Page 1
ITEM #0883772 SARATOGA CEILING FAN MODEL #00598 UL MODEL #48-STG Español p. 16 Harbor Breeze ® is a registered trademark of LF, LLC. All Rights Reserved. ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-643-0067, 8 a.m.
TABLE OF CONTENTS WARNING Safety Information....................... 2 • Suitable for use with solid-state speed controls. • WARNING - To reduce the risk of electric shock, this fan must be installed with an isolating wall Package Contents....................... 4 control/switch. • ELECTRIC SHOCK HAZARD - To reduce the risk of electric shock, make sure the electricity Hardware Contents.......................5 has been turned off at the circuit breaker or fuse box before beginning installation.
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS 1. Determine mounting method. 4a. STANDARD DOWNROD INSTALLATION: Downrod Mount (standard or angled ceiling) Insert downrod (E) through canopy (B), canopy cover (C), and yoke cover (D). Thread wires from fan Important: lf angle mounting, check to make sure the motor assembly through downrod (E).
Page 5
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS 6. Install hanger ball on top of downrod (E) into 9. Slide canopy (B) up against ceiling and over two mounting bracket (A) opening. Rotate fan until slot on screws on mounting bracket (A). Rotate canopy (B) hanger ball engages the tab on mounting bracket (A).
Page 6
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS 12. Insert blade assembly through slot on fan motor 15. Place the fitter plate (I) over two screws and turn assembly (H) and align two screw holes in blade clockwise until it locks. Install previously removed arm (F) with screw holes in fan motor assembly (H).
ASSEMBLY INSTRUCTIONS OPERATING INSTRUCTIONS REMOTE CONTROL: 18. Align the notches on the light fixture (J) with raised areas inside the fitter plate (I). NOTE: If you have more than one remote-controlled fan installed in the same location, you may want to change the frequency of the remote control to avoid any possible interference between remote controls.
CARE AND MAINTENANCE WARRANTY • IMPORTANT: Shut off main power supply before beginning any maintenance. The manufacturer warrants this fan to be free from defects in workmanship and material present at • DO NOT use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly time of shipment from the factory for lifetime limited from the date of purchase.
Page 9
ARTÍCULO # 0883772 VENTILADOR DE TECHO SARATOGA MODELO # 00598 Harbor Breeze ® es una marca registrada de LF, LLC. MODELO UL # 48-STG Todos los derechos reservados. ADJUNTE SU RECIBO AQUÍ Número de serie Fecha de compra ¿Preguntas, problemas, piezas faltantes? Antes de volver a la tienda, llame a nuestro Departamento de Servicio al Cliente al 1-800-643-0067, de lunes a jueves, de 8 a.
Page 10
ÍNDICE ADVERTENCIA Información de seguridad....................17 • Adecuado para usar con controles de velocidad de estado sólido • ADVERTANCIA: Para reducir el riesgo de descargas eléctricas, este ventilador debe instalarse con un Contenido del paquete....................... 19 interruptor de control de aislamiento de pared. •...
Page 11
CONTENIDO DEL PAQUETE ADITAMENTOS (se muestran en tamaño real) Conector de cables Tornillo para el brazo de Cant. 3 + 1 adicional las aspas con arandela Cant. 10 + 1 adicional Tuerca decorativa Tornillo para aspa Cant. 15 Cant. 15 + 1 adicional PIEZA DESCRIPCIÓN CANTIDAD...
Page 12
INSTRUCCIONES DE ENSAMBLAJE INSTRUCCIONES DE ENSAMBLAJE Determine el método de instalación. 4a. INSTALACIÓN DE LA VARILLA ESTÁNDAR: Montaje de varilla (techos estándar o en ángulo) Inserte la varilla (E) por la base (B), la cubierta de la base (C) y la cubierta de la horquilla (D). Pase los Importante: Si realiza la instalación en ángulo, cables desde el ensamble del motor del ventilador verifique que el ángulo del techo no tenga una...
Page 13
INSTRUCCIONES DE ENSAMBLAJE INSTRUCCIONES DE ENSAMBLAJE 6. Instale la bola para colgar en la parte superior de la varilla (E) 9. Deslice la base (B) contra el techo y por los dos en la abertura del soporte de montaje (A). Gire el ventilador tornillos en el soporte de montaje (A).
Page 14
INSTRUCCIONES DE ENSAMBLAJE INSTRUCCIONES DE ENSAMBLAJE 12. Inserte el ensamble del aspa a través de la ranura en 15. Coloque la placa de soporte (I) sobre los dos el ensamble del motor del ventilador (H) y alinee los tornillos y gírela en dirección de las manecillas dos orificios para tornillos en el brazo del aspa (F) con del reloj hasta que se bloquee.
Page 15
INSTRUCCIONES DE ENSAMBLAJE INSTRUCCIONES DE FUNCIONAMIENTO CONTROL REMOTO: 18. Alinee las muescas en la lámpara (J) con las áreas elevadas en el interior de la placa de soporte (I). NOTA: si tiene más de un ventilador operado por control remoto instalado en la misma ubicación, se recomienda cambiar la frecuencia del control remoto para evitar posibles interferencias entre los controles remotos.
Page 16
CUIDADO Y MANTENIMIENTO GARANTÍA • IMPORTANTE: Antes de realizar cualquier trabajo de mantenimiento, desconecte el suministro El fabricante garantiza que este ventilador no presenta defectos de fabricación ni en los materiales de electricidad principal. presentes en el momento del transporte desde la fábrica, durante un período limitado de por vida a partir de la fecha de compra.
Need help?
Do you have a question about the SARATOGA and is the answer not in the manual?
Questions and answers