Related Manuals for Telematrix 9602IPMWD
Summary of Contents for Telematrix 9602IPMWD
- Page 1 VoIP Phone User Manual For model: 9602IPMWD 9602IPMWD5 9600IPMWD 9600IPMWD5 Version: V2.0...
-
Page 2: Table Of Contents
1 INTRODUCTION ....................5 1.1 Hardware overview ....................5 1.2 Software overview ....................5 2 PHONE MENU SETTINGS .................7 2.1 Key features ......................7 3 THE OPERATION METHOD OF TELEPHONE ..........3.1 How to make a phone call? ..................3.1.1 Basic call ......................9 3.1.2 Hold key........................9 3.1.3 Volume control .................... - Page 3 4.5 Provisioning ......................26 4.6 System Settings ...................... 28 4.6.1 Syslog Server ...................... 28 4.6.2 Time Settings ...................... 29 4.6.3 User Management ....................30 4.6.4 System Actions....................31 4.6.5 DECT ........................31 5 SHORTCUT KEYS .............
- Page 4 The phone started, get Provisioning Server address by DHCP Server, then the phone LED lights flashing, and issued a "beep beep" prompt tone, "Config ID". Through the digital keyboard input after the ID, and then enter the "#", then the opportunity to Provisioning Server automatically load the configuration file, automatically restart after the success;...
-
Page 5: Introduction
◆ VAD/CNG: can save bandwidth ◆ TFTP: Trivial File Transfer Protocol 1. INTRODUCTION This is the 9602IP network telephone user manual. Before the use of 9602IP phone, you need to make some phone configuration for normal use. This book illustrates how to use keyboard and Web phone service configuration page. - Page 6 Call Function NAT Traversal Call Hold STUN Call Waiting Configuration Call forward Web Browser Caller ID Keypad DTMF Firmware Upgrade IN Band TFTP RFC2833 HTTP SIP Info ...
-
Page 7: Phone Menu Settings
2 PHONE MENU SETTINGS Using the web configuration page: familiar with the PC user can use the method to configure the phone. Sequentially press the "**47#" button, then the phone will voice broadcast address IP. Directly in the browser address bar entering the address of the IP phone can log in web page, enter the login name: admin, password: admin 2.1 KEY FEATURES... - Page 8 Conversation Increase the receiver volume Volume+ Stand-by Increase the ringer volume Conversation Decrease the receiver volume Volume- Stand-by Decrease the ringer volume Stand-by Line1 state (only for two-line model) Line1 Stand-by Line2 state (only for two-line model) Line2 Conversation Mute Mute The last number redial and call Redial...
-
Page 9: The Operation Method Of Telephone
3 THE OPERATION METHOD OF TELEPHONE HOW TO MAKE A PHONE CALL You could make a phone call after the phone configuration items are set up. Please check if the cable is properly connected before use. 3.1.1 Basic call 1. Making the call by handset After the handset is placed off-hook, dial and use “#”... -
Page 10: Mute
3.1.4 Mute During the call, if you do not want to let them hear your own voice, you can press "Mute" key, so that the other party cannot hear your voice, and you can hear the sound of other end. 3.1.5 Memory Key In addition to serving as a storage function, but also can be used as hold, DND, transfer and conference function. -
Page 11: Toggle Between Base Unit And Handset
“Message” LED on base unit will stop blinking and the “Message” LED on handset will also stop blinking and emit the prompt sound of successful registration. Note: each base unit can register up to 5 handsets. 3.1.11 Toggle between Base Unit and Handset When the base unit is in conversation, press “Line1”/“Line2”... -
Page 12: Network Setting
4.2 N ETWORK ETTING You can get the network information of phone in the page. 4.2.1 WAN Setting WAN port setting page. WAN port supports the static IP, dynamic allocation IP and PPPoE. -
Page 13: Basic Setting
4.2.1.1 Basic Setting Basic Setting Select the network mode of WAN port; the default is DHCP Network Mode Configure the WAN port network connection mode Link mode Set the main DNS address Primary DNS Set the secondary DNS address Secondary DNS 4.2.1.2 DHCP If your local network has a DHCP server, 3302IP phone can get WAN network information from the DHCP server. -
Page 14: 3Static Ip Setting
4.2.1.3Static IP Setting Static IP setting (WAN port network mode is set to Static IP) Set static IP address Static IP Address Set subnet mask with static IP Subnet Mask Set the default gateway with static IP Default Gateway 4.2.1.4 PPPoE Setting PPPoE Setting (Required if Network Mode is set to PPPoE) Set the PPPoE user account User Account... -
Page 15: 2Lan Settings
Note: if the user wants to access the phone through the WAN port, then he / she must use the new IP address to access the phone after changing IP address of WAN port. 4.2.2 LAN Settings LAN port setting interface 4.2.2.1 LAN Settings LAN Settings Link Mode... -
Page 16: Nat
4.2.2.2 NAT IP Address IP address of LAN port Subnet Mask Subnet Mask DHCP Server DHCP server is enabled or not IP Pool Start IP address assignment start address IP Pool End IP address assignment end address MAX Leases Maximum release time DNS Relay DNS relay is enabled or not 4.3 V... - Page 17 Register Server Use Service Enable or disable SIP registration Display Name Set the displayed name of phone's SIP account User Name Set the username (SIP account) Authorization User Name Confirm the SIP account Password Set the password of SIP account Register Server Port Set the port No.
-
Page 18: Audio Setting
Protocol Control Disable: the phone prohibits MWI function. Even if it receives a NOTIFY from server that there is a new voice mail, the phone will not have a prompt. Enable(Subscribe): the phone enables MWI function and will send SUBSCRIBE. If it receives a NOTIFY from server that there is a new MWI Subscribe voice mail, the MWI LED on phone will blink to give a prompt. - Page 19 Audio Setting Sound and Volume Control Configure the handset output volume. The control range is 1~7. Handset The default is 5. Configure the speakerphone output volume. The control range is Speaker 1~7. The default is 5. Ring Tone Configure the ringer volume. The range is 1~7. The default is 4. The signal standard.
-
Page 20: Call Feature
l iLBC l G.722 Packet Data Size The packet data size is 20mS by default. IBLC 15.2k iLBC 15.2kbit/s is enabled or not. The default is disable. G.723.1 5.3k G.723.1 5.3kbit/s is enabled or not. The default is disable. Voice VAD/CNG Voice VAD Enable or disable Mute detection function Enable or disable the comfortable noise. - Page 21 Call Feature Programmable Keys&MWI Touchlite 1. Set the number in speed dial key. Mem1~Mem10 2. Set the second function. Each memory can be arbitrarily set as Hold, DND, Transfer, Conference, Multicast Paging MWI Touchlite Set the number in shortcut key for voice message pickup. Park Mode Enable or disable Park function.
-
Page 22: Dial Rule
The set range is 1-9s, for example 3s, the hotline number will be sent out immediately after 3s with the phone off-hook and without pressing any key. As long as any key is pressed within the set time, the time counting will stop. Enable or disable auto answer function. - Page 23 Dialing Rules Configuration Entry Name Description 1. Set the end of dialing rules, there are 2 kinds to choose from: Dialing Rules End with “#”. Configuration Timeout: Timeout setting. Set the waiting time for dialing end, the unit is second, the default is 5s. The default is "#"...
-
Page 24: Multicast Paging
4.3.5 Multicast Paging You can use the multicast function that will simply, conveniently and efficiently send the timely notice to each member of the multicast group. The multicast key is set on the telephone to send the multicast RTP stream to the pre-configured multicast address. Through the configuration monitoring multicast address on the phone, listen and play the RTP stream sent by the multicast address, the RTP stream multicast process does not involve SIP signaling. -
Page 25: Advanced Settings
The multicast voice coding format: 0:G.711a; 1:G.711u; Multicast Paging Codec 2:G.723; 3:G.729; 4:iLBC; 5:G.722 Multicast Listening You can set to listen up to 10 different multicast addresses on the phone which can be used to receive the multicast RTP stream sent by them. If the priority of incoming multicast RTP stream is lower than the priority of current call, the phone will automatically ignore the multicast RTP listening Address... -
Page 26: Provisioning
QoS Setting Entry Name Description Enable or disable Voice VLAN function. The default is Voice VLAN disable. The Voice Video Tag. The range is 2~4094. The default Voice VID(TAG) is 136. User Priority User priority. The default is 0. Enable or disable Data VLAN function. The default is Data VLAN disable. - Page 27 No file was selected Select the file No file was selected Select the file Provisioning Provision Options DHCP Options Support DHCP Options parameter or not. Auto Redirection Support Auto Redirection or not MAC File Support that the Config. filename is MAC address or not Config ID Support that the Config.
-
Page 28: System Settings
0-24, 0 - Disable, 1-24 hour selects any hours among 1-24 and generates a random number as the minute of upgrade among 0~60 ConfigID Update Time and delays a few seconds to begin to detect if Config ID file is updated. -
Page 29: Time Settings
Server Port Set the port # of syslog server. The default is 49494. default The default of logintelval is 0. Events only Log information print interval is 1min. Events plus periodic Logint is the setting range of lower interval. status inteval Log interval time setting. -
Page 30: User Management
Enable Daylight Daylight savings enable or disable. Time Shift(minutes) Time difference (minute) Daylight Savings Start Dates Month Daylight Savings Start Month Week of Month Week of Month Day of Week Hour Hour of Day Daylight Savings Stop Dates Month Daylight Savings Stop Month Week of Month Week of Month Day of Week... -
Page 31: System Actions
Set the password for webpage login in the identity of Administrator Password administrator. The default is admin. Input administrator password again Verify Password verification. Remote Administration Set the username of remote administrator. The default CetisAdmin User is admin. Set the login password of remote administrator. The CetisAdmin Password default is admin. -
Page 32: Shortcut Keys
Select the power level of registered handset. The power level is related to the receiving range. The level 0 is minimum, level 7 has Power Level the maximum receiving range. Frequency Select the DECT frequency band: select the different countries. 5 SHORTCUT KEYS 1. - Page 33 FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the 9602IPMWD and is the answer not in the manual?
Questions and answers