Specifications; Accessories; Setup And Assembly - Eaton ET1187 Operator's Manual

Specifications and Accessories
ET1187-001
(Bench Mount)
ET1187-002
(Truck Mount)
Bench Mount
Truck Mount

Setup and Assembly

1. Your new ET1187 crimp
machine comes as-
sembled for ease of
shipment. Before use,
the machine must be
assembled to the base
with the supplied quick
release pins.
2. Remove the cap from
the top of the hydraulic
cylinder port. Apply a
small amount of Ac-
crolube lubricant to the
o-ring on the supplied
–06, 90 degree o-ring
boss fitting. Hand tighten
the fitting, then rotate the
fitting counter clockwise
not more than one full

SPECIFICATIONS

Crimper Dimensions: 22" tall x 16" width x 14" deep
Weight: 70 lbs.
(machine & stand only)
Pump Requirements: Reservoir Capacity:
Pressure Rating: 10,000 psi (690 bar)
Hose Production Capacity: (-6 through -16 4S)
CRIMP MACHINE PART NUMBERS
ET1187-001 = Bench mount machine with bracket only, no pump, no tooling
(for premium hose GH681/H180, GH781/H280, GH493/H430)
ET1187-002 = Truck mount machine with bracket only, no pump, no tooling
(for premium hose GH681/H180, GH781/H280, GH493/H430)
ET1187-003 = Bench mount machine with bracket only, no pump, no tooling
(for standard hose EC115, EC215, EC415)
ET1187-004 = Truck mount machine with bracket only, no pump, no tooling
(for standard hose EC115, EC215, EC415)
ET1187C-0017 = Bench Mount Bracket
ET1187C-0019 = Truck Mount Bracket
PUMP PART NUMBERS*
ET1000PK-001 = 2 - Stage Hand Pump
ET1000PK-002 = Air/Hydraulic Pump
ET1000PK-003 = 110 Volt Electric Pump
ET1000PK-004 = 12 Volt DC Electric Pump
* These pump kits include the pump,
connecting hose assembly, and all of
the adapters necessary to connect the
pump to the ET1187 crimp machine.
rotation, until the fitting
is pointing to the side or
rear of the machine away
from the operator.
3. Tighten the lock nut on
the o-ring boss fitting
using 24-26 ft. lbs. of
assembly torque.
4. Install the pump connect-
ing hose assembly to
the cylinder adapter with
the 3/8" JIC fitting using
18-20 ft. lbs. assembly
torque.
5. Do not exceed an 8"
minimum bend radius
of the pump connecting
36 cu. in (590 cc)
ACCESSORY PART NUMBERS
T-400-G = 1.5 oz. Tube
High Efficiency PTFE Grease
FF91455 = 16 oz. Can
High Efficiency PTFE Grease
ET1187C-0008PR = Barrel for
premium hose machine
ET1187C-0008WR = Barrel for
standard hose machine
ET1187C-0009PR = Knob for
premium hose machine
ET1187C-0009WR = Knob for
standard hose machine
hose when attaching the
hose to the pump and
cylinder.
6. If using your own pump,
make sure it has the
requirements listed in
the specifications section
above.
7. Place the pump on the
work surface to either
side of the crimp ma-
chine. Install the 90 de-
gree adapter to the pump
pressure port (Male
NPTF threads should be
tightened following the
hex-marking procedure
of 2 to 3 turns past hand
tight).
EATON ET1187 Operating Instructions E-EQCR-11001-E1 November 2018
8. Prior to use, remove ex-
cess air from the hydrau-
lic system. This can be
accomplished by cycling
the machine approxi-
mately five times.
9. Secure the machine
frame to a stable work
surface using lag screws
or other suitable
fasteners.
10. The Crimp Specification
Chart may be installed
on any one of the three
front shroud panels.
User preference on which
panel.
3