Advertisement
E
NGLISH
I
P
R
N S TA L L I N G T H E
O P L O C
E M O T E L E V E R
1.
Remove the grip, shifter and brake lever from the left side of the bar
when viewed from the rider's perspective. Install PopLoc remote
inboard of shifter and brake lever. Tighten lever clamp bolt to 20
in-lb. (Fig. 1)
2.
Reinstall the brake, shifter and grip according to the manufacturer's
instructions.
A
T TA C H I N G T H E C A B L E
1.
Install shifter cable in PopLoc lever and cut a length of cable
housing to fit between the remote and cable stop of the remote
collar. Be sure to debur the housing ends.
N
:
B
OTE
RAKE CABLE HOUSING MUST BE USED FOR CORRECT
.
PERFORMANCE
2.
If using a PopLoc remote with adjustable compression damping
set the damper control in the middle position (approximately 2.5
turns from fully closed). For both PopLoc and PopLoc Adjust
levers depress the lockout lever toward the handlebar until the
lever engages into the lock position.
3.
Feed cable through housing and around remote lockout cap. Pull
the cable back towards the housing stop collar. Make sure that
the cable pinch bolt is contacting the housing stop collar. Tighten
cable anchor bolt to 8 in-lb. Verify fork is locked at this setting.
(Fig.2)
4.
Press release button on PopLoc remote to check action of
remote. The cable anchor bolt on the remote top cap should
return to approximately 3 or 4 o'clock. (Fig. 3).
P P
D D
L L
S S
U U R R E E
E E
I I T T E E
Y Y S S T T E E M M
Pure DeLite offers a wide range of rebound damping
adjustment. In addition, adjusting the air pressure in this
chamber (right fork leg) helps fine-tune the small bump ride
(threshold or break-away) of the fork. This chamber should
be inflated to a minimum of 10 psi and a maximum of 60
psi. Less air pressure will make the fork feel softer and helps
absorb smaller bumps, while more air pressure will make the
fork feel stiffer.
We recommend adjusting the positive and negative air pressures before you adjust the air
pressure in the Pure Delite chamber (right side, rider's perspective).
N
: A
P
D
L
OTE
IR PRESSURE IN THE
URE
E
ITE SYSTEM SHOULD NOT BE USED TO TUNE THE SPRING RATE OR
.
BOTTOM OUT FORCE REQUIRED FOR THE FORK
8
SRAM C
. • SID U
M
ORPORATION
SER
:
:
Fig. 1
Fig. 2
( ( R R
) )
A A C C E E
Fig. 3
954-311120-000, R
SRAM C
ANUAL
ORPORATION
To maintain the high performance, safety, and long life of your fork, periodic maintenance is
required. If you ride in extreme conditions, maintenance should be performed more frequently.
*
W
E RECOMMEND THIS SERVICE BE PERFORMED BY A QUALIFIED BICYCLE MECHANIC
SERVICE INFORMATION OR INSTRUCTIONS
YOUR LOCAL
. B
SRAM C
EV
ORPORATION
• SID U
M
SER
ANUAL
M M
A A I I N N T T E E N N A A N N C C E E
,
VISIT OUR WEBSITE AT WWW
R
S
.
OCK
HOX DEALER OR DISTRIBUTOR
Torque Tightening Values
Top Caps
65 in-lb
Brake Posts
80 in-lb
Cartridge Sleeve Retainer 60 in-lb
Air Shaft Nut
45 in-lb
Damper Shaft Bolt
60 in-lb
Remote Lockout clamp bolt 8 in-lb
Pure top cap clamp screw 12 in-lb
Climb-It knob screw
12 in-lb
• A
2005
PRIL
E
NGLISH
. T
O OBTAIN
.
.
ROCKSHOX
COM OR CONTACT
9
Advertisement
