Viega 8315.1 Instructions For Use Manual
Hide thumbs Also See for 8315.1:

Advertisement

Quick Links

Flush plate Visign for Style 10
Instructions for Use
for concealed cistern 2H, concealed cistern 2L, concealed cis-
tern 2C, concealed cistern Standard 2S
Model
8315.1
en_INT
Year built:
from 07/2007

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 8315.1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Viega 8315.1

  • Page 1 Flush plate Visign for Style 10 Instructions for Use for concealed cistern 2H, concealed cistern 2L, concealed cis- tern 2C, concealed cistern Standard 2S Model Year built: 8315.1 from 07/2007 en_INT...
  • Page 2 Flush plate Visign for Style 10 2 from 20...
  • Page 3: Table Of Contents

    Table of contents Table of contents About these instructions for use Target groups Labelling of notes About this translated version Product information Intended use 2.1.1 Areas of use Product description 2.2.1 Overview 2.2.2 Technical data Handling Assembly information 3.1.1 Required material and tools Assembly 3.2.1 Prepare cistern...
  • Page 4: About These Instructions For Use

    This restriction does not extend to possible operating instructions. The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
  • Page 5: About This Translated Version

    About these instructions for use About this translated version This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e.
  • Page 6: Product Information

    2 Product information Intended use 2.1.1 Areas of use Suitable cisterns The flush plate is intended for the actuation of flushes on Viega con- cealed cisterns. Installation is only possible in the following Viega concealed cisterns: Cistern model 2H Cistern model 2L Ascertain which model is installed before mounting.
  • Page 7: Product Description

    Product information Product description 2.2.1 Overview Fig. 1: Component overview 1 - flush plate 2 - support 3 - basic panel 4 - actuating rod 5 - threaded bolt 2.2.2 Technical data The product exhibits the following technical data: Flush volume The flush volume for the flushes are: Small flush volume: approx.
  • Page 8: Handling

    Handling 3 Handling Assembly information 3.1.1 Required material and tools Tool The following tools are required for mounting: flat screwdriver knife (cutter) Assembly 3.2.1 Prepare cistern The following work stages and diagrams differ depending on the cistern being used. The relevant steps are marked accordingly.
  • Page 9 Handling Score the revision shaft along the edge of the tiles with a knife. Angle the knife to do this so that the cut is made flush to the surface of the wall. Cut the corners of the revision shaft vertically through to the wall surface.
  • Page 10 Handling INFO! Only for assembly of the flush plate in cistern 2H or on the front of cistern 2L. Press the bow backwards from the mounting of the mechanism. INFO! Only for assembly of the flush plate on the top of cistern Press the bow backwards from the mounting of the mechanism.
  • Page 11 Handling Flush pipelines (cistern 2H) Requirements: The revision shaft is shortened in such a way that it is flush with the surface. Mechanism has been removed. Close corner valve. Loosen flexible hose on the filling valve (SW 19). Open the corner valve for a few seconds to rinse the pipe. Re-close corner valve.
  • Page 12 Handling Connect the flexible hose onto the filling valve (SW 19). Open corner valve. Flush pipelines (cistern 2L) Requirements: The revision shaft is shortened in such a way that it is flush with the upper edge of the tiles. Mechanism has been removed. Close corner valve.
  • Page 13 Handling Loosen flexible hose on the filling valve (SW 19). Open the corner valve for a few seconds to rinse the pipe. Re-close corner valve. Connect the flexible hose onto the filling valve. Open corner valve. Flush plate Visign for Style 10 13 from 20...
  • Page 14: Mount Flush Actuation

    Handling 3.2.2 Mount flush actuation Mount mechanism (cistern 2H) Hang the mechanism in the bow of the drain valve. Insert mechanism. The mechanism must sit exactly in the recesses in the cistern. Turn the mechanism's lock by 90° in a clockwise direction. ð...
  • Page 15 Handling Vertical installation (flush plate on the front of the cistern) Hang the mechanism in the bow of the drain valve. Insert mechanism. The mechanism must sit exactly in the recesses in the cistern. Turn the mechanism's lock by 90° in a clockwise direction. ð...
  • Page 16 Handling Hang the mechanism in the bow of the drain valve. Insert mechanism. In doing so, ensure that the tracks on the top and bottom edge of the mechanism are in the indentations in the revision shaft of the cistern. Turn the mechanism's lock by 90°...
  • Page 17: Mounting The Flush Plate

    Handling 3.2.3 Mounting the flush plate Requirements: The flush actuation has been mounted. Re-mount cistern casing. Insert the threaded bolts so deeply that the upper edge of the threaded bolt sticks out approx. 20 mm behind the upper edge of the tiles.
  • Page 18 Handling Screw the actuating rods into the threaded holes of the mechanism. Set the upper actuating rod flush with the basic panel. If necessary, shorten the actuating rod on the thread with a cutting knife. Set the lower actuating rod flush with the basic panel. If necessary, shorten the actuating rod on the thread with a cutting knife.
  • Page 19: Commissioning

    Handling Place and press the flush plate onto the basic panel. Commissioning 3.3.1 Setting the flush Set the flush volume on the drain valve of the cistern. Small flush volume (above): approx. 3–4 litres Large flush volume (below): approx. 6–9 litres Error, faults and remedy Error Cause...
  • Page 20: Disposal

    Handling Strong stains can be removed using typical household cleaner. Rinse the detergent thoroughly with clear water after the prescribed exposure time. There should be no residue on the components. Disposal Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.

Table of Contents