Advertisement
Quick Links
IMPORTANT— Read all assembly instructions
Permanent Bases w/adjustable feet
Tilt Table Includes
• Tilt Table with (4) temporary shipping bases (steel)
• Empty crate for returning steel Shipping Bases
• Permanent Bases with adjustable bolt feet (2)
• Free Arm (for power and water)
• Flip Down Leg
• (4) Mid-table Countertop Pegs (oak)
• Slab Keepers (steel & wood construction) (2)
• (2) Yellow 150 lb & (2) Red 70 lb Counter-Tension
Cords (on the Table)
• Extra Yellow 150 lb & Red 70 lb Counter-Tension
Cords
• Slab Safety Strap
1
© 2010 Harris AccuGlide Saws, All Rights Reserved, Patents/Patents Pending
prior to assembling Tilt Table
Free Arm—
Overhead Electrical
& Water
Safety Strap
Center Line
Countertop Pegs
Slab Keepers
Counter Tension Cords
Flip Down Leg
Hardware & Tools
• (2) 3/8-16 Bolts (extra)
• 4 Ton Bottle Jack for assembling table
Suggested Assembly Tools
• Drill or impact drill gun (use with Phillips bit
• Phillips head drive bit (removing crate materials)
• 9/16" socket (removing crate and assembling
• 9/16" standard wrench or ratchet wrench
(return after use)
and 9/16" socket)
table base)
Advertisement
Related Manuals for Accuglide Ez-tilt
Summary of Contents for Accuglide Ez-tilt
- Page 1 • 9/16” socket (removing crate and assembling Cords (on the Table) table base) • Extra Yellow 150 lb & Red 70 lb Counter-Tension • 9/16” standard wrench or ratchet wrench Cords • Slab Safety Strap © 2010 Harris AccuGlide Saws, All Rights Reserved, Patents/Patents Pending...
- Page 2 3) Pump the jack handle, lifting the table no more than 1/8” off the ground. 4) Completely remove all six bolts connecting the base to the shipping leg with a 9/16” wrench. © 2010 Harris AccuGlide Saws, All Rights Reserved, Patents/Patents Pending...
- Page 3 9) Tighten all six bolts with a 9/16” wrench. Ensure sufficient force is used but do not over tighten. YOU’RE HALFWAY THERE! You’re now ready to install the second base by repeating steps 1-9. Once the second leg base is permanently installed continue to step 10. © 2010 Harris AccuGlide Saws, All Rights Reserved, Patents/Patents Pending...
- Page 4 Leaving the table in the horizontal position for more than a day will weaken the Counter-Tension Cords and limit their counter balancing ability. © 2010 Harris AccuGlide Saws, All Rights Reserved, Patents/Patents Pending...
- Page 5 CAUTION: Regularly Inspect Counter-Tension Cords. If any defect from original condition is found, immediately discontinue use of the table until replacement cords are acquired from AccuGlide. 2) After tilting the table to the horizontal position pull the lock pin and flip the Center Leg to the down position.
-
Page 6: Important Safety Note
If any malfunction in the Vertical Latch (pictured right) is detected, discontinue use of the table and contact AccuGlide Saws immediately. Never load or operate the table without the latch fully operational. After tilting the table to the upright position and the lock pin has snapped in place, always confirm the table is solidly locked in position by giving the handle a quick pull. - Page 7 On more abrasive stones, cutting into the table alone will be sufficient for blade dressing. Hard non-abrasive granites will require supplemental dressing with a dressing stone or cinder block. Refer to the AccuGlide directions for guidelines on proper diamond blade dressing.