Advertisement
INSTALLATION
WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON RED & YELLOW OUTPUT
LEADS PRIOR TO INSTALLATION, INVERTER CONNECTOR MUST BE OPEN. DO NOT JOIN
INVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED
TO THE EMERGENCY BALLAST.
NOTE:
STEP #1
INSTALLING THE EMERGENCY BALLAST
> Disconnect AC power from the fixture. Remove the ballast channel cover and install the emergency ballast
either in the ballast channel or on top of the fixture.* Remote mounting distance must be less than half the
maximum remote mounting distance for the AC ballast. Consult AC ballast manufacturer before remote
installation.
> Depending on the type of fixture in use install emergency ballast using one of the methods illustrated below.
INSIDE BALLAST CHANNEL
Inside Ballast Channel
* For installation on top of the fixture, wire bundle covers (RMC-LP) may be required by state or local codes. These covers are available
from the manufacturer as an accessory kit and must be ordered separately. Call your local distributor or the factory for complete information.
STEP #2
INSTALLING THE ILLUMINATED TEST SWITCH
> Drill a 3/8" hole and install the test switch (e.g. through the side of a surface mounted fixture).
> Refer to the illustrations below and wire the test switch so that it removes AC power from both the
emergency ballast and the AC ballast at the same time.
> If wired correctly, the ITS indicator light should be ON when AC power is supplied to the fixture, indicating
that the emergency ballast battery is charging. After installing, mark with the "PUSH TO TEST" and
"CHARGING INDICATOR LIGHT" labels.
Fixture or
Test/Monitor Plate
Lock
Washer
Illuminated
Test Switch
Hex Nut
Drill or Punch
a 3/8" Hole
Make sure that the necessary branch circuit wiring is available. An unswitched
source of power is required. The emergency ballast must be fed from the same
branch circuit as the AC ballast.
Inside Strip Fixture
INSIDE STRIP FIxTURE
SWITCHED FIxTURE
HOT
BLK
ITS
COMMON
Violet
Black
Black
Brown
WALL SWITCH
HOT
COM
B
L
K
ITS
B
L
K
Breaking Common
2
ON TOP OF FIxTURE
WALL SWITCH
WHT/RED
E
B
M
E
A
L
R
VIOLET
VIOLET(+)
L
G
BROWN
BROWN(-)
A
E
B
S
BLACK 120V
N
A
BLACK
OR
C
T
L
ORANGE 277V
A
(CAP UNUSED LEAD)
Y
L
WHITE
C
A
WHT/BLK
S
BLACK
T
WHITE
Breaking Hot
WHT/RED
E
BLACK 120V
(CAP UNUSED LEAD)
OR
B
M
ORANGE 277V
A
E
L
R
VIOLET
VIOLET(+)
L
G
BROWN
BROWN(-)
B
A
E
A
S
N
L
C
T
A
L
Y
WHITE
C
A
WHT/BLK
S
BLACK
T
WHITE
On Top of Fixture
UNSWITCHED FIxTURE
HOT
WHT/RED
E
B
BLK
M
A
E
VIOLET
VIOLET(+)
L
R
ITS
L
G
BROWN
BROWN(-)
E
A
BLACK 120V
S
N
BLACK
OR
ORANGE 277V
T
C
(CAP UNUSED LEAD)
Y
COMMON
WHITE
WHT/BLK
BLACK
WHITE
Breaking Hot
HOT
WHT/RED
E
BLACK 120V
COM
(CAP UNUSED LEAD)
OR
B
M
ORANGE 277V
B
A
L
E
K
L
R
VIOLET
VIOLET(+)
L
G
ITS
BROWN
BROWN(-)
A
E
B
S
N
L
K
C
T
Y
WHITE
WHT/BLK
BLACK
WHITE
Breaking Common
B
A
L
A
L
C
A
S
T
B
A
L
A
L
C
A
S
T
Advertisement
