Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Symbol PPT 2700 Series
Summary of Contents for Symbol PPT 2700 Series
- Page 2 Symbol reserves the right to make changes to any product to improve reliability, function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
-
Page 3: About This Guide
Q u i c k R e f e r e n c e Introduction Congratulations on your purchase of Symbol Technologies’ PPT 2700 Terminal! Its unique combination of features make this product superior for use in a wide range of applications. These features include: •... -
Page 4: Parts Of The Ppt 2700
P P T 2 7 0 0 S e r i e s Parts of the PPT 2700 Front View Scan LED Scan Trigger Exit Button Scroll Button Scroll Button Action Button Right Scan Trigger LCD (Screen) Power Button Function Button Application Buttons Left View Scan Exit Window... -
Page 5: Back View
Q u i c k R e f e r e n c e Parts of the PPT 2700 (continued) Back View Stylus IR Port Handstrap Connector Stylus Silo Microphone Speaker Reset Button Battery Compartment Lithium Ion Battery Battery Battery Door Latch Door Latch Battery... -
Page 6: Installing Batteries
P P T 2 7 0 0 S e r i e s Installing Batteries Before using your PPT 2700, you must install a lithium-ion battery. The battery fits behind the battery door on the back of the PPT 2700. To install the battery in your PPT 2700: 1. -
Page 7: Recharging The Battery
Q u i c k R e f e r e n c e Charge the battery in the terminal for about 2 1/2 hours before initial use. Recharging the Battery When battery voltage is low, a warning message appears indicating the battery needs to be recharged. -
Page 8: Using The Synchronization Cable To Recharge The Battery
P P T 2 7 0 0 S e r i e s charged after approximately 2 1/2 hours. See the PPT 2700 Cradle Quick Reference Guide (p/n 70-37807-xx) for more information. The Spare Battery Charge LED turns red to indicate charging, then green when the battery is fully charged. -
Page 9: Starting The Ppt 2700
Q u i c k R e f e r e n c e 2. Plug the power cable into a wall outlet and plug the other end into the battery charging receptacle on the side of the Synchro- nization Cable. Battery Charging Receptacle Starting the PPT 2700... -
Page 10: Calibrating The Screen
P P T 2 7 0 0 S e r i e s Calibrating the Screen The first time you start your PPT 2700 (and whenever the terminal is cold-booted) the calibration screen appears. This section describes how to calibrate your PPT 2700 so the cursor on the touch screen aligns with the tip of your stylus. -
Page 11: Using The Ppt 2700
Q u i c k R e f e r e n c e 4. Press the Action button to continue, or the Exit button to can- cel. Exit Button Action Button 5. Follow the directions on the screen. Using the PPT 2700 Using the Power Button The power button is on the lower left-hand side of the terminal. -
Page 12: Typing And Writing With The Stylus
The 2D scanning PPT 2700 terminal supports PDF417 bar code scanning. The raster pattern has multiple scanning rows to accommodate the PDF417 symbol’s multiple rows. 1. Point the scanner at the bar code and press the trigger. 2. Center the aiming pattern (a spot or slab raster, as pro-... -
Page 13: "Tall" Pdf Bar Codes
“Tall” PDF Bar Codes If the PDF417 symbol is “tall,” the vertical scan pattern may not be high enough to cover it. In this case, try a slow “up and down” scanning motion. With the... -
Page 14: Resetting Your Ppt 2700 Terminal
2 7 0 0 S e r i e s The scan beam does not have to be perfectly parallel with the top and bottom of the symbol (up to a 4 tilt will work). Resetting Your PPT 2700 Terminal If your PPT 2700 terminal stops responding to input from buttons or the screen, you must reset it. -
Page 15: Performing A Hard Reset
Q u i c k R e f e r e n c e Performing a Hard Reset A hard reset also restarts your PPT 2700 terminal, but erases all stored records and entries. Therefore, never perform a hard reset unless a soft reset does not solve your problem. -
Page 16: Maintaining The Ppt 2700
P P T 2 7 0 0 S e r i e s Maintaining the PPT 2700 For trouble-free service, observe the following general tips when using your PPT 2700: • Take care not to scratch the screen of your PPT 2700. When working with your PPT 2700, use the supplied stylus or plas- tic-tipped pens intended for use with a touch-sensitive screen. - Page 17 Q u i c k R e f e r e n c e No sound: • Check the Volume Control slider in the Volume & Sounds Properties screen (under Start/Settings) to make sure the vol- ume is not turned down. See the PPT 2700 Product Reference Guide for more information.
- Page 18 • Verify that the unit is loaded with a scanning application. See your System Administrator. • Check to be sure the bar code symbol is not defaced. • Be sure you are within proper scanning range. • Be sure the unit is programmed to accept the type of bar code you are scanning.
-
Page 19: Regulatory Information
Q u i c k R e f e r e n c e Regulatory Information Radio Frequency Interference Requirements This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the Federal Communications Commissions Rules and Regulation. -
Page 20: Laser Devices
Including Electrical Business Equipment • EN 60 825-1 (EN 60 825) - Safety of Devices Containing Lasers Laser Devices Symbol products using lasers comply with US 21CFR1040.10, and IEC825-1:1993, EN60825-1:1994+A11:1996. The laser classification is marked on one of the labels on the product. - Page 21 Q u i c k R e f e r e n c e Scanner Labeling...
-
Page 22: Battery Caution
P P T 2 7 0 0 S e r i e s In accordance with Clause 5, IEC 0825 and EN60825, the following information is provided to the user: ENGLISH HEBREW CLASS 1 CLASS 1 LASER PRODUCT CLASS 2 LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT... -
Page 23: Service Information
It shall not apply to any product (i) which has been repaired or altered unless done or approved by Symbol, (ii) which has not been maintained in accordance with any operating or handling instructions supplied by Symbol, (iii) which has been... - Page 24 Customer will pay for the replacement product in case it does not return the replaced product to Symbol within 3 days of receipt of the replacement product. The process for return and customer’s charges will be in accordance with Symbol’s Exchange Policy in effect at the time of the exchange.
Need help?
Do you have a question about the PPT 2700 Series and is the answer not in the manual?
Questions and answers