Environmental Protection; Technical Specifications - Metabo BS 14.4 Original Instructions Manual

turning the sleeve (2) - intermediate
settings are also possible.
= Set drilling by turning the sleeve (2) (max.
torque, without torque limitation)
To avoid overloading the motor, do not
jam the spindle.
Machines with the designation SB...:
= Set screw driving by turning the sleeve
(3)
AND
set the torque (with torque limitation) by
turning the sleeve (4) - intermediate
settings are also possible.
= Set drilling by turning the sleeve (3) (max.
torque, without torque limitation)
To avoid overloading the motor, do not
jam the spindle.
= Set impact drilling by turning the sleeve
(3) (max. torque, without torque limitation)
To avoid overloading the motor, do not
jam the spindle.
6.6 Change accessory
Opening the drill chuck:
Turn the drill chuck sleeve (1) clockwise.
Clamping the tool:
Open the drill chuck and insert the tool as far as
possible. Turn the drill chuck sleeve (1) in clockwise
direction until the tool is clamped securely. With a
soft tool shank, retightening may be required after a
short drilling period.
6.7 Switching power tool on/off, setting
speed
Press the trigger switch (8) to switch on the
machine. Press in the trigger to increase the
rotational speed.
6.8 Drill chuck with "Quick" change system
(for BS 18 Quick, BS 14.4 Quick)
Removal: See page 2, fig. A. Push the interlocking
ring forward (a) and pull off the drill chuck (b).
Mounting: Push the interlock ring forward and
move the chuck as far as the limit stop on the drill
spindle.
6.9 Drill chuck (for BS 14.4, BS 18, SB 18)
See page 2, fig. B.
Undo the locking screw. Caution left-handed
thread!
Clamp an Allen key in the chuck and strike lightly
with a rubber hammer to loosen, then unscrew.
Employ the same procedure when attaching the
chuck, except in reverse order.
7. Accessories
Only use original Metabo battery packs and Metabo
accessories.
See page 4.
Only use accessories which fulfil the requirements
and specifications listed in these operating
instructions.
A Quick clamping chuck.
B Battery packs with different capacities. Only
use battery packs with voltage suitable for your
power tool.
C Angle screwdriver attachment.
D Battery charger
E Bit holder with Quick replacement system
F Bit box
For a complete range of accessories, see
www.metabo.com or the catalogue.
8. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.

9. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Protect the environment, and do not dispose
of power tools and battery packs with house-
hold waste. Observe national regulations on
separated collection and recycling of disused
machines, packaging and accessories.
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-
circuiting (e. g. by protecting them with adhesive
tape).

10. Technical Specifications

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U = Voltage of battery pack
n = No-load speed
Tightening torque for screwing:
M = soft screwing application (wood)
A
M = hard screwing application (metal)
B
M = adjustable torque (with torque control)
C
Max. drill diameter:
D = in steel
1 max
D = in softwood
2 max
D = in masonry
3 max
s = max. impact rate
ENGLISH en
11