Subscribe to Our Youtube Channel
Related Manuals for IBASE Technology FWA8708-C
Summary of Contents for IBASE Technology FWA8708-C
- Page 1 FWA8708-C FWA8708-H 1U Rackmount Network Appliance User’s Manual Version 1.0 (Dec. 2018)
- Page 2 No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”).
-
Page 3: Compliance
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm). • Lead (Pb) • Mercury (Hg) • Cadmium (Cd) • Hexavalent chromium (Cr6+) • Polybrominated biphenyls (PBB) • Polybrominated diphenyl ether (PBDE) FWA8708-C / FWA8708-H User Manual... -
Page 4: Important Safety Information
Do not disassemble, repair or make any modification to the device. Disassembly, modification, or any attempt at repair could generate hazards and cause damage to the device, even bodily injury or property damage, and will void any warranty. FWA8708-C / FWA8708-H User Manual... -
Page 5: Caution
Software in use (such as OS and application software, including the version numbers) 3. If repair service is required, you can download the RMA form at http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and contact your distributor or sales representative. FWA8708-C / FWA8708-H User Manual... -
Page 6: Table Of Contents
AT & ATX Mode (JP2) ............20 2.5.2 PEG Configuration (JBAT1, JBAT2) ........21 2.5.3 Clearing CMOS Data (JBAT3) ..........22 2.5.4 Clearing ME Register (JBAT4) ..........23 Connectors Quick Reference ..............24 2.6.1 External Power Switch Connector (J2) ......... 25 FWA8708-C / FWA8708-H User Manual... - Page 7 Security Settings ................... 48 Boot Settings..................49 Save & Exit Settings................50 Appendix ...................... 51 I/O Port Address Map ................52 Interrupt Request Lines (IRQ) ............... 54 Digital I/O Sample Code ................ 57 Watchdog Timer Configuration .............. 62 FWA8708-C / FWA8708-H User Manual...
-
Page 8: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Optional Accessories • Specifications • Overview • Dimensions... -
Page 9: Introduction
• SOHO • • Enterprise Each product is designed to address the distinctive requirements of its respective market segment from cost effective entry-level solutions to high throughput and performance-bound systems for the enterprise level. FWA8708-C / FWA8708-H User Manual... -
Page 10: Features
250W Full Range ATX Power Supply • Power Cord (180 cm) • Rack Mount Bracket Models with 1+1 redundant PSU: • FWA8708 • 300W 1+1 Redundant Power Supply Unit • Power Cord (180 cm) • Rack Mount Bracket FWA8708-C / FWA8708-H User Manual... -
Page 11: Optional Accessories
MHz; max. 32 GB UDIMM (ECC or non-ECC) (ECC or non-ECC) • ® 6 x Intel I210AT GbE ® 6 x Intel I211AT GbE controller controller Network • ® 2 x Intel I210IS GbE controller FWA8708-C / FWA8708-H User Manual... - Page 12 • Single PSU: 1 x 100 ~ 240V AC Inlet, full range 250W ATX power supply AC Inlet • 1+1 RPSU: 2 x 100 ~ 240V AC Inlet, with 2 hot-swappable 300W power supply modules FWA8708-C / FWA8708-H User Manual...
- Page 13 Operating: 0.25 Grms / 3 ~ 500 Hz (Z-axis) Vibration • Protection Non-operating: 1.0 Grms / 3 ~ 500Hz (Z-axis) Shock Sawtooth wave 40G (X/Y/Z-axis) Protection All specifications are subject to change without prior notice. FWA8708-C / FWA8708-H User Manual...
-
Page 14: Overview
Name LCM Display with 4 buttons USB 3.0 Ports Console Port GbE LAN Ports LED Indicators Reserved Area for IBN module (for FWA8708-C only) (From top to bottom: Status, HDD, Power) User Self-Defined GPIO Button FWA8708-C / FWA8708-H User Manual... - Page 15 PCIe (x8) Expansion Card Slot 4 Power Switch VGA Port Single Power Supply Unit (via an onboard pin-header or via the optional IPMI module) System Fan Modules Reduntant Power Supply Oblique View • • FWA8708-C FWA8708-H FWA8708-C / FWA8708-H User Manual...
-
Page 16: Dimensions
General Information 1.7 Dimensions Unit: mm FWA8708-C / FWA8708-H User Manual... -
Page 17: Chapter 2 Hardware Configuration
Chapter 2 Hardware Configuration The information provided in this chapter includes: • Installation / Replacement • Information and locations of connectors... -
Page 18: Installation / Replacement
8 screws as shown below to pull out the lid. Configuration inside: Areas B allows for optional IBN modules, two 2.5” or one 3.5” HDD/SSD. Area A allows for optional two 2.5” or one 3.5” HDD/SSD, or for expansion cards. FWA8708-C / FWA8708-H User Manual... -
Page 19: Network Module Installation / Removal
2.1.1 Network Module Installation / Removal Note: IBN module is purchasable and applicable for FWA8708-C only. Release two screws of a network module and pull it out carefully as shown below for replacement and installation. 2.1.2 HDD Installation / Removal After you remove the device cover, you can see the optional areas A and B as shown below allowing for optional HDD/SSD and expansion cards installation. - Page 20 3. Take out the HDD and install a new one onto the tray. Fasten 4 screws back for each HDD. 4. Secure the tray with HDD from the bottom of the device. Note the screw holes for different sizes of HDD/SSD as ilustrated below. FWA8708-C / FWA8708-H User Manual...
-
Page 21: Memory Installation / Replacement
3. Gently push the module in an upright position until the ejector tabs of the memory slot close to hold the module in place when the module touches the bottom of the slot. To remove the module, press the ejector tabs outwards with your fingertips to eject the module. FWA8708-C / FWA8708-H User Manual... -
Page 22: Ipmi Module Installation / Replacement
If you need to install an IPMI module, remove the system lid firstly and then follow the instructions below. Note: IPMI module is optionally purchasable and applicable for FWA8708-C only. 1. Locate the IPMI slot and align the key of the module with that on the slot. -
Page 23: Fan Module Installation / Removal
If you need to install or replace a redundant power supply unit, push the latch downwards, grasp the handle, pull the PSU out carefully and replace with a new one. 2.2 Pinout for Console Port ➔ Signal Name Signal Name Ground Ground FWA8708-C / FWA8708-H User Manual... -
Page 24: Setting The Jumper
When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e. turned On. When a jumper cap is removed from two jumper pins, this jumper is open, i.e. turned Off. FWA8708-C / FWA8708-H User Manual... -
Page 25: Jumper & Connector Locations On Motherboard
2.4 Jumper & Connector Locations on Motherboard Motherboard for FWA8708-C: MBN805C FWA8708-C / FWA8708-H User Manual... - Page 26 Hardware Configuration Motherboard for FWA8708-H: MBN805H FWA8708-C / FWA8708-H User Manual...
-
Page 27: Jumper Quick Reference
Factory Use Only JP1, JBMC1, JBMC2 Note: The following motherboard drawings in this section are illustrated by the example of MBN805C. 2.5.1 AT & ATX Mode (JP2) Function Pin closed Illustration AT Mode (Default) ATX Mode FWA8708-C / FWA8708-H User Manual... -
Page 28: Peg Configuration (Jbat1, Jbat2)
Hardware Configuration 2.5.2 PEG Configuration (JBAT1, JBAT2) JBAT1 JBAT2 The PEG bifurcation is only configurable for FWA8708-C. 1 x PCIe (x16) is always used for FWA8708-H. Function Pin closed Illustration JBAT1: Open 1 x PCIe (x16) JBAT2: Open JBAT1: Close... -
Page 29: Clearing Cmos Data (Jbat3)
2.5.3 Clearing CMOS Data (JBAT3) Function Pin closed Illustration Normal (Default) Clearing CMOS FWA8708-C / FWA8708-H User Manual... -
Page 30: Clearing Me Register (Jbat4)
Hardware Configuration 2.5.4 Clearing ME Register (JBAT4) Function Pin closed Illustration Normal (Default) Clearing ME Register FWA8708-C / FWA8708-H User Manual... -
Page 31: Connectors Quick Reference
FAN_CPU1, FAN1, FAN2, Fan Connector FAN3, FAN4 Console & Double Stack USB 3.0 Connector External VGA Connector USB 3.0 Port FWA8708-C: J4, J5, J6, J7 DDR4 UDIMM Slot FWA8708-H: J5, J7 IPMI Slot Mini-PCIe Slot M.2 M2280 Slot Fiber LAN Connector... -
Page 32: External Power Switch Connector (J2)
Hardware Configuration The following motherboard drawings in this section are illustrated by the example of MBN805C. 2.6.1 External Power Switch Connector (J2) Signal Name Signal Name ATX_PSON#_EN Ground FWA8708-C / FWA8708-H User Manual... -
Page 33: Usb 2.0 Connector (J15)
2.6.2 USB 2.0 Connector (J15) Signal Name Signal Name 5VDUAL 5VDAUL USB_PN8 USB_PN9 USB_PP8 USB_PP9 Ground Ground FWA8708-C / FWA8708-H User Manual... -
Page 34: Pm Bus Port (J20)
Hardware Configuration 2.6.3 PM Bus Port (J20) The PM Bus port J20 is only a vailable for FWA8708-C. Signal Name Signal Name SMB_PWR_5VDUAL_CLK Ground SMB_PWR_5VDUAL_DAT VCC3_3 PL_SMBAlert FWA8708-C / FWA8708-H User Manual... -
Page 35: System Function Connector (Jp3)
2.6.4 System Function Connector (JP3) Signal Name Signal Name VCC5 Speaker Ground Ground VCC5 5VDUAL BYPASSLED0- 5VDUAL BYPASSLED1- Ground ATXPWR_BTN# Ground FRST_OUT VCC3_3 -HDD_LED FWA8708-C / FWA8708-H User Manual... -
Page 36: Digital I/O Connector (Jp4)
Hardware Configuration 2.6.5 Digital I/O Connector (JP4) Signal Name Signal Name Ground VCC5 INT0_SIOGP22 INT0_SIOGP25 INT0_SIOGP23 INT0_SIOGP26 INT0_SIOGP24 INT0_SIOGP27 FWA8708-C / FWA8708-H User Manual... -
Page 37: External Sata Power Connector (Cn1, Cn4, Cn5)
2.6.6 External SATA Power Connector (CN1, CN4, CN5) CN1: CN4: CN5: Signal Name Signal Name VCC5 Ground Ground VCC12 FWA8708-C / FWA8708-H User Manual... -
Page 38: Lcm Connector (Cn7)
Hardware Configuration 2.6.7 LCM Connector (CN7) (with RS-232 signal) Signal Name Signal Name LCM_RD1 VCC5 LCM_TD1 Ground FWA8708-C / FWA8708-H User Manual... -
Page 39: Atx Power Connector (J1, J18)
ATX Power Connector (J1, J18) J18: Assignment Assignment Ground +12V Ground +12V Ground +12V Ground +12V J18: Assignment Assignment 3.3V 3.3V 3.3V -12V Ground Ground PS-ON Ground Ground Ground Ground Ground Power good 5VSB +12V +12V +3.3V Ground FWA8708-C / FWA8708-H User Manual... -
Page 40: Fan Connector (Fan_Cpu1, Fan1, Fan2, Fan3, Fan4)
Hardware Configuration 2.6.9 Fan Connector (FAN_CPU1, FAN1, FAN2, FAN3, FAN4) FAN1: FAN2: FAN3: FAN_CPU1: FAN4: CPU_FAN, FAN1, FAN2, FAN3: Assigment Assigment Ground FAN_TACH VCC12 FAN_PWM FAN4: Assigment Assigment Ground FAN_TACH VCC12 FWA8708-C / FWA8708-H User Manual... -
Page 41: Chapter 3 Bios Setup
Chapter 3 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Security Settings •... -
Page 42: Introduction
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. FWA8708-C / FWA8708-H User Manual... -
Page 43: Main Settings
3.3 Main Settings BIOS Setting Description System Date Sets the date. Use the <Tab> key to switch between the data elements. System Time Set the time. Use the <Tab> key to switch between the data elements. FWA8708-C / FWA8708-H User Manual... -
Page 44: Advanced Settings
Enables / Disables processor Turbo Mode (requires Intel Speed Step or Intel Speed Shift to be available and enabled). C states Enables / Disables CPU power management. Allows CPU to go to C states when it’s not 100% utilized. FWA8708-C / FWA8708-H User Manual... -
Page 45: Trusted Computing
10 & 8. TCG_2: Support new TCG2 protocol and event. Physical Presence Spec Selects a version of PPI spec version 1.2 or 1.3 to tell OS to support it. Note: Some HCT tests might not support 1.3. FWA8708-C / FWA8708-H User Manual... -
Page 46: Sata Configuration
Enables PCH to aggressively enter link power state. Serial ATA Port 0/1/2/3 Enables / Disables a Serial ATA port. 3.4.4 Smart Settings BIOS Setting Description Smart Self Test Run Smart Self Test on all HDDs during POST. FWA8708-C / FWA8708-H User Manual... -
Page 47: Nct5523D Super I/O Configuration
You can enable / disable the serial port and select an optimal settings for the Super IO device. Restore AC Power Loss Select AC power state when power is re- applied after a power failure. Options: Power Off, Power On, Last State FWA8708-C / FWA8708-H User Manual... - Page 48 IO = 3F8h; IRQ = 3, 4, 5, 6, 7 • IO = 2F8h; IRQ = 3, 4, 5, 6, 7 • IO = 3E8h; IRQ = 3, 4, 5, 6, 7 • IO = 2E8h; IRQ = 3, 4, 5, 6, 7 FWA8708-C / FWA8708-H User Manual...
- Page 49 IO = 3F8h; IRQ = 3, 4, 5, 6, 7 • IO = 2F8h; IRQ = 3, 4, 5, 6, 7 • IO = 3E8h; IRQ = 3, 4, 5, 6, 7 • IO = 2E8h; IRQ = 3, 4, 5, 6, 7 FWA8708-C / FWA8708-H User Manual...
-
Page 50: Nct7904D Hw Monitor
Temperatures / Voltages These fields are the parameters of the / Fan Speed hardware monitoring function feature of the motherboard. The values are read-only as monitored by the system and showing the PC health status FWA8708-C / FWA8708-H User Manual... -
Page 51: Lan Bypass Configuration
WDT monitor system hang & initiates a reboot. • Firewall Mode: All LAN ports in bypass until OS has control ability to change LAN ports in normal. • Custom Define: All LAN ports can be configured independently. FWA8708-C / FWA8708-H User Manual... -
Page 52: Serial Port Console Redirection
Console Redirection The settings specify how the host computer Settings and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings. Sets parameters of Console Redirection. FWA8708-C / FWA8708-H User Manual... - Page 53 Flow Control Flow control can prevent data loss from buffer overflow. When sending data, if the receiving buffers are full, a “stop” signal can be sent to stop the data flow. Options: None, Hardware RTS/CTS FWA8708-C / FWA8708-H User Manual...
-
Page 54: Usb Configuration
XHCI Hand-off This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver. USB Mass Storage Driver Enables / Disables USB mass storage driver Support support. FWA8708-C / FWA8708-H User Manual... -
Page 55: Security Settings
3.5 Security Settings BIOS Setting Description Administrator Password Sets an administrator password for the setup utility. User Password Sets a user password. FWA8708-C / FWA8708-H User Manual... -
Page 56: Boot Settings
Selects the keyboard NumLock state. Quiet Boot Enables / Disables Quiet Boot option. Network Controls the execution of UEFI and Legacy Network OpROM. Options: Do not launch, UEFI, Legacy Boot Option Priorities Sets the system boot order. FWA8708-C / FWA8708-H User Manual... -
Page 57: Save & Exit Settings
Exits system setup after saving the changes. Save Changes and Reset Resets the system after saving the changes. Discard Changes and Resets system setup without saving any Reset changes. Restore Defaults Restores / Loads defaults values for all the setup options. FWA8708-C / FWA8708-H User Manual... -
Page 58: Appendix
Appendix This section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration. • I/O Port Address Map • Interrupt Request Lines (IRQ) • Digital I/O Sample Code • Watchdog Timer Configuration... -
Page 59: I/O Port Address Map
Programmable interrupt controller 0x00000030-0x00000031 Programmable interrupt controller 0x00000034-0x00000035 Programmable interrupt controller 0x00000038-0x00000039 Programmable interrupt controller 0x0000003C-0x0000003D Programmable interrupt controller 0x000000A0-0x000000A1 Programmable interrupt controller 0x000000A4-0x000000A5 Programmable interrupt controller 0x000000A8-0x000000A9 Programmable interrupt controller 0x000000AC-0x000000AD Programmable interrupt controller FWA8708-C / FWA8708-H User Manual... - Page 60 Intel(R) UHD Graphics 630 0x00005000-0x00005FFF Intel(R) PCI Express Root Port #8 - A33F 0x00003000-0x00003FFF Intel(R) PCI Express Root Port #12 - A333 0x0000EFA0-0x0000EFBF Intel(R) SMBus - A323 0x00008000-0x00008FFF Intel(R) PCI Express Root Port #5 - A33C FWA8708-C / FWA8708-H User Manual...
-
Page 61: Interrupt Request Lines (Irq)
Intel(R) I211 Gigabit Network Connection #7 IRQ 4294967267 Intel(R) I211 Gigabit Network Connection #8 IRQ 4294967266 Intel(R) I211 Gigabit Network Connection #8 IRQ 4294967265 Intel(R) I211 Gigabit Network Connection #8 IRQ 4294967264 Intel(R) I211 Gigabit Network Connection #8 FWA8708-C / FWA8708-H User Manual... - Page 62 Intel(R) I211 Gigabit Network Connection #9 IRQ 4294967236 Intel(R) I211 Gigabit Network Connection #9 IRQ 4294967286 Intel(R) I211 Gigabit Network Connection #10 IRQ 4294967285 Intel(R) I211 Gigabit Network Connection #10 IRQ 4294967284 Intel(R) I211 Gigabit Network Connection #10 FWA8708-C / FWA8708-H User Manual...
- Page 63 Intel(R) PCI Express Root Port #8 - A33F IRQ 4294967288 Intel(R) PCI Express Root Port #12 - A333 IRQ 4294967293 Intel(R) PCI Express Root Port #5 - A33C IRQ 4294967294 Intel(R) PCIe Controller (x16) - 1901 FWA8708-C / FWA8708-H User Manual...
-
Page 64: Digital I/O Sample Code
NCT5523D_DATA_PORT (NCT5523D_BASE+1) //--------------------------------------------------------------------------- #define NCT5523D_REG_LD 0x07 //--------------------------------------------------------------------------- #define NCT5523D_UNLOCK 0x87 #define NCT5523D_LOCK 0xAA //--------------------------------------------------------------------------- unsigned int Init_NCT5523D(void); void Set_NCT5523D_LD( unsigned char); void Set_NCT5523D_Reg( unsigned char, unsigned char); unsigned char Get_NCT5523D_Reg( unsigned char); //--------------------------------------------------------------------------- #endif //__NCT5523D_H FWA8708-C / FWA8708-H User Manual... - Page 65 Dio5Initial(); //for GPIO20..27 Dio5SetDirection(0x0F); //GP20..23 = input, GP24..27=output printf("Current DIO direction = 0x%X\n", Dio5GetDirection()); printf("Current DIO status = 0x%X\n", Dio5GetInput()); printf("Set DIO output to high\n"); Dio5SetOutput(0x0F); printf("Set DIO output to low\n"); Dio5SetOutput(0x00); return 0; //--------------------------------------------------------------------------- FWA8708-C / FWA8708-H User Manual...
- Page 66 //NewData : 1 for input, 0 for output Set_NCT5523D_LD(0x07); //switch to logic device 7 Set_NCT5523D_Reg(0xE8, NewData); //--------------------------------------------------------------------------- unsigned char Dio5GetDirection(void) unsigned char result; Set_NCT5523D_LD(0x07); //switch to logic device 7 result = Get_NCT5523D_Reg(0xE8); return (result); //--------------------------------------------------------------------------- FWA8708-C / FWA8708-H User Manual...
- Page 67 = Get_NCT5523D_Reg(0x20); if (ucDid == 0xC4) //NCT5523D?? goto Init_Finish; } NCT5523D_BASE = 0x00; result = NCT5523D_BASE; Init_Finish: return (result); //--------------------------------------------------------------------------- void Unlock_NCT5523D (void) outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK); outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK); //--------------------------------------------------------------------------- void Lock_NCT5523D (void) outportb(NCT5523D_INDEX_PORT, NCT5523D_LOCK); //--------------------------------------------------------------------------- FWA8708-C / FWA8708-H User Manual...
- Page 68 Lock_NCT5523D(); //--------------------------------------------------------------------------- void Set_NCT5523D_Reg( unsigned char REG, unsigned char DATA) Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); outportb(NCT5523D_DATA_PORT, DATA); Lock_NCT5523D(); //--------------------------------------------------------------------------- unsigned char Get_NCT5523D_Reg(unsigned char REG) unsigned char Result; Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); Result = inportb(NCT5523D_DATA_PORT); Lock_NCT5523D(); return Result; //--------------------------------------------------------------------------- FWA8708-C / FWA8708-H User Manual...
-
Page 69: Watchdog Timer Configuration
NCT5523D_DATA_PORT (NCT5523D_BASE+1) //--------------------------------------------------------------------------- #define NCT5523D_REG_LD 0x07 //--------------------------------------------------------------------------- #define NCT5523D_UNLOCK 0x87 #define NCT5523D_LOCK 0xAA //--------------------------------------------------------------------------- unsigned int Init_NCT5523D(void); void Set_NCT5523D_LD( unsigned char); void Set_NCT5523D_Reg( unsigned char, unsigned char); unsigned char Get_NCT5523D_Reg( unsigned char); //--------------------------------------------------------------------------- #endif //__NCT5523D_H FWA8708-C / FWA8708-H User Manual... - Page 70 Nuvoton NCT5523D, program abort.\n"); return(1); WDTInitial(); WDTEnable(10); WDTDisable(); return 0; //--------------------------------------------------------------------------- void WDTInitial(void) unsigned char bBuf; Set_NCT5523D_LD(0x08); //switch to logic device 8 bBuf = Get_NCT5523D_Reg(0x30); bBuf &= (~0x01); Set_NCT5523D_Reg(0x30, bBuf); //Enable WDTO //--------------------------------------------------------------------------- FWA8708-C / FWA8708-H User Manual...
- Page 71 = Get_NCT5523D_Reg(0xF0); bBuf &= (~0x08); Set_NCT5523D_Reg(0xF0, bBuf); //count mode is second Set_NCT5523D_Reg(0xF1, NewInterval); //set timer //--------------------------------------------------------------------------- void WDTDisable(void) Set_NCT5523D_LD(0x08); //switch to logic device 8 Set_NCT5523D_Reg(0xF1, 0x00); //clear watchdog timer Set_NCT5523D_Reg(0x30, 0x00); //watchdog disabled //--------------------------------------------------------------------------- FWA8708-C / FWA8708-H User Manual...
- Page 72 NCT5523D_BASE = 0x2E; result = NCT5523D_BASE; ucDid = Get_NCT5523D_Reg(0x20); if (ucDid == 0xC4) //NCT5523D?? goto Init_Finish; } NCT5523D_BASE = 0x00; result = NCT5523D_BASE; Init_Finish: return (result); //--------------------------------------------------------------------------- void Unlock_NCT5523D (void) outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK); outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK); //--------------------------------------------------------------------------- FWA8708-C / FWA8708-H User Manual...
- Page 73 Lock_NCT5523D(); //--------------------------------------------------------------------------- void Set_NCT5523D_Reg( unsigned char REG, unsigned char DATA) Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); outportb(NCT5523D_DATA_PORT, DATA); Lock_NCT5523D(); //--------------------------------------------------------------------------- unsigned char Get_NCT5523D_Reg(unsigned char REG) unsigned char Result; Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); Result = inportb(NCT5523D_DATA_PORT); Lock_NCT5523D(); return Result; //----------------------------------------------------------------------- FWA8708-C / FWA8708-H User Manual...
Need help?
Do you have a question about the FWA8708-C and is the answer not in the manual?
Questions and answers