Oki C542 Advanced Manual page 125

Item Factory
default
setting
Orientation Portrait
Edit Size Cassette size
Trapping OFF
Width / Length 210 mm (8.3
inch) or
216 mm (8.5
inch)
297 mm (11.7
inch) or
279 mm (11
inch)
• Printer Adjust
Item Factory
default
setting
Manual Timeout 60 seconds
Timeout Injob 40 seconds
Timeout Local 40 seconds
Timeout Network 90 seconds
Print Mode Without Color Toner Alarm
Jam Recovery Enable
Paper Black Setting 0
Paper Color Setting 0
Description
Sets the page orientation.
Sets the size of the printable page area if the size is not
specified with the paper edit size command from a computer.
Set trapping
Sets the width of a custom paper size.
Available range: 64 to 216 mm (2.5 to 8.5 inches)
Sets the length of a custom paper size.
Available range: 90 to 1,321 mm (3.5 to 52.0 inches)
Description
Sets for how many seconds the machine waits for paper to be
fed before cancelling a job when using the manual feeder.
Sets a time interval from when the machine stops receiving
data to when it starts a forced printing.
Sets how long each port is left opened after a job is complete.
(The network is excluded.)
Sets how long the network port is left opened after a job is
complete.
Sets whether to print the document in black and white or stop
with alarm when a color toner empty error occurs.
Sets whether to print the pages again that are not printed due
to a paper jam after the jam is cleared.
Adjusts finely if the black contrast becomes weak or blots or
lines become conspicuous when printing on plain paper.
If fine blots or lines appear, decrease the value. If the dark part
becomes light, increase the value.
Adjusts finely if the color contrast becomes weak, or blots or
lines become conspicuous when printing on plain paper.
If fine blots or lines appear, decrease the value. If the dark part
becomes light, increase the value.
Item
SMR SMR 0
Setting Setting(Black)
SMR 0
Setting(Yellow)
SMR 0
Setting(Magenta)
SMR Setting(Cyan) 0
BG Setting BG Setting(Black) 0
BG Setting(Yellow) 0
BG 0
Setting(Magenta)
BG Setting(Cyan) 0
HU Setting OFF
VL Cleaning -
Gloss Mode OFF
• Print Position Adjust
Item
Tray 1 X Adjust 0 mm
Y Adjust 0 mm
Duplex X Adjust 0 mm
Duplex Y Adjust 0 mm
Tray 2/3 X Adjust 0 mm
(Optional)
Y Adjust 0 mm
Duplex X Adjust 0 mm
Duplex Y Adjust 0 mm
MP Tray X Adjust 0 mm
Y Adjust 0 mm
Duplex X Adjust 0 mm
Duplex Y Adjust 0 mm
- 125 -
5. Operating Management/ Specifications
Factory Description
default
setting
Corrects variations in print results caused by temperature and
humidity conditions and differences in print density and
frequency. Change the setting if the print quality is uneven.
Corrects variations in print results caused by temperature and
humidity conditions and differences in print density and
frequency. Change the setting if the background is dark.
Sets the mode to remove stain generated while being left for a
long time.
Cleans the image drum.
Set this mode when vertical white lines appear on the output.
Raises the fusing temperature and prints highly glossy images.
Set to [ON] when printing highly glossy images.
Factory Description
default
setting
• X Adjust: Adjusts the position of the entire printing image
perpendicular to the direction of paper movement.
Available range: ±2.00 mm (0.25 mm increments).
• Y Adjust: Adjusts the position of the entire printing image
parallel to the direction of paper movement.
Available range: ±2.00 mm (0.25 mm increments).
• Duplex X Adjust: Adjusts the position of the image on the
back side of a duplex print perpendicular to the direction of
paper movement.
Available range: ±2.00 mm (0.25 mm increments).
• Duplex Y Adjust: Adjusts the position of the image on the
back side of a duplex print parallel to the direction of paper
movement.
Available range: ±2.00 mm (0.25 mm increments).