Advertisement
Table of Contents
Advertisement
Table of Contents
Summary of Contents for scope R4C
- Page 1 FRONT WHEEL SCOPE CYCLING MAINTENANCE MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS General Introduction Maintenance Intervals Required Tools FRONT WHEEL Hub Parts R3C / R4C / R5C Hub Parts R3D / R4D / R5D REMOVING THE BEARINGS REPLACING THE BEARINGS REAR WHEEL HUB PARTS R3C / R4C / R5C... -
Page 3: General Introduction
MAINTENANCE MANUAL GENERAL INTRODUCTION Congratulations on the purchase of Scope hubs and to enjoy riding. your new Scope Cycling wheelset. We advise you to keep this instruction This maintenance manual applies for manual. For any further information, all Scope wheels from 2017 onwards... -
Page 4: Maintenance Intervals
MAINTENANCE MAINTENANCE INTERVALS To guarantee a hassle-free performance of your Scope wheels and hubs, we recommend you to maintain them on a regular basis. For the hubs we recommend the following maintenance intervals. MAINTENANCE RIDING INTERVAL ACTION CONDITIONS Replace bearing grease... -
Page 5: Required Tools
All Scope wheels come with high-quality bearings from either SKF or CeramicSpeed, depending on your chosen model. For a proper installation and deinstallation of the bearings we advise you to use the Scope Bearing Press set, which included the following parts: PART NO. - Page 6 FRONT WHEEL R3C / R4C / R5C & R3D / R4D / R5D The maintenance procedure for the R3d, R4d, and R5d front wheel hubs is the same as for the R3c, R4c, and R5c front wheel hubs.
-
Page 7: Front Wheel
FRONT WHEEL HUB PARTS R3C / R4C / R5C PART NO. PART NAME 1 & 6 End Cap 2 & 5 Bearing Hub Shell Axle... -
Page 8: Hub Parts R3D / R4D / R5D
FRONT WHEEL HUB PARTS R3D / R4D / R5D PART NO. PART NAME 1 & 6 End Cap 2 & 5 Bearing Hub Shell Axle... -
Page 9: Removing The Bearings
FRONT WHEEL REMOVING THE BEARINGS To remove the bearings you’ll need the following tools: • Bearing Installation Tool (T1/T2/T3) • 2x Plastic Presshead (T6) Remove the end caps by inserting the bearing installation tool spindle (T1&T2) into one side of the hub and gently tap out the end-caps on both sides (1 & 8). Place the two small threaded plastic pressheads (T6) on a bearing as shown in the image and insert the bearing removal tool (T1&T2). -
Page 10: Replacing The Bearings
FRONT WHEEL REPLACING THE BEARINGS To replace the bearings you’ll need the following tools: • Bearing Installation Tool (T1/T2/T3) • Long Bearing Presshead (T4) • Short Bearing Presshead (T5) • 15mm Guide (T9) Apply a small amount of grease on both bearing seats of the hub. Carefully place one bearing (2) in the bearing seat without applying pressure. Place the long 1524/1528 (T5) presshead and 15mm guide (T9) on the bearing removal tool (T1&T2) with the 1524 side facing the hub. - Page 11 FRONT WHEEL Gently tighten the bearing removal tool and assure its correct position on the bearing. Tighten the bearing removal tool until the bearing is fully seated. Check the alignment to make sure the bearing runs smoothly. Insert the axle into the hub (5). Repeat steps 3-7 but do not use the 15mm guide (T9).
- Page 12 REAR WHEEL R3C / R4C / R5C & R3D / R4D / R5D The maintenance procedure for the R3C, R4C, and R5C rear wheel hubs is the same as for the R3D, R4D, and R5D rear wheel hubs.
-
Page 13: Rear Wheel
REAR WHEEL HUB PARTS R3C / R4C / R5C PART NO. PART NAME End Cap (DS) Freehub Bearing (DS) Freehub Spacer (DS) Lock Ring Freehub Body Freehub Bearing (NDS) Freehub Spacer (NDS) Pawls and Springs Hub Bearing (DS) Hub Shell... - Page 14 REAR WHEEL HUB PARTS R3D / R4D / R5D PART NO. PART NAME End Cap (DS) Freehub Bearing (DS) Freehub Spacer (DS) Lock Ring Freehub Body Freehub Bearing (NDS) Freehub Spacer (NDS) Pawls and Springs Hub Bearing (DS) Hub Shell Axle Hub Bearing (NDS) End Cap (NDS)
-
Page 15: Removing The Bearings
REAR WHEEL REMOVING THE BEARINGS To remove the bearings you’ll need the following tools: • Bearing Removal Tool (T1/T2/T3) • 1x Plastic Presshead (T6) • Large Spacer (T9) • Small Spacer (T8) Remove the freehub and hub cap from the hub by pulling it off the axle. Remove the freehub spacer from the axle. Pull off the non-drive side hub cap by hand. Place a small threaded plastic presshead (T6) on the bearing removal tool (T1&T2) and insert the tool into the axle from the drive side of the... - Page 16 REAR WHEEL Place a small threaded plastic presshead (T6) on the bearing removal tool (T1&T2) and insert it into the axle on the non-drive side of the hub. Place the large spacer (T7) on the opposite side of the hub and screw on the bearing removal tool handle (T3). Gently tighten the tool until the bearing is released.
-
Page 17: Replacing The Bearings
REAR WHEEL REPLACING THE BEARINGS To replace the bearings you’ll need the following tools: • Bearing removal tool (T1/T2/T3) • Long press head 1524/1528 (T4) • Short press head (1524/1528 (T5) • 15mm guide (T9) Apply a small amount of grease onto both bearing seats of the hub. Carefully place one bearing (2) on the bearing seat on the drive-side without applying pressure. Place the long 1524/1528 (T5) presshead and the 15mm guide (T9) on the bearing removal tool (T1&T2) with the 1524 side facing the hub. - Page 18 REAR WHEEL Gently tighten the bearing removal tool and assure its correct position on the bearing. Tighten the bearing removal tool until the bearing is fully seated. Check the alignment to make sure the bearings run smoothly. Insert the axle into the hub (11). Carefully place the other bearing (13) in the bearing seat on the non-drive side without applying pressure.
- Page 19 FOLLOW INSTAGRAM @scopecycling FACEBOOK / scopecycling YOUTUBE / scopecycling...
- Page 20 WWW.SCOPECYCLING.COM...