Page 1
Owner’s Manual Titan Series Combination Blanket/Fluid Warmer EC1850BL Enthermics Medical Systems An ISO 13485:2003 certified company W164 N9221 Water St | Menomonee Falls WI 53051 Tel 262-251-8356 | 800-TO-B-WARM generalinfo@enthermics .com www .enthermics .com Printed in the U.S.A. Specifications are subject to change without notice.
. fi led and actively pursued . Enthermics cannot, however, 2 . Do not sign a delivery receipt or a freight bill until fi le any damage claims, assume the responsibility of any a proper count has been made and inspection of all claims, or accept deductions in payment for such claims .
**Domestic ground shipping information. Contact the manufacturer for export weight and dimensions. experienced workers when moving or Appliances on casters can move or roll on uneven floors. leveling appliance and handling accessories. MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
NOTICE: For equipment delivered for use in any location regulated by the following directive: 2012/95/EC WEEE Do not dispose of electrical or electronic equipment with other municipal waste. MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
Weight** Net: 457 lbs (207 kg) Ship: 568 lbs (258 kg) Wire diagram is located under top lid of appliance. EC1850BL Shipping dimensions: 38" L x 38" W x 90" H Grounding reliability can only be achieved when appliance is...
Page 8
. IEC 61000-4-8 NOTE: UT is the a.c. mains voltage prior to application of the test level. MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
Page 9
NOTE: 1. At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. 2. These guidelines may not apply in all situations. Electromagnetic propagation is aff ected by absorption and reflection from structures, objects and people. MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
NOTICE: A temporary odor may be noticeable upon initial start-up of the warmer. Contact manufacturer if the odor persists a er a day or more of continuous use. MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
2 . Make sure the product inside the warmer is at the displayed for fi ve (5) seconds . Then the blanket correct temperature before using . chamber temperature set-point is displayed . MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
. NOTE: Failure to rotate the blankets can cause blankets to discolor aft er an extended period of time. MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
3 . Make sure the product inside the warmer is at the correct temperature before using . NOTE: If the alarm continues or reoccurs, the warmer needs to be serviced. MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
Page 14
(5) seconds. Then the controller displays the set operating temperature. 2 . Make sure the product inside the warmer is at the correct temperature before using . MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
7 . Load the fl uid chamber with appropriate fl uid containers . 8 . Make sure the warmer door is securely closed aft er initial loading and following each fl uid removal . MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
. Always wipe standing water as 7 . Clean the appliance glass with glass cleaner or quickly as possible . distilled vinegar . 8 . Replace the support assembly . MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
The set-point will be within +0/-1.12°C (+0/-2ºF) for injection fluids and within +0/-1.67°C (+0/-3ºF) for irrigation fluids. *Contact service for immediate repair. MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
. Contact service . MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL E-60 Real Time Clock Real time clock rechargeable battery backup has discharged . Checksum Error • Plug the warmer into the outlet for 30 minutes .
Page 21
MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL *E-83 EEPROM Error Call service for help resetting the control . E-87 EEPROM Error Stored off sets corrupted . Off sets reset to 0 .
(blanket shelf, top right) Zone 3 (blanket, bottom left) Zone 4 (blanket, bottom right) Front of warmer Part numbers and drawings are subject to change without notice. MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
Page 25
Service EC1850BL - Electrical chassis Item Description Par t POWER SUPPLY, 20W, 5 VOLT DC BA-34965 2 SURGE PROTECTION CIRCUIT BOARD BA-38876 1 RELAY BOARD, 4-ZONE, 120V BA-39302 2 RELAY BOARD, 4-ZONE, 230V BA-39304 2 CONTROL BOARD CC-36126 2 CABLE, RELAY BOARD CB-35193 2 CABLE, 12"...
Page 26
Service EC1850BL - Power inlet assembly Item Description Part SCREW, M3 x 0.5 x 10MM PAN SC-22620 CORD FOR 4" BOX FAN CD-33338 1 FAN, AXIAL, 120MM, 100-240V FA-39406 IEC POWER LINE FILTER FI-38581 FUSE HOLDER FU-35033 NUT, M4, KEPS, ZINC PLATED NU-36319 4 PLUG, 1/2"...
Page 28
Service EC1850BL - Fan assembly BLANKET AND FLUID CAVITY BLANKET AND FLUID CAVITY Item Description Part FAN, AXIAL, 120MM, 100-240V FA-39406 1 FAN GUARD GD-2396 SCREW, M4 x 0.7 x 50MM PAN SC-29261 4 NUT, M4, KEPS, ZINC PLATED NU-36319 4 MN-39362 •...
Page 29
Service EC1850BL - Cavity sensors Item Description Part SCREW, M4 x 0.7 x 10MM PAN SC-22273 2 SENSOR MOUNTING BLOCK BK-29882 2 FLUID CAVITY, CAVITY SENSOR, 48" WIRE PR-38590 1 BLANKET CAVITY, CAVITY SENSOR, 24" WIRE PR-37140 1 MN-39362 •...
Wire Diagram Serial number is required for all inquiries. Part numbers and drawings are subject to change without notice. MN-39362 • • Titan Series Combination Blanket/Fluid Warmer Rev 0 • 04/18 EC1850BL...
Page 31
Enthermics Medical Systems An ISO 13485:2003 certified company W164 N9221 Water St | Menomonee Falls WI 53051 Tel 262-251-8356 | 800-TO-B-WARM generalinfo@enthermics .com www .enthermics .com Printed in the U.S.A. Specifications are subject to change without notice. Made in the U.S.A.