Set Commands; Request Commands - Schäfter+Kirchhoff SK1024VSD Instruction Manual

Set Commands

„
Set Operation Description
Goooo<CR> gain setting 0-24 dB
Oppp<CR> offset setting
F8<CR> output format: 8 bit output data
F10<CR> output format: 10 bit output data
F12<CR> output format: 12 bit output data
C30<CR> camera clock: 30 MHz data rate
C20<CR> camera clock: 20 MHz data rate
T0<CR> test pattern off / SCM off
T1<CR> test pattern on (turns off with power off)
T2<CR> shading correction on
T3<CR> auto program Shading Correction / SCM on
T4<CR> copy flash memory 1 to SCM
T5<CR> save SCM to flash memory 1
T6<CR> video out = SCM data
T7<CR> copy Flash Memory 2 to LUT Memory
T8<CR> save LUT Memory to Flash Memory 2
T9<CR> output data = LUT data
M0<CR> line trigger mode0: internal all lines
M1<CR> line trigger mode1: extern trigger, next
line
M2<CR> line trigger mode0: internal all lines and set
max line rate
M3<CR> Pleora sync modes
M4<CR> line trigger mode4: extern trigger and restart
M5<CR> line trigger mode5: extern SOS, all lines
Axxxx<CR> SCM address (xxxxx = A0-A1023) or
LUTM (xxxxx = A32768-A33791)
Dxxxx<CR> Memory data (xxxx = 0-4095), increment
memory address counter
Eyyyyy<CR> frames / multiframe (yyyyy = 0-32767)
EFyyyyy<CR> external frame trigger delay
(yyyyy = 0-32767 lines)
Nyyyyy<CR> lines / frame (yyyyy = 1-32767)
Wyyyyy<CR> line clock frequency
(yyyyy = 50-27000) [Hz]
WLyyyyy<CR> Window Pixel length (yyyyy =1-Line length)
WFyyyyy<CR> Window First Pixel (yyyyy = 1-Line length)
Xyyyyy<CR> exposure time (yyyyy = 10-20000) [µs]
Vyyyyy<CR> extern sync divider (yyyyy = 1-32767)
Yppp<CR> set sync control (ppp = 255)
SDXT<CR> enable DXT (decoupling of line clock
frequency and exposure time)
RDXT<CR> disable DXT (decoupling of line clock
frequency and exposure time)
SLUT<CR> enable LUT
RLUT<CR> disable LUT
SNES<CR> enable NES (no EEPROM save)
RNES<CR> disable NES (no EEPROM save)
RESET<CR> reset Memory to manufacturer default
Acknowledgement for all set commands:
0 = OK, 1 = not OK
Instruction Manual SK1024VSD © 2018-12 E
Advanced Camera Control Functions

Request Commands

„
Request Return
K<CR> SK1024VSD
R<CR> Rev. 2.35
S<CR> SNr00163
I<CR> SK1024VSD
Rev. 2.35
SNr00163
I1<CR> VCC: yyyyy
I2<CR> VDD: yyyyy
I3<CR> moo: yyyyy
I4<CR> CLo: yyyyy
I5<CR> CHi: yyyyy
I6<CR> Ga: yyyyy
I8<CR> Of: yyyyy
I19<CR> Tab: yyyyy
I20<CR> CLK: yyyyy
I21<CR> ODF: yyyyy
I22<CR> TRM: yyyyy
I23<CR> SCO: yyyyy
I24<CR> Exp: yyyyy
I25<CR> miX: yyyyy
I26<CR> LCK: yyyyy
maZ: yyyyy
I27<CR>
I28<CR> TSc: yyyyy
I29<CR> SyC: yyyyy
Lin: yyyyy
I30<CR>
I31<CR> DXT: yyyyy
I32<CR> Tmp: yyyyy
I33<CR> FSD: yyyyy
I36<CR> WPL: yyyyy
I37<CR> WFP: yyyyy
I38<CR> LUT: yyyyy
I39<CR> KST: yyyyy
LUT: Lookup Table
SCM: Shading Correction Memory
SOS: Start of Scan
Range of values:
oooo = 0 ... 1023
ppp = 0 ... 255
xxxx = 4 digits integer value as ASCII
yyyyy = 5 digits integer value as ASCII
Description
returns SK type number
returns Revision number
returns Serial number
camera identification readout
returns VCC (1=10mV)
returns VDD (1=10mV)
returns mode of operation
returns camera clock low
frequency (MHz)
returns camera clock high
frequency (MHz)
returns gain
returns offset
returns number of video
channels
returns selected clock
frequency (MHz)
returns selected output data
format
returns selected trigger mode
returns shading corr. on/off
returns exposure time
returns min. exposure time (µs)
returns line frequency (Hz)
returns max. line frequency
(Hz)
returns Sync Divider
returns Sync Control
returns Lines/Frame
returns DXT on/off
returns Video Board Temper.
returns Frame Trigger Delay
returns Window Pixel Length
returns Window First Pixel
returns LUT on/off
returns Status
25