Closed-Loop Crimp Terminals - Omron Q2A-A Series Installation & Operation Instructions

Screw Adapter
Bit
M4
Bit
*1
M5
Bit
M6
Bit
M6
Bit
M8
Bit
M10
*1 When wiring drive models 2056 and 4089 and smaller, select the correct tools for the wire gauge.
*2 Use 6.35 mm (0.25 in) bit socket holder.
*3 Use a torque wrench that can apply this torque measurement range.
■

Closed-Loop Crimp Terminals

To comply with UL standards on drive models from 2257 and from 4208, use UL-approved closed-loop crimp
terminals. Use the tools recommend by the terminal manufacturer to crimp the closed-loop crimp terminal.
Closed-loop crimp terminals from JST Mfg. Co., Ltd. and insulation caps from Tokyo DIP Co., Ltd. are
recommended.
Comply with local standards for correct wire gauges in the region where the drive is used.
Contact the manufacturer or your nearest sales representative to order.
Note:
To comply with UL standards, use only insulated crimp terminals or crimp terminals with insulation tubing. Use UL-Listed, vinyl-
coated insulated copper wires for operation with a continuous maximum permitted temperature of 75 °C at 600 V.
Table 2.2 Closed-Loop Crimp Terminals and Insulation Caps (200 V Class)
Recommended Gauge (AWG, kcmil)
R/L1 U/T1
Model
S/L2 V/T2
T/L3 W/T3
2004 - 2021 -
2030, 2042 -
2056 -
2070 - 2110 -
2138 -
2169, 2211 -
-
-
2257
2/0 × 2P 2/0 × 2P
-
TOMPYEUOQ2A03B AC Drive Q2A Installation and Operation Instructions
Table 2.1 Recommended Wiring Tools
Bit
Model Manufacturer
SF-BIT-SL 1,0X4,0-70 PHOENIX CONTACT
SF-BIT-SL 1,2X6,5-70 PHOENIX CONTACT
SF-BIT-HEX 5-50 PHOENIX CONTACT
SF-BIT-SL 1,2X6,5-70 PHOENIX CONTACT
SF-BIT-HEX 6-50 PHOENIX CONTACT
SF-BIT-HEX 8-50 PHOENIX CONTACT
-, +1 +3
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - 1/0 × 2P
- -
- 4/0 × 2P -
Torque Driver Model
(Tightening Torque)
TSD-M 3NM
(1.2 - 3 N∙m)
Wire Gauge
≤ 25 mm 2
(AWG 10):
TSD-M 3NM
(1.2 - 3 N∙m)
Wire Gauge
2
≥ 30 mm
(AWG 8):
-
-
-
-
-
Crimp
Terminal
Terminal
Screw Size
Model
10 M4 R5.5-4
8 M5 R8-5
6 M6 R14-6
6 M6 R14-6
4 M6 R22-6
4 M8 R22-8
3 R38-10
- R60-10
M10
- 80-10
- R100-10
2 Attachments
Torque Wrench
-
Wire Gauge
≤ 25 mm 2
(AWG 10):
-
Wire Gauge
2
≥ 30 mm
(AWG 8):
*2 *3
4.1 - 4.5 N∙m
*2 *3
5 - 9 N∙m
*2 *3
3 - 3.5 N∙m
*2 *3
8 - 12 N∙m
*2 *3
12 - 14 N∙m
Crimping Tool
Insulation
Cap Model
Tool Model Die Jaw
YA-4 AD-900 TP-005
YA-4 AD-901 TP-008
YA-4 AD-902 TP-014
YA-4 AD-902 TP-014
YA-5 AD-953 TP-022
YA-5 AD-953 TP-022
TD-224, TD-
TP-038
212
TD-225, TD-
TP-060
213
YF-1
YET-150-1
TD-227, TD-
TP-080
214
TD-228, TD-
TP-100
214
EN 25
EN