Allen-Bradley ControlNet 1786-RPFS Installation Instructions Manual
Modular repeater short-distance fiber module
Hide thumbs
Also See for ControlNet 1786-RPFS:
- Installation instructions manual (16 pages) ,
- Product information (6 pages)
Advertisement
Quick Links
ControlNet Modular Repeater
Short-distance Fiber Module
(Cat. No. 1786-RPFS)
Use this document as a guide when you install a ControlNet
fiber module for short distances:
To install the module, read these sections:
For this information, refer to these sections:
Installation Instructions
AB PLCs
repeater
Advertisement
Related Manuals for Allen-Bradley ControlNet 1786-RPFS
Summary of Contents for Allen-Bradley ControlNet 1786-RPFS
- Page 1 Installation Instructions ControlNet Modular Repeater Short-distance Fiber Module (Cat. No. 1786-RPFS) Use this document as a guide when you install a ControlNet repeater fiber module for short distances: To install the module, read these sections: For this information, refer to these sections: AB PLCs...
- Page 2 ControlNet Modular Repeater Short-distance Fiber Module Use this module when a short-distance (distances of 300m/984ft) fiber link is required between two ControlNet products. This fiber link provides ground isolation between nodes and is less susceptible to noisy environments. The module provides: two independent full duplex fiber channels activity LED indicators for each fiber channel The figure below identifies the components of the module:...
- Page 3 Programmable Controllers, Part 2 – Equipment Requirements and Tests. For specific information that the above norm requires, see the appropriate sections in this manual, as well as the following Allen-Bradley publications: Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Guidelines for Handling Lithium Batteries, publication AG-5.4...
- Page 4 ControlNet Modular Repeater Short-distance Fiber Module To mount the module on the DIN rail: 1. Position the module on a 35 x 7.5mm DIN rail (Allen-Bradley part number 199-DR1; 46277-3; EN 50022) at a 30 angle. 2. Hook the lip on the rear of the adapter onto the top of the DIN rail,...
- Page 5 ControlNet Modular Repeater Short-distance Fiber Module 5 3. Press the module down onto the DIN rail until flush. The locking tab should snap into position and lock the module to the DIN rail. 4. If the module does not snap into position, use a screwdriver or similar device to move the locking tab down while pressing the module flush onto the DIN rail.
- Page 6 ControlNet Modular Repeater Short-distance Fiber Module 5. Remove the protective backplane cap as shown in “Removing the Protective Caps” on page 7. 6. Once attached to the DIN rail, slide modules to the left to mate with the repeater adapter or another repeater module. ATTENTION: Make certain that the adapter and repeater modules are secured together with DIN rail anchors.
- Page 7 ControlNet Modular Repeater Short-distance Fiber Module 7 1. Remove the protective caps, Transmit and Receive, from the fiber channels that will be used. 2. Save the caps for future use. AB PLCs...
- Page 8 ControlNet Modular Repeater Short-distance Fiber Module If only one channel is wired, you can use Channel 1 or Channel 2. The zipcord uses a duplex cable. Duplex cables use a single cable that contains 2 separate fibers, one for transmit and one for receive. To wire the module: 1.
- Page 9 ControlNet Modular Repeater Short-distance Fiber Module 9 2. Hold down the latch and insert the other end of the duplex cable into another module using either Channel 1 or Channel 2 of the other module. The duplex cable is manufactured with the fiber reversed on opposite ends.
- Page 10 ControlNet Modular Repeater Short-distance Fiber Module The figure below identifies indicators on the module: The table below provides probable cause for Channel 1 and Channel 2 (individually) status indicators:...
- Page 11 ControlNet Modular Repeater Short-distance Fiber Module 11 The figure below provides mounting dimensions for the module: The table below lists publications that you may want to refer to for additional information: AB PLCs...
- Page 12 The table below provides specifications for the module: Î Î Î Î Î marked for all applicable directives Î Î Î ControlNet is a trademark of Allen-Bradley, Inc. Versalink is a trademark for Hewlett Packard. HCS is a registered trademark of SpecTran Corporation.