Tannoy CMS 3.0 Series Quick Start Manual page 18

34 CMS 3.0 Series
CMS 403DCe Model
Performance
Frequency response (-3 dB) (1) 110 Hz - 50 kHz BM Backcan
(1)
Frequency range (-10 dB) 80 Hz - 54 kHz BM Backcan
System sensitivity (1 W @ 1 m) (2)
Nominal Coverage Angle
Coverage Angle (1 kHz to 6 kHz)
Directivity Factor (Q)
Directivity Index (DI)
(3)
Power Handling
Average
Peak
Recommended Amplifier Power
Nominal Impedance (Lo, Z)
Rated maximum SPL
Average
Peak
Transformer Taps (via front rotary switch)
70 V 30 W (165 Ω) / 15 W (330 Ω) / 7.5 W (660 Ω) / 3.75 W (1320 Ω) / OFF & low impedance operation
100 V
Crossover
Transducers
1 x 100 mm (4.0") Dual Concentric driver,
Dual Concentric point source driver
using Omnimagnet technology
Low Frequency 35 mm (1.38") voice coil, treated multi fi ber paper pulp cone
High Frequency 20 mm (0.79") PEI dome
Physical
Enclosure
Backcan
Baffl e
Grille
Safety Features
Clamping Design Min / Max clamping range: 0.0 mm (0.0") / 20.0 mm (0.79")Recommended clamp torque: 1.5 Nm
Backcan
Blind Mount (BM) Complete with fi xed backcan
Connectors Removable locking connector with screw terminals with "loop through" facility
Compliance
Dimensions
Bezel diameter
Front of ceiling to rear of pod
Hole cutout diameter
Net Weight (ea) 3.2 kg (7.05 lbs)
Included Accessories
Optional Accessories
Packed Quantity
Notes:
1. Average over stated bandwidth. Measured in an IEC baffl e in an Anechoic Chamber
2. Unweighted pink noise input, measured at 1 metre on axis
3. Long term power handling capacity as defi ned in EIA - 426B test A full range of measurements, performance data, CLF and Ease Data for CMS 403DCe/CMS 403ICTe can be downloaded from www.tannoypro.com.
TANNOY operates a policy of continuous research and development. The introduction of new materials or manufacturing methods may introduce variations in actual performance; however, actual performance always will equal or exceed the published specifi cations, which
TANNOY reserves the right to alter without prior notice. Please verify the latest specifi cations when dealing with critical applications.
CMS 403ICTe Model
110 Hz - 22 kHz
80 Hz - 24 kHz
88 dB (1 W = 4 V for 16 Ohms)
90 degrees conical
— 120 degrees
— 5.26 averaged 1 kHz to 6 kHz
— 6.30 averaged 1 kHz to 6 kHz
40 W
160 W
80 W @ 16 Ohms
16 Ohms
104 dB
110 dB
30 W (330 Ω) / 15 W (660 Ω) / 7.5 W (1320 Ω) / OFF & low impedance operation
— 7 kHz inductively coupled
100 mm (4.00") mineral loaded polypropylene
19 mm (0.75") ICT aluminium dome
—
Refl ex loaded UL 94V-0 rated ABS
Refl ex loaded UL 94V-0 rated ABS
Steel, with weather resistant coating
Safety ring located at rear of enclosure for load bearing safety bond
—
UL-1480, UL-2043, CE
205.0 mm (8.07")
147.6 mm (5.81")
187 mm (7.36")
3.0 kg (6.61 lbs)
C-Ring, tile-bridge kit, paint mask, cut-out template, grille
Plaster (mud) ring
2
Other important information
Important information
1. Register online. Please register your new
Music Tribe equipment right after you purchase it by
visiting tannoy.com. Registering your purchase using our
simple online form helps us to process your repair claims
more quickly and effi ciently. Also, read the terms and
conditions of our warranty, if applicable.
2. Malfunction. Should your Music Tribe
Authorized Reseller not be located in your vicinity,
you may contact the Music Tribe Authorized Fulfi ller for
your country listed under "Support" at tannoy.com. Should
your country not be listed, please check if your problem
can be dealt with by our "Online Support" which may also
be found under "Support" at tannoy.com. Alternatively,
please submit an online warranty claim at behringer.com
BEFORE returning the product.
3. Power Connections. Before plugging the
unit into a power socket, please make sure you are using
the correct mains voltage for your particular model.
Faulty fuses must be replaced with fuses of the same type
and rating without exception.
Quick Start Guide 35