Specification - Optimum SW-1019 Operating Instructions Manual

24. D uring operation the hair straightener becomes hot. Do not
place it near flammable materials.
25. A llow the hair straightener to cool before putting it away.
Allow to cool before storing.
26. D o not use the appliance with a voltage converter.
27. D o not direct hot air toward eyes, hands or other heat-
sensitive areas.
28. D o not unplug by pulling on cord. To unplug grasp the
plug.
29. R isks exist even if the hair straightener is switched off.
Always unplug the appliance from the electrical outlet
immediately after using and before cleaning.
30. D o not wrap the cord around the appliance (risk of breaking
the cord).
31. D o not cover the hair straightener as it might cause heat
accumulating inside of it.
32. I n case of handing over the appliance to another person
please inform that person about these instructions for use.
33. A ttachments may be hot during and after use. Allow them
to cool before handling.
34. Do not use attachments that are not recommended.
35. A lways unplug the hair straightener from the electrical
outlet after use.
36. I f the hair straightener is used in the bathroom, always
unplug it from the electrical outlet after use, as it may pose
a risk even when the appliance is switched off.
37. F or additional safety it is recommended to install an RCD
device in the electric circuit supplying the sockets with
a maximum rated residual current of 30mA. For more
information please consult a qualified electrician.
Description
1. LED Display
2. Temperature selection buttons ( + )
3. Temperature selection buttons ( – )
4. «on/off» button
5. Styling plates
6. Spin lock cover
7. Swivel cord
Microprocessor supported styling
Thanks to its highly sophisticated microprocessor and its LED
control display, the straightener allows you to personalise your
settings.
•. I ndividual temperature choice: Using the temperature
selection buttons (2) (3), you can adjust the temperature
in 20°C steps in a range between 120°C and 220°C. We
recommend the following temperature settings.
Hair structure
Fine, porous, coloured, bleached
Normal
Strong, resistant
. . . and for professional styling results
SW1019_IM_203.indd 7
The higher the temperature setting, the faster you will get .
a sleek straightening result. When working with the maximum
temperature setting, you should not treat the same strand more
than once.
•. .Express h eat up time: After only 30 seconds, the appliance
is ready for use.
•. .Safety auto off: For safety reasons, the appliance
automatically switches off after 30 minutes. If you want to
keep on straightening, simply press the «on/off» button (4)
again shortly.
Getting started
• C onnect the appliance to an electrical outlet and push the .
«on/off» button (4) for 2 second to turn it on.
• D uring heat-up, the display turns red. The appliance is
delivered with a default temperature setting of 180°C.
• A fter approx. 30 seconds, the display turns green indicating
that the minimum styling temperature is reached. You can
start using the appliance.
Styling
Preparation
• M ake sure your hair is completely dry before using the
appliance.
• F irst, comb your hair through with a wide toothed comb to
remove tangles.
• S ection your hair off. Starting close to the roots, take a thin
section of hair (strands of 3–4 cm maximum) and clamp it
firmly between the styling plates.
How to straighten your hair
• G ently run the straightener through the entire length of the
hair, slowly and steadily, from roots to the ends without
stopping for longer than 2 seconds. This will ensure best
straightening results without damaging your hair. The
styling plates (5) ensure easy and smooth gliding.
• Y ou can create flicks at the hair ends by slowly turning the
appliance either outwards or inwards before releasing a
strand.
After use
After each use, switch off the appliance by pushing the «on/
off» button (4) for 2 seconds.
Cleaning
Always unplug before cleaning. Never immerse the appliance
in water. Clean the appliance with a damp cloth and use a soft
cloth to dry.
Subject to change without notice.
Temperature
setting
This product conforms to the European Directives EMC
120 C-160 C
0 0
89/336/EEC and Low Voltage 2006/95/EC.
160 C-190 C
0 0

SPECIFICATION:

Power supply: 220-240V 50Hz
190 C-220 C
0 0
Power consumption: 40W

2010-12-28...15:36:40