Hotsy 1800 Series Operator's Manual
Hide thumbs
Also See for 1800 Series:
- Operator's manual (30 pages) ,
- Service manual (27 pages) ,
- Service manual (32 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Advertisement
Table of Contents
Related Manuals for Hotsy 1800 Series
Summary of Contents for Hotsy 1800 Series
- Page 1 STATIONARY ELECTRIC OPERATOR’S MANUAL 8916831-1 For technical assistance or the dealer nearest you consult our web page at www.hotsy.com 8.916-831.0...
-
Page 3: Table Of Contents
Warranty IMPORTANT If the pressure washer demonstrates other symptoms or the corrective actions listed do not correct the problem, contact the local authorized Hotsy Service Center. The Hotsy Service Center can be identified by visiting www.hotsy.com. When ordering from your dealer, please provide the following:... -
Page 4: Important Safety Information
(GFCI). If rated more than 250 volts, or more than tion must be worn when using THIS EQUIPMENT. single phase this product should only be connected this equipment. to a power supply receptacle protected by a GFCI. 8.916-831.0 • HOTSY STATIONARY ELECTRIC • REV. 10/13... - Page 5 Do not use liquid fuel. Have a qualified stream at people, or severe in- RISK OF INJECTION serviceman install and service your equipment. OR SEVERE INJURY jury or death will result. TO PERSONS. KEEP CLEAR OF NOZZLE. 8.916-831.0 • HOTSY STATIONARY ELECTRIC • REV. 10/13...
- Page 6 WARNING: If connection is made to portable water supply, a back flow device must be provided. Follow the maintenance instructions specified in the manual. Example Of Down Draft Diverter For Gas Fired Machines 8916831-4 8.916-831.0 • HOTSY STATIONARY ELECTRIC • REV. 10/13...
-
Page 7: Component Identification
Exhaust Vent High Pressure Nozzle Thermal Rupture Disk Wand High Pressure Hose Fresh Water Inlet Pump Switch Burner Switch Chemical Valve Garden Hose Thermostat Trigger (not included) Detergent Bucket (not included) 8916831-2 8.916-831.0 • HOTSY STATIONARY ELECTRIC • REV. 10/13... -
Page 8: Assembly
Install the pressure hose on the pressure washer as shown in Figure 1. Garden Hose (Not Included) 8916831-7 Figure 3 - Float Tank/Garden Hose Adapter Pressure Hose 8916831-5 Figure 1 - Pressure Hose Installation 8.916-831.0 • HOTSY STATIONARY ELECTRIC • REV. 10/13... -
Page 9: Installation
(available from most heating contractors). A draft regulator will permit proper upward flow of exhaust flue gases. Hotsy natural and LP gas series pressure washers that incorporate a natural draft burner assembly designed to Power In... -
Page 10: Installation Instructions
(power vent) must be installed by a licensed contractor Locking Screw who can calculate size, operation connections and as- Air Shutter sociated dampeners. Hotsy is not a licensed contractor and as such we are unable to make recommendations for suitable make and model of power vents. Air Band It is important that the licensed contractor consult local building codes. -
Page 11: Installation
149.1 and CSA-149.2 “Installation Code for Gas Burning refer to Figure 8. The trigger lock should be used Appliances”. whenever the trigger gun is not in use. 8.916-831.0 • HOTSY STATIONARY ELECTRIC • REV. 10/13... - Page 12 If burner was used, turn OFF burner switch and al- low pump to run cold water through coil for several minutes. Press pump STOP switch. Turn water supply OFF. Squeeze trigger of trigger gun to relieve system pressure. 8.916-831.0 • HOTSY STATIONARY ELECTRIC • REV. 10/13...
-
Page 13: Cleaning Techniques & Storage
• Liquids containing solvents (i.e., paint thinner, gasoline, oils) • Tri-sodium phosphate products • Ammonia products • Acid-based products These chemicals will harm the machine and will dam- age the surface being cleaned. 8.916-831.0 • HOTSY STATIONARY ELECTRIC • REV. 10/13... -
Page 14: Maintenance
1000 hours of operation with Chevron SRI #2 lubricant or equivalent. If the motor is not equipped with grease fittings, the pump motor bearings are permanently lubricated and will not require any additional lubrication. 8.916-831.0 • HOTSY STATIONARY ELECTRIC • REV. 10/13... -
Page 15: Troubleshooting
Gas valve switch in OFF Place switch in ON position. NOT PRODUCE position HOT WATER Inadequate fuel supply Check fuel supply. Pump switch turned off Pump must be running before burner will light. 8.916-831.0 • HOTSY STATIONARY ELECTRIC • REV. 10/13... - Page 17 Hotsy does not authorize any other party, including authorized Hotsy Distributors, to make any representation or promise on behalf of Hotsy, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility to ensure that the installation and use of Hotsy products conforms to local codes.
- Page 18 If you need service on your pressure washer, contact your local Hotsy dealer or visit www.Hotsy.com. Smart phone users scan the code below to link directly to the Service Request page. Form #8.916-831.0 • Revised 10/13 • Printed in U.S.A. by Hotsy...