Contents - Craftsman 113 Owner's Manual

addifionaR safety instruchons for mo nter..planer
!3, TO be sure you will make a depth of cut as panned, WHEN USED WITH A 3450 RPM MOTOR NEVER
always lower the infeed tab e S ightty beYOnd the SUBSTITUTE OTHER PULLEYS TO NCREASE THIS
depth Wanted, then raise the table to the desired d_,pth. SPEED BECAUSE IT COULD BE DANGEROUS.
• PROM FREQUENT USE OF YOUR JOINTER-PLANER)
TO BECOME COMMONPLACE. ALWAYS REMEMBER
15; Never leave the Jointer-P aner work area w th the power
On, before the Jointer-Planer has come to a complete
stop, or without removing and storing the switch key.
16. Never operate the Jointer-Planer with protective cover
on the unused shaft end of the motor removed.
17, Do not attempt to perform an abnormal or little-used
operation without study and the use of adequate hold
down/push blocks, jigs, fixtures, stops, etc.
lB. DO NOT perform tayou_, assembly, or setup work on
the tab|e while the cutting tool is rotating.
WARNING: THE 2" JOINTER-PLANER PULLEY AND
THE 2-1/2" MOTOR PULLEY FURNISHED WILL RUN
THE CUTTER HEAD AT APPROXIMATELY 4300 RPM
THAT A CARELESS FRACTION OF A SECOND IS
SUFFICIENT TO INFLICT SEVERE INJURY,
t9. Read and follow the instructions appearing on the
danger label on the cutter guard.
DANGER
- FOR YOUR OWN SAFETY
READ AND UNDERSTAND OWNER*S
MANUAL BEFORE OPERATING MACHINE
1 WEAR SAFETY GOGGLES PER ANSI Z87 1 AT ALL TIMES
2 NEVER PERFORM A JOINT1NG OR PLANING OPERATION W_TH CUTTER
HEAD OR DRIVE GLIARD REMOVED
3 NEVER MAKE A JOtNTING OFt PLANING CUT DEEPER THAN _/g INCH
4 ALWAYS USE HOLD DOWN/PUSH SLOCKS EOR JOINTtNG MATERIAL
NARROWER THAN 3 INCHES OR PLANING MATER_AL THINNER THAN 3
INCRES.
WEAR YOUR
The operation of any power tool can result in foreign
objects being thrown into the eyes, which can result n
severe eye damage. Always wear safety goggles complying
with ANSI Z87.1 (shown on Package) before commencing
power too! operation. Safety Goggles are available at Sears
retail or catalog stores.
cortfents
POWER TOOL GUARANTEE ............... 2
GENERAL SAFETY INSTRUCTIONS FOR
POWER TOOLS ............................ 2
ADDITIONAL SAFETY INSTRUCTIONS FOR
JOINTER-PLANER .......................... 3
MOTOR SPECIFICATIONS AND ELECTRICAL
REQUIREMENTS ........................... 5
Connecting to Power Source Outlet ........ 5
Check Motor Rotation .................... 5
UNPACKING AND CHECKING CONTENTS .... 6
ASSEMBLY ................................ 7
Assembling Steel Legs ................... 7
GETTING TO KNOW YOUR JOINTER-PLANER 12
Depth of Cut HandwheeJ .................. 12
Fence Locks and Stops ................... 12
Fence Tilt Scale .......................... 13
Cutter Guard .......................... 14
Infeed Table .......................... 14
On-Off Switch ........................... 16
BASIC JOtNTER-PLANER O PERATION ....... 18
Feeding the Workpiece ................... 18
Using the Hold Down/Push Blocks ........ 19
Beveling ................................. 20
MAINTENANCE ............................ 21
Mounting Jointer-Planer On Recommended
Craftsman Stand ......................... 8
Checking Cutterblade Screws .............. 8
Installing Sliding Guard ................. 9
Mounting Switch .......................... 9
Mounting Recommended Craftsman Motor
and Belt Guards ....... ; ..................
Replacing Cutter Blades .................. 21
Installing Cutter Guard Spr=ng ............. 23
Sharpening Cutter Blades ................. 24
GENERAL MAINTENANCE .................. 25
LUBRICATION .............................. 25
TROUBLE SHOOTING ...................... 26
RECOMMENDED ACCESSORIES ............ 26
-Check Mot0r Rotation .:_ :..: ......... ;.... 10 : REPAIR PARTS ............................. 27
Jointer-PUlley Beff G uardlnstaliation :: :.. i I