Tannoy CMS 3.0 Series Quick Start Manual page 17

32 CMS 3.0 Series
Performance
Frequency response (-3 dB) (1) 85 Hz - 50 kHz BM Backcan
(1)
Frequency range (-10 dB) 74 Hz - 54 kHz BM Backcan
Frequency range (-10 dB) (1) 70 Hz - 54 kHz PI Backcan
(2)
System sensitivity (1 W @ 1 m)
Nominal Coverage Angle
(3)
Power Handling
Average
Programme
Peak
Recommended Amplifier Power
Nominal Impedance (Lo, Z)
Rated maximum SPL
Average
Peak
Transformer Taps (via front rotary switch)
70 V 30 W (165 Ω) / 15 W (330 Ω) / 7.5 W (660 Ω) / 3.75 W (1320 Ω) / OFF & low impedance operation
100 V
Transducers
Dual Concentric point source driver
Low Frequency
High Frequency
Physical
Enclosure
Backcan
Baffl e
Grille
Safety Features
Clamping Design Security toggle clamp Min / Max clamping range 9.5 mm (0.37") / 60 mm (2.36") Recommended clamp torque: 1.5 Nm
Backcan Options
Blind Mount (BM) Complete with fi xed backcan
Pre Install (PI) Separate backcan for pre-installation
Cable Entry Options
3 Sets of horizontal positions 19 / 22 / 28 mm
Conduit Knockouts on PI Backcan
(0.75" / 0.87" / 1.10")
Connectors
Compliance
Dimensions
Bezel diameter
Front of ceiling to rear of backcan
BM Model: Front of ceiling to rear of backcan
BM Model: Front of ceiling to top of safety loop
PI Model: Front of ceiling surface to rear of speaker unit
PI Model: Front of accessory backcan bezel to top of
safety loop
Hole cutout diameter (all models)
Net Weight (ea)
CMS 503DC BM
CMS 503DC PI
PI Backcan
Included Accessories
Optional Accessories
Packed Quantity
Notes:
1. Average over stated bandwidth. Measured in an IEC baffl e in an Anechoic Chamber
2. Unweighted pink noise input, measured at 1 metre on axis
3. Long term power handling capacity as defi ned in EIA - 426B test
A full range of measurements, performance data, CLF and Ease Data for CMS 503DC/CMS 503DC LP can be downloaded from www.tannoypro.com.
TANNOY operates a policy of continuous research and development. The introduction of new materials or manufacturing methods may introduce variations in actual performance; however, actual performance always will equal or exceed the published specifi cations, which
TANNOY reserves the right to alter without prior notice. Please verify the latest specifi cations when dealing with critical applications.
CMS 503DC Models CMS 503DC LP Model
88 Hz - 22 kHz
77 Hz - 24 kHz
—
89 dB (1 W = 4 V for 16 Ohms)
90 degrees conical
60 W
120 W
240 W
120 W @ 16 Ohms
16 Ohms
107 dB
113 dB
30 W (330 Ω) / 15 W (660 Ω) / 7.5 W (1320 Ω) / OFF & low impedance operation
1 x 130 mm (5.0") Dual Concentric driver, using Omnimagnet technology
35 mm (1.38") voice coil, treated multi fi ber paper pulp cone
20 mm (0.79") PEI dome
Zinc plated steel
Refl ex loaded UL 94V-0 rated ABS
Steel, with weather resistant coating
Safety ring located at rear of enclosure for load bearing safety bond
—
—
Cable clamp & squeeze connector for conduit up to 22 mm
—
Removable locking connector with screw terminals with "loop through" facility
UL-1480, UL-2043, CE
205.9 mm (8.11") 274.0 mm (10.79")
— 98.6 mm (3.88")
188.0 mm (7.40") —
205.3 mm (8.08") —
133.3 mm (5.25") —
153.5 mm (6.04") —
190 mm (7.48") 253.0 mm (9.96")
— 4.7 kg (10.36 lbs)
4.3 kg (9.47 lbs) —
3.2 kg (7.05 lbs) —
1.9 kg (4.18 lbs) —
C-Ring, tile-bridge kit, paint mask, cut-out template, grille
Plaster (mud) ring, Arco grille
2
CMS 503ICT Models
Performance
Frequency response (-3 dB) (1) 85 Hz - 22 kHz BM Backcan
Frequency range (-10 dB) (1) 74 Hz - 24 kHz BM Backcan
(1)
Frequency range (-10 dB) 71 Hz - 24 kHz PI Backcan
System sensitivity (1 W @ 1 m) (2)
Nominal Coverage Angle
Coverage Angle (1 kHz to 6 kHz)
Directivity Factor (Q) 5.6 averaged 1 kHz to 6 kHz
Directivity Index (DI) 7.0 averaged 1 kHz to 6 kHz
(3)
Power Handling
Average
Programme
Peak
Recommended Amplifier Power
Nominal Impedance (Lo, Z)
Rated maximum SPL
Average
Peak
Transformer Taps (via front rotary switch)
70 V 30 W (165 Ω) / 15 W (330 Ω) / 7.5 W (660 Ω) / 3.75 W (1320 Ω) / OFF & low impedance operation
100 V
Crossover 7 kHz inductively coupled
Transducers
Low Frequency 130 mm (5.00") mineral loaded polypropylene
High Frequency ICT aluminium dome
Physical
Enclosure
Backcan
Baffl e
Grille
Safety Features
Clamping Design Security toggle clamp Min / Max clamping range 9.5 mm (0.37") / 60 mm (2.36") Recommended clamp torque: 1.5 Nm
Backcan Options
Blind Mount (BM) Complete with fi xed backcan
Pre Install (PI) Separate backcan for pre-installation
Cable Entry Options
3 Sets of horizontal positions 19 / 22 / 28 mm
Conduit Knockouts on PI Backcan
(0.75" / 0.87" / 1.10")
Connectors
Compliance
Dimensions
Bezel diameter
Front of ceiling to rear of backcan
BM Model: Front of ceiling to rear of backcan
BM Model: Front of ceiling to top of safety loop
PI Model: Front of ceiling surface to rear of speaker unit
PI Model: Front of accessory backcan bezel to top of
safety loop
Hole cutout diameter (all models)
Net Weight (ea)
CMS 503ICT BM
CMS 503ICT PI
PI Backcan
Included Accessories
Optional Accessories
Packed Quantity
Notes:
1. Average over stated bandwidth. Measured in an IEC baffl e in an Anechoic Chamber
2. Unweighted pink noise input, measured at 1 metre on axis
3. Long term power handling capacity as defi ned in EIA - 426B test
A full range of measurements, performance data, CLF and Ease Data for CMS 503ICT/CMS 503ICT LP can be downloaded from www.tannoypro.com.
TANNOY operates a policy of continuous research and development. The introduction of new materials or manufacturing methods may introduce variations in actual performance; however, actual performance always will equal or exceed the published specifi cations, which
TANNOY reserves the right to alter without prior notice. Please verify the latest specifi cations when dealing with critical applications.
Quick Start Guide
CMS 503ICT LP Model
88 Hz - 50 kHz
77 Hz - 54 kHz
—
89 dB (1 W = 4 V for 16 Ohms)
90 degrees conical
105 degrees —
—
—
50 W
100 W
200 W
100 W @ 16 Ohms
16 Ohms
106 dB
112 dB
30 W (330 Ω) / 15 W (660 Ω) / 7.5 W (1320 Ω) / OFF & low impedance operation
—
1 x 130 mm (5.0") mineral loaded polypropylene
ICT
Zinc plated steel
Refl ex loaded UL 94V-0 rated ABS
Steel, with weather resistant coating
Safety ring located at rear of enclosure for load bearing safety bond
—
—
Cable clamp & squeeze connector for conduit up to 22 mm
—
Removable locking connector with screw terminals with "loop through" facility
UL-1480, UL-2043, CE
205.9 mm (8.11") 274.0 mm (10.79")
98.6 mm (3.88")
188.5 mm (7.42") 98.6 mm (3.88")
205.8 mm (8.10") —
131.7 mm (5.19") —
153.5 mm (6.04")
190 mm (7.48") 253.0 mm (9.96")
— 4.4 kg (9.70 lbs)
3.95 kg (8.70 lbs) —
2.95 kg (6.50 lbs) —
1.9 kg (4.18 lbs) —
C-Ring, tile-bridge kit, paint mask, cut-out template, grille
Plaster (mud) ring, Arco grille
2
33