Sharp AR-FX12 Operation Manual page 68

STORING, EDITING, AND DELETING AUTO DIAL KEYS AND PROGRAMS
Use the numeric keys to enter the fax
10
number.
DIRECT ADDRESS / INDIVIDUAL
No.048
FAX No.
ENTER OWN FAX NO. VIA THE 10 KEY-PAD,THEN PRESS [OK].
0666211221
To insert a pause between digits of the number, touch
the [PAUSE] key. The pause appears as a hyphen "-
". Refer to page 8-6 to set the duration of the pause.
If you make a mistake, press the [C] key to clear one
digit at a time, and then enter the correct digit(s).
If you are not going to enter a sub-address and
password after the fax number, proceed to step 13.
NOTES
For information on sub-addresses and passcodes,
see "MEMORY BOXES AND SUB-ADDRESSES/
PASSCODES REQUIRED
TRANSMISSION" on page 4-2.
A maximum of 64 digits can be entered, including
the fax number, sub-address, passcode, any
pauses (hyphens), and slashes "/" (to separate the
sub-address and passcode).
If you need to enter a sub-address, touch
11
the [SUB ADDRESS] key and then enter
the sub-address with the numeric keys.
CANCEL OK
PRESS [OK].
PAUSE
SUB ADDRESS
12 If you wish to enter a passcode, touch the
[SUB ADDRESS] key once again and enter
the passcode with the numeric keys.
ADDRESS / PASS CODE VIA THE 10-KEY PAD
0666211221/3456/
Touch the [OK] key.
13
You will return to the one-touch key programming
screen and "REGISTRATION IS COMPLETED."
will appear in the touch panel.
The number (Speed Dial number) that appears next to
[No.] is used for Speed Dialing. This number is useful
when you frequently send faxes to the same destination.
NOTE
The "FAX No." line only shows 32 digits, regardless
of how many digits actually programmed.
6-4
NEXT EXIT
CANCEL OK
PAUSE
SUB ADDRESS
FOR F-CODE
When you touch the [SUB
ADDRESS] key, a slash is
entered after the fax number.
Continue by entering the sub-
address (max. 20 digits).
If you do not wish to enter a
passcode, proceed to step 13.
When you touch the
[SUB ADDRESS] key, a
slash is entered after the
sub-address. Continue
by entering the passcode
(max. 20 digits).
Touch the key, and then check the key
14
name.
The characters appearing next to the [NAME] key will
be displayed in the key. Only the first 9 characters of
the name entered in step 1 will be displayed.
If you need to change the name that will be
displayed in the key, touch the [KEY NAME] key.
DIRECT ADDRESS / INDIVIDUAL
No.048 REGISTRATION IS COMPLETED.
E-MAIL FAX
KEY NAME
SHARP CORPORATION
MODE 33.6kbps/NONE
15 Check the transmission settings.
The initial transmission settings are "TRANSMISSION
SPEED: 33.6 kbps"
CORRESPONDENCE MODE: NONE". To change
either of the settings, touch the [MODE] key.
DIRECT ADDRESS / INDIVIDUAL
No.048
REGISTRATION IS COMPLETED
E-MAIL FAX
KEY NAME SHARP CORPORATIO
MODE 33.6 kbps/NONE
Transmission speed
Speed selections are 33.6 kbps, 14.4 kbps, 9.6
kbps, and 4.8 kbps. The higher the number, the
faster the transmission speed.
NOTE
Set the transmission speed only when you know what speed
is most suitable, such as when you are sending a fax to a
foreign country and telephone line conditions are bad. If you
do not know the line condition, do not change this setting.
International correspondence mode
Selections are NONE, MODE 1, MODE 2, and MODE 3.
NOTES
When sending a fax to a foreign country, telephone line
conditions can sometimes distort the fax or interrupt the
transmission. Selecting
correspondence mode can help alleviate these problems.
If errors frequently occur when sending a fax to a foreign
country, try each of modes 1 to 3 and select the mode
that enables the best transmission.
16 When you have finished programming the
one-touch key, touch the [EXIT] key.
If you wish to program another one-touch
key, touch the [NEXT] key.
EXIT
NEXT
INTERNET-FAX
1/2
OX
USER 3
If you do not wish to
change the name, this
step is not necessary.
Refer to chapter 7 of the
"Operation manual (for
general information and
copier operation) for the
procedure for entering
characters.
and "INTERNATIONAL
If you do not wish to
change the settings, this
step is not necessary.
After touching the [MODE]
key, you can change either
of the two settings. When
finished, touch the [OK] key.
the right international
Pressing the [EXIT] key
returns you to the screen
of step 4 on page 6-2.
Touching the [NEXT]
key returns you to the
screen of step 1 on
page 6-3.