Keys and Menus Keys Modulation mode FM, AM, PULSE, CW, USB, LSB, IQ IF bandwidth (0.15 to 150 kHz) Manual gain control, squelch and tone function Toggle for 30 dB attenuation ON, OFF or AUTO Automatic frequency control ON, OFF Toggle for level-measuring process PEAK, AVG, FAST Writes to memory locations...
Keys and Menus Selects frequencies Selects a memory location Selects a parameter in the configuration menu Goes to a level higher in the menu tree or quits the editor The functions of softkeys F1 to F6 depend on what menu has been selected.
Keys and Menus Menus Scan with stored values RUN starts scan STOP stops scan SUPP suppresses memory location Configuration of the memory locations and the M- SCAN-RUN parameters RUN starts scan ACTIVATE activates memory location SUPP suppresses memory location DELETE clears current memory location or clears all memory locations RX <->...
Page 7
Keys and Menus Scan through frequency ranges RUN starts scan STOP stops scan SUPP suppresses frequency range Configuration of the frequency range RUN starts scan from current frequency Configuration of the suppressed frequency range SORT sorts suppressed frequency ranges DELETE deletes current line from the table DEL ALL deletes the whole table...
Page 8
Keys and Menus (option) Normal Spectrum SCAN mode, start, stop, marker frequency (stop frequency selected), squelch OFF, 60 dB Y-scaling NORM DIFF toggle key: differential or normal spectrum RUN STOP toggle key: sweep mode or listening mode (frozen spectrum) BW ZOOM toggle key: changeover to band- width-zoom mode ⊥...
Page 9
Keys and Menus (Option) Difference spectrum Squelch OFF, start, stop, marker frequency (start frequency selected), SCAN mode, 20 dB Y-scaling (Option) Spectrum display with BW ZOOM Squelch OFF, start, stop, marker frequency (start frequency selected), SCAN mode, 60 dB Y-scaling...
Page 10
Keys and Menus eceiver configuration ANT antenna number and code The following two softkeys appear only with installed software option EB200FS (Field Strength). ANT PAS K-factor table for passive antennae (eg HE200 without amplifier) ANT AKT K-factor table for active antennae (eg HE200 with amplifier) MEASURE measuring time parameter CONTIN continuous measurement of all values...
Page 11
Keys and Menus Choice of different displays DEFAULT basic display settings IF-PAN IF panorama display (option) LEVEL level measurement TONE signal tone whose pitch depends on the signal level CONFIG setting the chosen display (DEFAULT; IF- PAN; LEVEL; TONE, FRQ) MORE more menus FRQ frequency Configuration of IF spectrum...
Page 12
Keys and Menus Softkeys MIN starts the MIN-Hold process. MAX starts the MAX-Hold process. AVG starts averaging according to selection. Each time this key is pressed the averaging function AVG is started anew. The measured level values are averaged over the measuring time. CLRWRITE activates the display of the currently measured level values.
Receiver Settings Antenna Selection (via external antenna selector switch) select antenna number (0 to 99) by keys or spinwheel, eg : editing the antenna name Selecting a new character: leads back to RX-CONF...
Receiver Settings Measuring time parameters RX-CONFIG MEASURE MEASURE TIME: Measuring time: DEFAULT / 0.5 ms to 900 s IF-PAN MODE: Level evaluation in the spectrum of the IF panorama: MIN, MAX, AVG, CLRWRITE The chosen parameter is changed by means of rollkey or keyboard.
Receiver Settings AF configuration RX-CONFIG SPEAKER: Speaker status OFF, ON This switch works only for the built-in loudspeaker. The AF is always available at the headphone socket TONE: ONLY or WITH AF In the position TONE WITH AF, the audio frequency is audible additionally to the signal tone.
M-SCAN Storing the Receiver Settings Select Save key function This setting enables the Save key to use the current memory location for storing. This setting enables the Save key to use the next empty memory location for storing. This setting enables the Save key to use the next empty memory location for storing and additionally this memory location is set for M-SCAN.
Page 18
M-SCAN Choose memory location and save activates the memory function selects memory location (eg 999), alternatively stores receiver settings Recall stored settings activates the memory function selects memory location (eg 999), alternatively recalls receiver settings Delete memory location Warning: all memory locations are cleared with 'ALL'...
M-SCAN Preparation and Start of a Scan activates memory function selects memory location (eg 999), alternatively sets memory location to active Memory locations that are set on active will be used for the scan. starts scan with increasing sequence of memory locations starts scan with decreasing sequence of memory locations...
F-SCAN Preparation and Start of a Scan Change start frequency alternatively leads back to F-SCAN starts at current or start frequency in direction of higher frequency ranges starts at current or start frequency in direction of lower frequency ranges...
F-SCAN Suppressing the Frequency Ranges F-SCAN SUPP This function suppresses a frequency range. The frequency range is derived from the current frequency +/- ½ bandwidth. Editing the Suppressed Frequency Ranges Up to 100 frequency ranges can be stored and edited in the menu F-SCAN CONFIG SUPP.
F-SCAN Change start frequency Change stop frequency leads back to CONFIG and F-SCAN. Sorting of Suppressed Frequency Ranges SORT Sorts the suppressed frequency ranges according ascending frequency combines bordering ranges where appropriate.
D-SCAN Preparation of a Scan D-SCAN CONFIG Changing the Parmeters MEASURE TIME Measuring time: DEFAULT / 0.5 ms to 900 s D-SCAN SPEED Scan speed: MTIME PER CHANNEL /LOW / NORMAL / HIGH CYCLES Number of sweeps: 1 to 1000 / infinite REF LEVEL The reference level determines the largest level value to be represented...
D-SCAN Spectrum display NORM with squelch on When the squelch is set on, the squelch line is displayed at a y-position corresponding to the squelch value. Spectrum display in STOP mode STOP The current spectrum is frozen. The receiver sets the mark frequency.
Need help?
Do you have a question about the EB200 and is the answer not in the manual?
Questions and answers