGE
er handle. Exert force on the follower handle until lubricant
1) Remove head and plunger assembly from container tube.
oozes from the tube and head interface. Tighten container tube
into the head and plunger assembly.
2) To remove an empty cartridge,
pull back on the follower handle
until the follower rod is fully extended. Then, carefully release
5) Disengage
the follower rod from the follower by rotating the
the follower handle to eject the empty cartridge from the con-
follower handle. Push the follower rod into the container.
tainer tube. Pull back on the follower handle. When the follower
rod is fully extended, pull it sideways to latch the rod groove into
TO EXPEL AIR POCKETS
the keyhole slot in the container cap.
1) Unscrew the container
tube l-1/2 turns from the head and
plunger assembly.
2) Withdraw the follower rod from the container cap and engage it
with the follower by rotating the follower handle. Exert force on
the follower handle until lubricant oozes from the tube and head
interface.
3) Tighten container tube into the head end-plunger assembly. Dis-
engage
the follower rod from the follower by rotating
the
follower handle. Push the follower rod into the container.
3) Remove the caps from both ends of the cartridge and insert the
large open end of the cartridge into the container tube.
IMPORTANT
4) Loosely assemble
the head and plunger assembly to
the con-
tamer tube. Disengage the follower rod from the container cap.
Engage the follower rod with the follower by rotating the follow-
Air pockets inthe cartridge lubricant will
cause the grease gun tolose itsprime.
TO CONVERT GREASE GUN TO ALLOW FILLING
5) Loosely assemble the head and plunger assembly to the filled
FROM BULK CONTAINER
OR FILLER PUMP
container tube. Release the follower rod from the container cap
and disengage the follower rod from the follower by rotating the
1) Unscrew the container cap from the container tube. Pull on the
follower handle. Push the follower rod into the container.
Slowly
follower handle to extract
the follower and spring from the
unscrew the container tube from the head and plunger assembly
container tube.
until lubricant oozes from the interface. Tighten container tube
2) Grasp follower between
thumb
and forefinger
and flip the
follower lip from the rear to the front side.
NOTE: The follower resembles
a cup. When the grease gun is
assembled
for use with bulk lubricant,
the cup opens
toward the head assembly.
3) Reassemble
follower into container tube and position with the
follower handle so that the container cap can be tightened onto
the container tube.
into the head and plunger assembly.
TO FILL GREASE GUN WITH A FILLER PUMP
Engage the follower rod with the
follower by rotating
the follower
TO FILL GREASE GUN FROM
handle.
Insert
the grease
gun
BULK LUBRICANT CONTAINER
filler nipple into the filler pump
socket. Operate the filler pump
1)Remove head and plunger assembly from container tube.
to fill the grease gun container.
When the follower rod groove is
2) Pack lubricant into cavity of the head and plunger assembly.
exposed, the container
is fried
3) Insert the open end of the container tube into lubricant.
Slowly
(follower rod will be extended
pull the follower handle back while pushing the container tube
approximately
8 inches).
Dis-
deeper into the lubricant
to prevent
air pockets from being
engage the follower rod from the
pulled into the container tube.
follower by rotating the follower
handle.
Push the follower rod
4) When the follower rod is fully extended, pull it sideways to latch
into the container.
the rod groove into the keyhole slot in the container cap.
RETAIN THIS INFORMATION
FOR FUTURE REFERENCE
When ordering replacement parts, list: Part Number, Description, Model Number, and Series Letter.
LINCOLN ST. LOUIS provides a Distributor
Network that stocks equipment
and replacement parts.
A list of Authorized Service Departments will be furnished upon request.
Advertisement
