Lang CSE12-208VCD Installation And Operation Instructions Manual
Electric clamshell grill
Hide thumbs
Also See for CSE12-208VCD:
Related Manuals for Lang CSE12-208VCD
Summary of Contents for Lang CSE12-208VCD
- Page 1 ® ELECTRIC CLAMSHELL CSE12-208VCD, CSE12A-1, CSE12A-2 Glass Surface CSE12A-1G thru CSE12A-6G Contact Clam CCSE12A-208 Installation and Operation Instructions 2M-W363 Rev. F 3/19/2015 CSE12A...
- Page 2 CONTROL PANEL. NO USER-SERVICABLE PARTS INSIDE. REPAIRS SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY. NOTICE Using any part other than genuine Lang factory supplied parts relieves the manufacturer of all liability. Lang reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.
-
Page 3: Table Of Contents
Exploded View & Parts List CSE12-208VCD, CSE12A-1, CSE12A-2 ... . 12-13 CSE12A-1G thru 6G (glass surface) ....14-15 CSE12-CC208 (contact clam) . -
Page 4: Saftey Precautions
Safety Precautions Lang manufacturing, hereby disclaims any and all responsibility for injury, damage, loss or other claim that may occur to person or property from improper alteration, modification, addition, operation, maintenance or service, whether it be mechanical, electrical, or otherwise, which may occur from such improper alteration, modification, addition, operation, maintenance or service to this piece of equipment. -
Page 5: Technical
Make a written request for inspection upon unpacking and finding concealed damage within 15 days of delivery. Keep all packing material for inspection. Do not return damaged merchandise to Lang Manufacturing. File your claim with the carrier. -
Page 6: Installation Electrical Connection
INSTALLATION Electrical Connection Verify griddle installation was performed as directed in the installation instructions. Connect electrical service to the box at the back of the griddle. Electrical specifications are located on the data plate. Clearance Use this griddle only in non-combustible locations. Maintain clearances of base appliance. -
Page 7: Initial Start-Up
INITIAL START UP Each unit is preheated, tested and calibrated at the factory prior to shipment. However, due to temperature and climate changes during shipment the unit can absorb moisture. Check griddle for moisture and allow the unit to dry before placing the unit into full operation. -
Page 8: Cleaning Daily
CLEANING Daily Cleaning Clean the exterior of the appliance with cleaner and water. Wipe drip shield between hood and griddle to remove any grease. Weekly Cleaning Allow the hood to burn off any carbon build up after high use periods. With a cold griddle, lower the hood and allow the hood to cook for 30 minutes. -
Page 9: Hood Stop Adjustments
HOOD STOP ADJUSTMENT Units with an Adjustable Hood Stop Installed have the capablity to adjust between a 40° to 45° degree settings. These simple steps will assist you in accomplishing this. If you have diffi culty accomplishing this, please call a qualifi ed service agent or Star Manufacturing Technical Service Department. 1. -
Page 10: Operating Instructions Contact Clam Only
OPERATING INSTRUCTIONS CONTACT CLAM ONLY 1. Turn unit on by placing switch in "ON" position. The "Heat On" indicator, program number and display will flash indicating unit is heating. When the preset temperature is reached, the heating light, display and program light indicator will stop flashing followed by 3 beeps. -
Page 12: Exploded View & Parts List
Parts List Parts List ETL File 68964 Rev.A2007... - Page 13 PARTS LIST March 19, 2015, Rev. F Model: CSE12-208VCD, CSE12A-1-208V, CSE12A-2-208V Clamshell Hood Fig No. Part Description Application CSE12-208VCD, A-1-208, A-2-208, A-3-208, A-4-208, 2N-11160-32-2 STLHTR208VXLH1600W42.5WSI A-5-208, A-6-208 2N-11160-32-4 STLHTR240VXLH1600W42.5WSI CSE12A-1-240, A-2-240, A-3-240, A-4-240, A-5-240, A-6-240 2E-30500-02 TRM STRP 4 POLE 30A 600V...
-
Page 14: Cse12A-1G Thru 6G (Glass Surface)
Purchase these items together Model: CSE12A-1G thru CSE12A-6G CLAMSHELL HOOD GLASS SK2522, Rev. -, 6/15/2011... - Page 15 HANDLE ASSY. CSE12 K9-XLH-707 FOREWARD HOODWRAP ASSY 2M-60301-W2 LANG CLAMSHELL LOGO IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available.
-
Page 16: Cse12-Cc208 (Contact Clam)
See Detail SK2742, Rev. - , 02/10/14 Model: CCSE12A1 Contact Clam... - Page 17 Part Number Description K9-XLH-709-1 HANDLE ASSY. CSE12 K9-XLH-821 TOP COVER K9-XLH-822 COVER CLOSE OFF PLATE 2M-60301-W2 LANG CLAMSHELL LOGO K9-XLH-761-1 LEFT HINGE ARM PIVOT ASSY K9-XLH-762-1 RIGHT HINGE ARM PIVOT ASY K9-XLH-721-4 PIVOT ASSY CCSE12 K9-XLH-644 PISTON ROD TUBE SLEEVE...
- Page 18 SK2743, Rev. - , 02/10/14 Detail K9-XLH-580 Control Box Assembly Model: CCSE12A1 Control Box Fig No. Part Number Description 2C-20103-02 SCRW SM PLT 10 X .5 PHLSL K9-XLH-580-1 CONTROL BOX TOP-CCSE12A 2E-70505-17 CONDUIT CNNCTR 1/2 90o 1M-70502-03 60 inches CONDUIT TUBNG 1/2FLEX, (sold by the inch) K9-XLH-580-4 CONTROL BOX BACK ASSY 2E-Z3335...
- Page 19 6 TAN 5 TAN...