Related Manuals for IBASE Technology MBN802
Summary of Contents for IBASE Technology MBN802
- Page 1 MBN802 Networking Motherboards Atom™ processor C3758 ® With Intel User’s Manual Version 1.0 (June 2018)
- Page 2 No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”).
-
Page 3: Compliance
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm). • Lead (Pb) • Mercury (Hg) • Cadmium (Cd) • Hexavalent chromium (Cr6+) • Polybrominated biphenyls (PBB) • Polybrominated diphenyl ether (PBDE) MBN802 User Manual... -
Page 4: Important Safety Information
CAUTION There is a danger of explosion if the lithium-ion battery is replaced with an incorrect battery. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries by observing local regulations. MBN802 User Manual... -
Page 5: Warranty Policy
Software in use (such as OS and application software, including the version numbers) 3. If repair service is required, you can download the RMA form at http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and contact your distributor or sales representative. MBN802 User Manual... -
Page 6: Table Of Contents
System Function Connector (JP8) .......... 17 2.5.5 Digital I/O Port (JP10) ............. 19 2.5.6 Fan Power Connector (CPU_FAN1, SYS_FAN1, SYS_FAN2) .. 19 2.5.7 Console Port & USB 3.0 Ports (CN6) ........20 2.5.8 USB 2.0 Connector (F_USB1) ..........20 MBN802 User Manual... - Page 7 South Bridge Chipset Configuration ........42 Security Settings ................... 44 Boot Settings..................45 Save & Exit Settings................46 Appendix ...................... 47 I/O Port Address Map ................48 Interrupt Request Lines (IRQ) ............... 51 Watchdog Timer Configuration .............. 53 MBN802 User Manual...
-
Page 8: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Optional Accessories • Specifications • Overview • Dimensions... -
Page 9: Introduction
1.1 Introduction MBN802 series is specifically designed for the network security and management market. There are plenty of applications adopting network security or network management as listed below. Network Security Applications: • Firewall • Unified Threat Management (UTM) • Virtual Private Network (VPN) •... -
Page 10: Features
• MBN802 1.4 Optional Accessories IBASE provide optional accessories as follows. Please contact us or your dealer if you need any. • Console Cable (160 cm, PK1-51) • Riser Card (IPN104) MBN802 User Manual... -
Page 11: Specifications
1 x PCIe (x8) slot (4-lane) Environment • Operating: 0 ~ 60 °C (32 ~ 140 °F) Temperature • Storage: -20~ 80 °C (-4 ~ 176 °F) Relative 5 ~ 90% Humidity All specifications are subject to change without prior notice. MBN802 User Manual... -
Page 12: Overview
1.6 Overview Top View I/O View Name Name LED Indicators (from top to USB 3.0 Ports bottom: Status, HDD, Power) User Self-defined Button GbE LAN Ports (with GPI Signal) Reserved for 10 GbE SFP+ Console Port Transceivers MBN802 User Manual... -
Page 13: Dimensions
1.7 Dimensions Unit: mm MBN802 User Manual... -
Page 14: Chapter 2 Hardware Configuration
Chapter 2 Hardware Configuration The information provided in this chapter includes: • Memory Installation / Replacement • Information and locations of connectors... -
Page 15: Memory Installation / Replacement
4. Gently push the module in an upright position until the ejector tabs of the memory slot close to hold the module in place when the module touches the bottom of the slot. To remove the module, press the ejector tabs outwards with your fingertips to eject the module. MBN802 User Manual... -
Page 16: Setting The Jumpers
1 2 3 When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e. turned On. When a jumper cap is removed from two jumper pins, this jumper is open, i.e. turned Off. MBN802 User Manual... -
Page 17: Jumper & Connector Locations On Motherboard
2.3 Jumper & Connector Locations on Motherboard Motherboard: MBN802 MBN802 User Manual... -
Page 18: Jumpers Quick Reference
Connector Page CPU SV Mode Selection Clear CMOS Data Clear RTC Data AT & ATX Mode Selection Factory Use Only JP4, JP7, JP11 2.4.1 CPU SV Mode Selection (JP2) Function Pin closed Setting CPU SV Normal (default) MBN802 User Manual... -
Page 19: Clear Cmos Data (Jp3)
2.4.2 Clear CMOS Data (JP3) Function Pin closed Setting Normal (default) Clear CMOS MBN802 User Manual... -
Page 20: Clear Rtc Data (Jp5)
Hardware Configuration 2.4.3 Clear RTC Data (JP5) Function Pin closed Setting Normal (default) Clear RTC MBN802 User Manual... -
Page 21: At & Atx Mode Selection (Jp6)
2.4.4 AT & ATX Mode Selection (JP6) Function Pin closed Setting (default) MBN802 User Manual... -
Page 22: Connectors Quick Reference
SATA III Port CN1, CN2 GbE RJ45 LAN Port CN7, CN12 10 GbE SFP+ 2x1 Cage Connector CN4, CN5 User Self-defined Button (with GPI Signal) PCIe (x8) Connector PCIE1 LED Indicators LED10 Factory Use Only J11, J13, JP9 MBN802 User Manual... -
Page 23: Com2 Port (Cn3)
2.5.1 COM2 Port (CN3) Signal Name Signal Name VCC5 SOUT Ground 2.5.2 PM Bus Connector (J14) Signal Name Signal Name Ground DATA +3.3V MBN802 User Manual... -
Page 24: Sata Power Connector (J7, J10)
Hardware Configuration 2.5.3 SATA Power Connector (J7, J10) Signal Name Signal Name VCC5 Ground Ground VCC12 2.5.4 System Function Connector (JP8) JP8 provides light indicators of the computer activities and status. It provides interfaces for the following functions: MBN802 User Manual... - Page 25 The two pins make an external LED connector light for LAN bypass. Signal Name Signal Name BYPASS0_LED- • Bypass LED2 (Pins 11 and 12) The two pins make an external LED connector light for LAN bypass. Signal Name Signal Name BYPASS1_LED- MBN802 User Manual...
-
Page 26: Digital I/O Port (Jp10)
Hardware Configuration 2.5.5 Digital I/O Port (JP10) Signal Name Signal Name Ground VCC5 OUT1 OUT2 OUT3 2.5.6 Fan Power Connector (CPU_FAN1, SYS_FAN1, SYS_FAN2) SYS_FAN1 SYS_FAN2 CPU_FAN1 Signal Name Signal Name Ground Rotation detection +12V Rotation control MBN802 User Manual... -
Page 27: Console Port & Usb 3.0 Ports (Cn6)
2.5.7 Console Port & USB 3.0 Ports (CN6) Signal Name Signal Name Ground Ground 2.5.8 USB 2.0 Connector (F_USB1) Signal Name Signal Name Ground Ground MBN802 User Manual... -
Page 28: Chapter 3 Bios Setup
Chapter 3 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Security Settings •... -
Page 29: Introduction
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. MBN802 User Manual... -
Page 30: Main Settings
BIOS Setup 3.3 Main Settings BIOS Setting Description Sets the date. System Date Use the <Tab> key to switch between the data elements. Set the time. System Time Use the <Tab> key to switch between the data elements. MBN802 User Manual... -
Page 31: Advanced Settings
3.4 Advanced Settings This section allows you to configure, improve your system and allows you to set up some system features according to your preference. MBN802 User Manual... -
Page 32: Trusted Computing
Note: Your computer will reboot during restart in order to change state of the device. Schedule an operation for the security device. Pending operation Note: Your computer will reboot during restart in order to change the state of security device. MBN802 User Manual... -
Page 33: Pcie Link Configuration
3.4.2 PCIE Link Configuration BIOS Setting Description Select upper limit on link operational speed for PCI Express RootPort. PCIE x4 Link Speed Options: Auto, Gen1, Gen2, Gen3 MBN802 User Manual... -
Page 34: Nct5523D Super Io Configuration
BIOS Setup 3.4.3 NCT5523D Super IO Configuration BIOS Setting Description Sets Parameters of Serial Ports. Serial Port You can enable / disable the serial port and select Configuration an optimal settings for the Super IO device. MBN802 User Manual... - Page 35 IO=3F8h ; IRQ=3, 4, 5, 6, 7, 9. 10, 11, 12 • IO=2F8h ; IRQ=3, 4, 5, 6, 7, 9. 10, 11, 12 • IO=3E8h ; IRQ=3, 4, 5, 6, 7, 9. 10, 11, 12 • IO=2E8h ; IRQ=3, 4, 5, 6, 7, 9. 10, 11, 12 MBN802 User Manual...
- Page 36 IO=3F8h ; IRQ=3, 4, 5, 6, 7, 9. 10, 11, 12 • IO=2F8h ; IRQ=3, 4, 5, 6, 7, 9. 10, 11, 12 • IO=3E8h ; IRQ=3, 4, 5, 6, 7, 9. 10, 11, 12 • IO=2E8h ; IRQ=3, 4, 5, 6, 7, 9. 10, 11, 12 MBN802 User Manual...
-
Page 37: Hardware Monitor
Options: Disabled, 40°C, 45°C, 50°C, 55°C, Control 60°C, 65°C, 70°C These fields are the parameters of the hardware Temperatures / monitoring function feature of the motherboard. The Voltages values are read-only as monitored by the system and showing the PC health status MBN802 User Manual... -
Page 38: Lan Bypass Configuration
3.4.5 LAN Bypass Configuration BIOS Setting Description Normal: All LAN ports in Normal state. WDT mointor system hang & initiates a reboot. Bypass Quick Setting Bypass: All LAN ports in BYPASS during power-off or WDT initiates bypass. MBN802 User Manual... -
Page 39: Serial Port Console Redirection
Console Redirection Enables / Disables the Console Redirection. The settings specify how the host computer and the Console Recirection remote computer (which the user is using) will Settings exchange data. Both computers should have the same or compatible settings. MBN802 User Manual... -
Page 40: Console Port Redirection Settings
Options: 1, 2 Flow control can prevent data loss from buffer overflow. When sending data, if the receiving buffers are full, a “stop” signal can be sent to stop the data Flow Control flow. Options: None, Hardware RTS/CTS MBN802 User Manual... -
Page 41: Usb Configuration
3.4.8 USB Configuration BIOS Setting Description Enables / Disables Legacy USB support. • Auto disables legacy support if there is no USB Legacy USB Support device connected. • Disable keeps USB devices available only for EFI applications. MBN802 User Manual... -
Page 42: Csm Configuration
BIOS Setup 3.4.9 CSM Configuration BIOS Setting Description Controls Legacy/UEFI ROMs priority. Boot option filter Options: UEFI and Legacy, Legacy only, UEFI only Controls the execution of UEFI and Legacy PXE OpROM. Network Options: Do not launch, Legacy MBN802 User Manual... -
Page 43: Intel Rc Setup
3.5 Intel RC Setup MBN802 User Manual... -
Page 44: Processor Configuration
TM2 to be available. GV3 msut be available for Turbo. Enables / Disables CPU Turbo capability. This option Turbo only applies to EC2 and above. VT-d Enables / Disables VT-d. VT-x Enables / Disables VT-x. MBN802 User Manual... -
Page 45: System Event Log
3.5.2 System Event Log BIOS Setting Description Enables / Disables / Automatically sets up options. If System Errors Auto is selected, the enabling or disabling of errorsin the driver is skipped. MBN802 User Manual... - Page 46 Memory Elog Support Enables Disables memory error logging support. Parity Check Enables / Disables parity check. Enables / Disables correctable memory error Log Correctable Error logging support. Log Uncorrectable Enables / Disables uncorrectable memory error Error logging support. MBN802 User Manual...
- Page 47 Send system event signal on correctable error. Enables / Disables system error reporting on all PCIe System Error enumerated root ports, bridges and devices. Enables / Disables parity error reporting on all PCIe Parity Error enumerated root ports, bridges and devices. MBN802 User Manual...
- Page 48 WHEA EINJ ACPI 5.0 allows you to set error type WHEA Error Injection with address and vendor extensions. WHEA Logging Enables / Disables WHEA Logging of errors. WHEA PCIe Error Enables / Disables WHEA PCIe error injection. Injection MBN802 User Manual...
-
Page 49: South Bridge Chipset Configuration
3.5.3 South Bridge Chipset Configuration BIOS Setting Description SATA Configuration Configures of SATA controller. IQAT Configuration Hides IQAT device from an OS. 3.5.3.1. SATA Configuration MBN802 User Manual... - Page 50 BIOS Setting Description IQAT Hides IQAT device from an OS. Enables / Disables the setting of IQAT FUSECTL Set IQAT FUSECTL register. Enables / Disables the setting of 64B MRR/MPL in Set 64B MRR/MPL IQAT DevCtl register. MBN802 User Manual...
-
Page 51: Security Settings
3.6 Security Settings BIOS Setting Description Administrator Sets an administrator password for the setup utility. Password User Password Sets a user password. MBN802 User Manual... -
Page 52: Boot Settings
Setup Prompt Timeout 65535 (0xFFFF) means indefinite waiting. Bootup NumLock State Selects the keyboard NumLock state. Quiet Boot Enables / Disables Quiet Boot option. Sets the system boot order priorities for hard disk, Boot Option Priorities CD/DVD, USB, Network. MBN802 User Manual... -
Page 53: Save & Exit Settings
Exits system setup after saving the changes. Save Changes Resets the system after saving the changes. Reset Discard Changes and Resets system setup without saving any changes. Reset Restores / Loads defaults values for all the setup Restore Defaults options. MBN802 User Manual... -
Page 54: Appendix
Appendix This section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration. • I/O Port Address Map • Interrupt Request Lines (IRQ) • Watchdog Timer Configuration... -
Page 55: I/O Port Address Map
Communications Port (COM1) 0x000002F8-0x000002FF Communications Port (COM2) 0x0000B000-0x0000BFFF Intel(R) Atom(TM) processor C3000 product family PCIe Root Port 3 - 19A7 0x00000000-0x00000CF7 PCI Express Root Complex 0x00000D00-0x0000FFFF PCI Express Root Complex 0x00000070-0x00000077 System CMOS/real time clock 0x00000070-0x00000077 Motherboard resources MBN802 User Manual... - Page 56 Programmable interrupt controller 0x0000002C-0x0000002D Programmable interrupt controller 0x00000030-0x00000031 Programmable interrupt controller 0x00000034-0x00000035 Programmable interrupt controller 0x00000038-0x00000039 Programmable interrupt controller 0x0000003C-0x0000003D Programmable interrupt controller 0x000000A0-0x000000A1 Programmable interrupt controller 0x000000A4-0x000000A5 Programmable interrupt controller 0x000000A8-0x000000A9 Programmable interrupt controller 0x000000AC-0x000000AD Programmable interrupt controller MBN802 User Manual...
- Page 57 Address Device Description 0x000000B0-0x000000B1 Programmable interrupt controller 0x000000B4-0x000000B5 Programmable interrupt controller 0x000000B8-0x000000B9 Programmable interrupt controller 0x000000BC-0x000000BD Programmable interrupt controller 0x000004D0-0x000004D1 Programmable interrupt controller 0x0000A000-0x0000AFFF Intel(R) Atom(TM) processor C3000 product family PCIe Root Port 4 - 19A8 MBN802 User Manual...
-
Page 58: Interrupt Request Lines (Irq)
Intel(R) I211 Gigabit Network Connection IRQ 4294967167 IRQ 4294967168 ~ Intel(R) I211 Gigabit Network Connection #6 IRQ 4294967185 IRQ 4294967186 ~ Intel(R) I211 Gigabit Network Connection #4 IRQ 4294967203 IRQ 4294967204 Intel(R) USB 3.0 eXtensible Host Controller - 1.0 (Microsoft) MBN802 User Manual... - Page 59 PCIe Root Port 3 - 19A7 IRQ 4294967292 Intel(R) Atom(TM) processor C3000 product family PCIe Root Port 2 - 19A6 IRQ 4294967293 Intel(R) Atom(TM) processor C3000 product family PCIe Root Port 0 - 19A4 IRQ 4294967294 PCI Express Root Port MBN802 User Manual...
-
Page 60: Watchdog Timer Configuration
(NCT5523D_BASE) #define NCT5523D_DATA_PORT (NCT5523D_BASE+1) //--------------------------------------------------------------------------- #define NCT5523D_REG_LD 0x07 //--------------------------------------------------------------------------- #define NCT5523D_UNLOCK 0x87 #define NCT5523D_LOCK 0xAA //--------------------------------------------------------------------------- unsigned int Init_NCT5523D(void); void Set_NCT5523D_LD( unsigned char); void Set_NCT5523D_Reg( unsigned char, unsigned char); unsigned char Get_NCT5523D_Reg( unsigned char); //--------------------------------------------------------------------------- #endif //__NCT5523D_H MBN802 User Manual... - Page 61 (SIO == 0) printf("Can not detect Nuvoton NCT5523D, program abort.\n"); return(1); WDTInitial(); WDTEnable(10); WDTDisable(); return 0; //--------------------------------------------------------------------------- void WDTInitial(void) unsigned char bBuf; Set_NCT5523D_LD(0x08); //switch to logic device 8 bBuf = Get_NCT5523D_Reg(0x30); bBuf &= (~0x01); Set_NCT5523D_Reg(0x30, bBuf); //Enable WDTO //--------------------------------------------------------------------------- MBN802 User Manual...
- Page 62 //enable timer bBuf = Get_NCT5523D_Reg(0xF0); bBuf &= (~0x08); Set_NCT5523D_Reg(0xF0, bBuf); //count mode is second Set_NCT5523D_Reg(0xF1, NewInterval); //set timer //--------------------------------------------------------------------------- void WDTDisable(void) Set_NCT5523D_LD(0x08); //switch to logic device 8 Set_NCT5523D_Reg(0xF1, 0x00); //clear watchdog timer Set_NCT5523D_Reg(0x30, 0x00); //watchdog disabled //--------------------------------------------------------------------------- MBN802 User Manual...
- Page 63 Init_Finish; } NCT5523D_BASE = 0x2E; result = NCT5523D_BASE; ucDid = Get_NCT5523D_Reg(0x20); if (ucDid == 0xC4) //NCT5523D?? goto Init_Finish; } NCT5523D_BASE = 0x00; result = NCT5523D_BASE; Init_Finish: return (result); //--------------------------------------------------------------------------- void Unlock_NCT5523D (void) outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK); outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK); //--------------------------------------------------------------------------- MBN802 User Manual...
- Page 64 LD); Lock_NCT5523D(); //--------------------------------------------------------------------------- void Set_NCT5523D_Reg( unsigned char REG, unsigned char DATA) Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); outportb(NCT5523D_DATA_PORT, DATA); Lock_NCT5523D(); //--------------------------------------------------------------------------- unsigned char Get_NCT5523D_Reg(unsigned char REG) unsigned char Result; Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); Result = inportb(NCT5523D_DATA_PORT); Lock_NCT5523D(); return Result; //----------------------------------------------------------------------- MBN802 User Manual...
Need help?
Do you have a question about the MBN802 and is the answer not in the manual?
Questions and answers