Ce Declaration Of Conformity For Machines; Warnings For The Installer - FAAC 630 Manual

CE DECLARATION OF CONFORMITY FOR MACHINES

Manufacturer: FAAC S.p.A.
Address: Via Benini,  - 40069 Zola Predosa BOLOGNA - ITALY
Barrier mod.60, 630 PLUS,mod. 642
Declares that:
• is built to be integrated into a machine or to be assembled with other machinery to create a machine under
the provisions of Directive 98/37/EEC and subsequent amendments 91/368 EEC, 93/44 EEC and 93/68 EEC;
• conforms to the essential safety requirements of the other following EEC directives:
73/23/EEC and subsequent amendment 93/68/EEC.
89/336/EEC and subsequent amendment 92/31/EEC and 93/68/EEC
Furthermore, the manufacturer declares that the machinery must not be put into service until the machine into
which it will be integrated or of which it will become a component has been identified and its conformity to the
conditions of Directive 89/392/EEC and subsequent modifications assimilated in Italian National legislation under
Presidential Decree No. 459 of 24 July 1996 has been declared.
.
Bologna, 0 June 007
1) ATTENTION! To ensure the safety of people, it is important that you read
all the following instructions. Incorrect installation or incorrect use of the
product could cause serious harm to people.
2) Carefully read the instructions before beginning to install the product.
3) Do not leave packing materials (plastic, polystyrene, etc.) within reach
of children as such materials are potential sources of danger.
4) Store these instructions for future reference.
5) This product was designed and built strictly for the use indicated in this
documentation. Any other use, not expressly indicated here, could
compromise the good condition/operation of the product and/or be
a source of danger.
6) FAAC declines all liability caused by improper use or use other than that
for which the automated system was intended.
7) Do not install the equipment in an explosive atmosphere: the presence
of inflammable gas or fumes is a serious danger to safety.
8) The mechanical parts must conform to the provisions of Standards
EN 12604 and EN 12605.
For non-EU countries, to obtain an adequate level of safety, the
Standards mentioned above must be observed, in addition to national
legal regulations.
9) FAAC is not responsible for failure to observe Good Technique in
the construction of the closing elements to be motorised, or for any
deformation that may occur during use.
10) The installation must conform to Standards EN 12453 and EN 12445.
For non-EU countries, to obtain an adequate level of safety, the
Standards mentioned above must be observed, in addition to national
legal regulations.
11) Before attempting any job on the system, cut out electrical power.
12) The mains power supply of the automated system must be fitted with
an all-pole switch with contact opening distance of 3mm or greater.
Use of a 6A thermal breaker with all-pole circuit break is
recommended.
13) Make sure that a differential switch with threshold of 0.03 A is fitted
upstream of the system.
(DIRECTIVE 98/37/EC)
The Managing Director

WARNINGS FOR THE INSTALLER

GENERAL SAFETY OBLIGATIONS
14) Make sure that the earthing system is perfectly constructed, and connect
15) The automated system is supplied with an intrinsic anti-crushing safety
16) The safety devices (EN 12978 standard) protect any danger areas
17) Use of at least one indicator-light (e.g. FAACLIGHT) is recommended
18) FAAC declines all liability as concerns safety and efficient operation of
19) For maintenance, strictly use original parts by FAAC.
20) Do not in any way modify the components of the automated
21) The installer shall supply all information concerning manual operation
22) Do not allow children or adults to stay near the product while it is
23) Keep radiocontrols or other pulse generators away from children, to
24) Transit is permitted only when the automated system is idle.
25) The user must not attempt any kind of repair or direct action whatever
26) Maintenance: check at least every 6 months the efficiency of the
27) Anything not expressly specified in these instructions is not permitted.

A. Bassi
metal parts of the means of the closure to it.
device consisting of a torque control. Nevertheless, its tripping threshold
must be checked as specified in the Standards indicated at point 10.
against mechanical movement Risks, such as crushing, dragging, and
shearing.
for every system, as well as a warning sign adequately secured to the
frame structure, in addition to the devices mentioned at point "16".
the automated system, if system components not produced by FAAC
are used.
system.
of the system in case of an emergency, and shall hand over to the user
the warnings handbook supplied with the product.
operating.
prevent the automated system from being activated involuntarily.
and contact qualified personnel only.
system, particularly the efficiency of the safety devices (including, where
foreseen, the operator thrust force) and of the release devices.