Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ParaZero SafeAir M200
Summary of Contents for ParaZero SafeAir M200
- Page 1 SafeAir M200 INSTALLATION GUIDE...
-
Page 2: Table Of Contents
Copyright © 2018 ParaZero Drone Safety Systems. All rights reserved. All intellectual property rights in this publication are owned by ParaZero Drone Safety Systems and protected by applicable copyright laws and international treaty provisions. ParaZero Drone Safety Systems retains all rights not expressly granted. - Page 3 Tel – +972-36885252 30 Dov Hoz Kiryat Ono, Israel 5555626 www.parazero.com About This Guide This guide describes the installation of the ParaZero SafeAir M200 drone safety system that is compatible for your DJI M200/210/210RTK drone. SafeAir™ M200 Installation Guide www.parazero.com...
-
Page 4: Chapter 1 - Safety Instructions
A step by step video can be found here: https://youtu.be/fA9Y4CcYFeA The ParaZero SafeAir M200 is a safety system designed to deploy almost instantaneously, by using a special pyrotechnic mechanism, which must be handled with caution. Figure 1 – SafeAir M200 System The system incorporates two safety elements –... -
Page 5: Figure 2 - Safeair M200 Safety Cover And Safety Pin
The system is provided with the cover stretched over the parachute canister. Do not remove the safety cover until you complete the installation, and you are ready to fly. Safety Pin Safety Cover Figure 2 – SafeAir M200 Safety Cover and Safety Pin SafeAir™ M200 Installation Guide www.parazero.com... -
Page 6: Chapter 2 - Package Contents
Package Contents The SafeAir M200 package includes the parts shown in Figure 3. Figure 3 – SafeAir M200 Package Contents Table 1 – SafeAir M200 Package Contents Description The main parachute system, which contains the SMARTAIR smart computer and its electronics plus all other electronics, is preinstalled on the mounting plate and ready for use. -
Page 7: Chapter 3 - Installation
Disconnect the drone’s landing gear joints from the airframe by releasing the three connection screws. Replace the three original M200 screws with the ParaZero longer screws (six total). On the screws, make sure to place the washer first and then the spring washer above it before inserting the screws into the landing gear joints. -
Page 8: Connecting The Terminateair To The Drone
Place the TerminateAir system into its position. The ParaZero icon should be facing you, with the word ParaZero at the front. The location of this component is above the battery compartment. Insert the two long screws in order to connect the TerminateAir to both arms, and close them firmly at the bottom using the provided toolset. -
Page 9: Connecting The Electrical Wires
That the safety cover remains in its place, covering the system. Be sure that the SafeAir M200 battery is not connected. If it is, disconnect the battery. Take the main parachute system (see #1 in Table 1) and turn it over until its bottom side is facing you. -
Page 10: Connecting The Parachute System To The Legs
For Matrice 210 and 210 RTK models - It is recommended to install the extended GPS module provided. The SafeAir M200 system is now installed, and you are ready for operation! 3.5 Activating the System Charge the M200 battery for two hours using the supplied charger, as shown below. - Page 11 Place the battery back inside and close the door. For IP43 water protection, verify that the door is sealed. Then, rotate the handle in a clockwise direction. Pull the safety cover back down and close it. Verify that the lever of the TerminateAir is in its down position. Lever SafeAir™ M200 Installation Guide www.parazero.com...
- Page 12 Turn on the drone’s power. Disable the Upward IR sensor: On your DJI GO app, press the 3 dots icon on the upper right corner of the screen: Select the drone icon: Scroll down Deselect Upward Obstacle Avoidance SafeAir™ M200 Installation Guide www.parazero.com...
-
Page 13: Takeoff And Landing
Pull the safety pin out all the way. The system powers up. During power-up, the SafeAir M200 LED displays solid YELLOW. After a few seconds, a single short beep is heard and that the SafeAir M200 LED on the parachute system changes to BLUE. -
Page 14: Chapter 4 - Operating Guidelines
After the Disarm signal has been heard, insert the safety pin all the way in before touching the drone. • Place the safety cover back on the system. The system is now safe and secured. SafeAir™ M200 Installation Guide www.parazero.com... -
Page 15: Replacing The Batteries
Once the batteries are released, slide the small knob towards the right and then lever the lever. The batteries can be removed now. Be sure to lower the lever after replacing the batteries, to prevent the batteries from falling during an emergency activation of the system. Releasing knob Lever SafeAir™ M200 Installation Guide www.parazero.com... -
Page 16: Troubleshooting
LED Flashes Orange This indicates that the system’s cellular connectivity is inactive. This does not affect operational performance. Fly Safely! Should you have questions, contact our support team at – contact@parazero.com Phone – +972-36885252 SafeAir™ M200 Installation Guide www.parazero.com... - Page 17 Operate Drones Everywhere, Safely Tel – +972-36885252 30 Dov Hoz Kiryat Ono, Israel 5555626 www.parazero.com...
Need help?
Do you have a question about the SafeAir M200 and is the answer not in the manual?
Questions and answers