HP PROLIANT ML350 G6 Maintenance And Service Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Server
  5. PROLIANT ML350 G6
  6. Maintenance and service manual

HP PROLIANT ML350 G6 Maintenance And Service Manual

Hide thumbs Also See for PROLIANT ML350 G6:
Table of Contents

Advertisement

Quick Links

See also: User Manual
HP ProLiant ML350 G6 Server
Maintenance and Service Guide
Abstract
This guide is for an experienced service technician. HP assumes you are qualified in the servicing of computer equipment and trained in recognizing
hazards in products with hazardous energy levels and are familiar with weight and stability precautions for rack installations.
Part Number: 513502-007
February 2011
Edition: 7
All manuals and user guides at all-guides.com

Advertisement

Table of Contents
loading

Related Manuals for HP PROLIANT ML350 G6

Summary of Contents for HP PROLIANT ML350 G6

  • Page 1 Abstract This guide is for an experienced service technician. HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels and are familiar with weight and stability precautions for rack installations.
  • Page 2 © Copyright 2009-2011 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

  • Page 3: Table Of Contents

    All manuals and user guides at all-guides.com Contents Customer self repair ........................5 Parts only warranty service ......................... 5 Illustrated parts catalog ....................... 16 Mechanical components ........................... 16 System components ..........................20 Removal and replacement procedures ................... 27 Required tools ............................27 Preparation procedures ..........................
  • Page 4 Integrated Management Log ........................76 Array Diagnostic Utility ..........................76 HP Insight Remote Support software ......................77 HP Insight Server Migration software for ProLiant ..................77 Component identification ......................78 Front panel components ........................... 78 Front panel LEDs and buttons ........................79 Rear panel components ..........................

  • Page 5: Customer Self Repair

    HP specifies in the materials shipped with a replacement CSR part whether a defective part must be returned to HP. In cases where it is required to return the defective part to HP, you must ship the defective part back to HP within a defined period of time, normally five (5) business days. The defective part must be returned with the associated documentation in the provided shipping material.
  • Page 6 HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di servizi o di assistenza HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo spedirà direttamente al cliente per la sostituzione.
  • Page 7 La mancata restituzione del componente può comportare la fatturazione del ricambio da parte di HP. Nel caso di riparazione da parte del cliente, HP sostiene tutte le spese di spedizione e resa e sceglie il corriere/vettore da utilizzare.
  • Page 8 Si, durante la fase de diagnóstico, HP (o los proveedores o socios de servicio de HP) identifica que una reparación puede llevarse a cabo mediante el uso de un componente CSR, HP le enviará dicho componente directamente para que realice su sustitución. Los componentes CSR se clasifican en dos categorías:...
  • Page 9 HP podrá cobrarle por el de sustitución. En el caso de todas sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la empresa de transporte que se utilice para dicho servicio.
  • Page 10 Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.
  • Page 11 All manuals and user guides at all-guides.com No caso desse serviço, a substituição de peças CSR é obrigatória. Se desejar que a HP substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço. Customer self repair 11...
  • Page 12 All manuals and user guides at all-guides.com Customer self repair 12...
  • Page 13 All manuals and user guides at all-guides.com Customer self repair 13...
  • Page 14 All manuals and user guides at all-guides.com Customer self repair 14...
  • Page 15 All manuals and user guides at all-guides.com Customer self repair 15...

  • Page 16: Illustrated Parts Catalog

    All manuals and user guides at all-guides.com Illustrated parts catalog Mechanical components Item Description Spare part Customer self repair number (on page 5) Access panel 511769-001 Mandatory DIMM baffle 511773-001 Mandatory Large redundant fan air baffle 511772-001 Mandatory Front bezel, rack model 511771-001 Mandatory Front bezel, tower model...
  • Page 17 Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If, however, you require that HP replace them for you, there may or may not be additional charges, depending on the type of warranty service designated for your product.
  • Page 18 Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.
  • Page 19 All manuals and user guides at all-guides.com Illustrated parts catalog 19...

  • Page 20: System Components

    All manuals and user guides at all-guides.com System components Item Description Spare part Customer self number repair (on page System components Hot-plug power supply — — a) AC, 460 W 511777-001 Mandatory b) AC, 750 W 511778-001 Mandatory c) AC, 1200 W 498152-001 Mandatory Fan assembly, 92-mm...
  • Page 21 All manuals and user guides at all-guides.com Item Description Spare part Customer self number repair (on page f) 2.26-GHz Intel® Xeon® processor E5520, 80W* ** 490073-001 Optional g) 2.40-GHz Intel® Xeon® processor E5530, 80W* ** 490072-001 Optional h) 2.53-GHz Intel® Xeon® processor E5540, 80W* ** 490071-001 Optional i) 2.66-GHz Intel®...
  • Page 22 All manuals and user guides at all-guides.com Item Description Spare part Customer self number repair (on page c) 4-GB PC3-10600 (DDR3-1333) (RoHS)* 501541-001 Mandatory Boards System board 511775-001 Optional Power supply backplane 511776-001 Optional SAS/SATA 8-bay hard drive expansion cage backplane board 511785-001 Optional assembly, SFF*...
  • Page 23 All manuals and user guides at all-guides.com Item Description Spare part Customer self number repair (on page Mandatory i) 750-GB, 15,000-rpm, hot-plug 461288-001 Mandatory j) 1-TB, 15,000-rpm, hot-plug 461289-001 Mandatory k) 1-TB, 7200-rpm, hot-plug 508011-001 Mandatory l) 2-TB, 7200-rpm, hot-plug 508010-001 m) 300-GB, 6G/s 586875-001...
  • Page 24 Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If, however, you require that HP replace them for you, there may or may not be additional charges, depending on the type of warranty service designated for your product.
  • Page 25 Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.
  • Page 26 All manuals and user guides at all-guides.com Illustrated parts catalog 26...

  • Page 27: Removal And Replacement Procedures

    Extend the server from the rack. If you are performing service procedures in an HP, Compaq branded, telco, or third-party rack cabinet, you can use the locking feature of the rack rails to support the server and gain access to internal components.

  • Page 28: Remove The Server From The Rack

    Disconnect the power cords. The system is now without power. Remove the server from the rack To remove the server from an HP, Compaq branded, telco, or third-party rack: Power down the server (on page 27). Extend the server from the rack.

  • Page 29: Server Warnings And Cautions

    All manuals and user guides at all-guides.com Server warnings and cautions Before installing a server, be sure that you understand the following warnings and cautions. WARNING: To reduce the risk of electric shock or damage to the equipment: Do not disable the power cord grounding plug. The grounding plug is an important safety •...

  • Page 30: Tower Foot

    All manuals and user guides at all-guides.com For operations involving removable media bay access, the media bay panel can be removed from the bezel. Tower foot To remove the component: Power down the server (on page 27). Remove the tower bezel ("Front bezel"...

  • Page 31: Rack Bezel

    All manuals and user guides at all-guides.com CAUTION: Do not operate the server with the access panel removed. Operating the server in this manner results in improper airflow and improper cooling that can lead to thermal damage. To remove the component: Power down the server (on page 27).

  • Page 32: Large Redundant Fan Air Baffle

    All manuals and user guides at all-guides.com Power down the server (on page 27). Remove the server from the rack (on page 28). Use a flat-head screwdriver to lift the spring tab. Slide the rail forward and remove it from the server. Repeat the steps above to remove the other rail.

  • Page 33: Dimm Baffle

    All manuals and user guides at all-guides.com Remove the large redundant fan air baffle. To replace the component, reverse the removal procedure. DIMM baffle To remove the component: Power down the server (on page 27). Do one of the following: Open or remove the tower bezel, as needed ("Front bezel"...

  • Page 34: Fan Blank

    All manuals and user guides at all-guides.com To replace the component, reverse the removal procedure. Fan blank To remove the component: Power down the server (on page 27). Do one of the following: Open or remove the tower bezel, as needed ("Front bezel"...

  • Page 35: Power Supply Blank

    All manuals and user guides at all-guides.com Remove the fan. To replace the component, reverse the removal procedure. Power supply blank To remove the component: Access the product rear panel ("Access the server rear panel (rack model)" on page 28). Remove the power supply blank.

  • Page 36: Hot-Plug Power Supply

    All manuals and user guides at all-guides.com Hot-plug power supply WARNING: To reduce the risk of electric shock, do not disassemble the power supply or attempt to repair it. Replace it only with the specified spare part. CAUTION: Do not attempt to remove and replace a power supply as a hot-plug procedure unless both bays are populated with power supplies.

  • Page 37: Sas/Sata Hard Drive

    All manuals and user guides at all-guides.com Remove the component as indicated. To replace the blank, slide the blank into the bay until it locks into place. SAS/SATA hard drive CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank.

  • Page 38: Standard Hard Drive Cage

    All manuals and user guides at all-guides.com Standard hard drive cage The procedure is the same for both the standard six-bay LFF hard drive cage and the standard eight-bay SFF hard drive cage. To remove the component: Power down the server (on page 27). Do one of the following: Open or remove the tower bezel, as needed ("Front...
  • Page 39 All manuals and user guides at all-guides.com NOTE: Remove the shipping screw, if installed, before removing the hard drive cage. Remove the hard drive cage. To replace the component: Using a T-15 Torx screwdriver, remove the sleeve from the spare hard drive cage. Removal and replacement procedures 39...

  • Page 40: Optional Two-Bay Lff Hard Drive Cage

    All manuals and user guides at all-guides.com Install the SFF hard drive cage into the server. Connect all cables to the spare hard drive cage. CAUTION: Always populate each media bay with either a device or a blank. Proper airflow can only be maintained when the bays are populated.
  • Page 41 All manuals and user guides at all-guides.com Remove the hard drive cage. To replace the component: Slide the spare hard drive cage about three-fourths of the way into the bay, leaving room to connect cables at the back of the drive cage. Connect all cables to the spare hard drive cage.

  • Page 42: Standard Hard Drive Cage Backplane

    All manuals and user guides at all-guides.com Slide the server back into the rack. Power up the server. Standard hard drive cage backplane To remove the component: Power down the server (on page 27). Do one of the following: Open or remove the tower bezel, as needed ("Front bezel"...

  • Page 43: Expansion Slot Cover

    All manuals and user guides at all-guides.com Eight-bay SFF hard drive cage backplane To replace the component, reverse the removal procedure. Expansion slot cover To remove the component: Do one of the following: Unlock and remove the bezel ("Front bezel" on page 29). Extend the server from the rack.

  • Page 44: Expansion Board

    All manuals and user guides at all-guides.com Remove the expansion slot cover. CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all PCI slots have either an expansion slot cover or an expansion board installed. To replace the component, reverse the removal procedure.

  • Page 45: Media Bay Blank

    All manuals and user guides at all-guides.com Push the release latches on the expansion board retainer, and then open the retainer. Remove the T-15 Torx screw securing the expansion board, if necessary. Remove the expansion board. To replace the component, reverse the removal procedure. Media bay blank To remove the component: Open or remove the tower bezel...

  • Page 46: Battery-Backed Write Cache Procedures

    All manuals and user guides at all-guides.com Remove the media bay blank. To replace the component, reverse the removal procedure. Battery-backed write cache procedures Two types of procedures are provided for the BBWC option: • Removal and replacement of failed components: Removing the cache module ("Battery-backed write cache module"...

  • Page 47: Bbwc Battery Pack

    All manuals and user guides at all-guides.com Remove the cache module. To replace the component, reverse the removal procedure. BBWC battery pack To remove the component: Power down the server (on page 27). Do one of the following: Open or remove the tower bezel, as needed ("Front bezel"...

  • Page 48: Recovering Data From The Battery-Backed Write Cache

    Set up a recovery server station using an identical server model. Do not install any internal drives or BBWC in this server. (HP recommends this option.) Find a server that has enough empty drive bays to accommodate all the drives from the failed server and that meets all the other requirements for drive and array migration.
  • Page 49 All manuals and user guides at all-guides.com CAUTION: Do not use this controller with cache modules designed for other controller models, because the controller can malfunction and you can lose data. Also, do not transfer this cache module to a different controller module, because you can lose data. Back up all data.

  • Page 50: Flash-Backed Write Cache Capacitor Pack

    All manuals and user guides at all-guides.com If the cache module is connected to a capacitor pack, disconnect the capacitor pack cable from the connector on the top of the cache module. To replace the component, reverse the removal procedure. CAUTION: To prevent damage to the cache module during installation, be sure the cache module is fully inserted before pressing down.

  • Page 51: Pci-X Expansion Cage

    All manuals and user guides at all-guides.com If the capacitor pack is connected to the cache module, disconnect the capacitor pack cable from the connector on the top of the cache module. Remove the capacitor pack. To replace the component, reverse the removal procedure. PCI-X expansion cage CAUTION: To prevent damage to the server or expansion boards, power down the server and...
  • Page 52 All manuals and user guides at all-guides.com Remove the four T-15 screws from the hard drive cage, and then slide the hard drive cage partially out of the chassis. Disconnect any external cables from the PCI-X expansion boards. Disconnect the power cable extension and the signal cable from the PCI-X expansion cage. Pull the spring-loaded locking pin out of its socket.

  • Page 53: Half-Height Or Full-Height Media Device

    All manuals and user guides at all-guides.com Remove the PCI-X expansion cage. Remove any expansion boards. To replace the components, reverse the removal procedure. Half-height or full-height media device To remove the component: Power down the server (on page 27). Do one of the following: Unlock and remove the bezel ("Front...
  • Page 54 All manuals and user guides at all-guides.com Disconnect data and power cables: Remove the device: Half-height Removal and replacement procedures 54...

  • Page 55: Dimm

    All manuals and user guides at all-guides.com Full-height To replace the component, reverse the removal procedure. IMPORTANT: Be sure to connect the right-angle end of the SATA data cable to the system board. Connecting it to the SATA drive may interfere with other installed media bay devices. IMPORTANT: If both SATA and PATA optical devices are installed simultaneously, only one can boot at a time.

  • Page 56: Heatsink

    All manuals and user guides at all-guides.com Remove the DIMM. To replace the component, reverse the removal procedure. For DIMM configuration information, see the server user guide. Heatsink To remove the component: Power down the server (on page 27). Do one of the following: Open or remove the tower bezel, as needed ("Front bezel"...
  • Page 57 All manuals and user guides at all-guides.com Remove the heatsink. To replace the component: Use the alcohol swab to remove all the existing thermal grease from the processor. Allow the alcohol to evaporate before continuing. Remove the heatsink protective cover. Install the heatsink.

  • Page 58: Processor

    All manuals and user guides at all-guides.com Close the heatsink locking levers. Install the large redundant fan air baffle, if removed. Install the access panel. Do one of the following: Close or install the tower bezel, as needed. Slide the server back into the rack. Processor The server supports single- and dual-processor operation.
  • Page 59 All manuals and user guides at all-guides.com Remove the heatsink. Open the processor locking lever and the processor socket retaining bracket. Using the processor tool, remove the processor from the system board: Line up the processor tool, ensuring the locking lever graphic on the tool is oriented correctly. Press in on the plastic tabs, and then place the tool on the processor.
  • Page 60 All manuals and user guides at all-guides.com Release the tabs, and then carefully lift the processor and tool straight up. Carefully rotate the tool, and then push in and release the tabs to secure the processor in the tool. CAUTION: To avoid damage to the processor, do not touch the bottom of the processor, especially the contact area.
  • Page 61 All manuals and user guides at all-guides.com Carefully insert the processor into the processor installation tool. Handle the processor by the edges only, and do not touch the bottom of the processor, especially the contact area. Removal and replacement procedures 61...
  • Page 62 All manuals and user guides at all-guides.com Be sure the tool is oriented correctly. Align the processor installation tool with the socket, and then install the processor. THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. CAUTION: THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED.
  • Page 63 All manuals and user guides at all-guides.com Press and hold the tabs on the processor installation tool to separate it from the processor, and then remove the tool. Close the processor socket retaining bracket and the processor locking lever. CAUTION: Be sure to close the processor socket retaining bracket before closing the processor locking lever.

  • Page 64: System Board

    All manuals and user guides at all-guides.com Close the heatsink locking levers. Install the large redundant fan air baffle, if removed. Install the access panel. Do one of the following: Close or install the tower bezel, as needed. Slide the server back into the rack. Power up the server.
  • Page 65 All manuals and user guides at all-guides.com Remove the heatsink ("Heatsink" on page 56). CAUTION: To avoid damage to the processor: Handle the processor only by the edges. • • Do not touch the bottom of the processor, especially the contact area. CAUTION: To avoid damage to the system board: Do not touch the processor socket contacts.
  • Page 66 All manuals and user guides at all-guides.com Line up the processor tool, ensuring the locking lever graphic on the tool is oriented correctly. Press in on the plastic tabs, and then place the tool on the processor. Release the tabs, and then carefully lift the processor and tool straight up. Carefully rotate the tool, and then push in and release the tabs to secure the processor in the tool.
  • Page 67 All manuals and user guides at all-guides.com Using the system board tray handles, slide the tray forward and remove the failed system board. To replace the component: Install the spare system board in the server before installing the processor. CAUTION: Failure to completely open the processor locking lever prevents the processor from seating during installation, leading to hardware damage.
  • Page 68 All manuals and user guides at all-guides.com Open the processor locking lever and the processor socket retaining bracket. Do not remove the processor socket cover. IMPORTANT: Be sure the processor remains inside the processor installation tool. If the processor has separated from the installation tool, carefully re-insert the processor in the tool. Handle the processor by the edges only, and do not touch the bottom of the processor, especially the contact area.
  • Page 69 All manuals and user guides at all-guides.com Align the processor installation tool with the socket, and then install the processor. THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. CAUTION: THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. To avoid damage to the system board: Never install or remove a processor without using the processor installation tool.
  • Page 70 All manuals and user guides at all-guides.com Press the tabs on the processor installation tool to separate it from the processor, and then remove the tool. Close the processor socket retaining bracket and the processor locking lever. The processor socket cover is automatically ejected.
  • Page 71 All manuals and user guides at all-guides.com Apply all the grease to the top of the processor in the following pattern to ensure even distribution. Install the heatsink. Close the heatsink locking levers. IMPORTANT: Install all components with the same configuration that was used on the failed system board.

  • Page 72: Power Supply Backplane

    All manuals and user guides at all-guides.com Select the Advanced Options menu. Select Service Options. Select Serial Number. The following warnings appear: WARNING! WARNING! WARNING! The serial number is loaded into the system during the manufacturing process and should NOT be modified. This option should only be used by qualified service personnel.

  • Page 73: Battery

    All manuals and user guides at all-guides.com Remove the power supply backplane. To replace the component, reverse the removal procedure. Battery If the server no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock.

  • Page 74: Hp Trusted Platform Module

    If you suspect a TPM board failure, leave the TPM installed and remove the system board ("System board" on page 64). Contact an HP authorized service provider for a replacement system board and TPM board. Removal and replacement procedures 74...

  • Page 75: Diagnostic Tools

    Configuring memory options • Language selection For more information on RBSU, see the HP ROM-Based Setup Utility User Guide on the Documentation CD or the HP website (http://www.hp.com/support/smartstart/documentation). HP Insight Diagnostics HP Insight Diagnostics is a proactive server management tool, available in both offline and online versions, that provides diagnostics and troubleshooting capabilities to assist IT administrators who verify server installations, troubleshoot problems, and perform repair validation.

  • Page 76: Hp Insight Diagnostics Survey Functionality

    For more information, see the Management CD in the HP Insight Foundation suite for ProLiant. Array Diagnostic Utility The HP Array Diagnostics Utility is a web-based application that creates a report of all HP storage controllers and disk drives. This report provides vital information to assist in identifying faults or conditions that may require attention.

  • Page 77: Hp Insight Remote Support Software

    HP strongly recommends that you install HP Insight Remote Support software to complete the installation or upgrade of your product and to enable enhanced delivery of your HP Warranty, HP Care Pack Service, or HP contractual support agreement. HP Insight Remote Support supplements your monitoring 24 x 7 to ensure maximum system availability by providing intelligent event diagnosis, and automatic, secure submission of hardware event notifications to HP, which will initiate a fast and accurate resolution, based on your product’s...

  • Page 78: Component Identification

    All manuals and user guides at all-guides.com Component identification Front panel components Item Description Power On/Standby button UID button USB connectors (2) Hot-plug hard drive bays (8-bay SFF drive cage model) Removable media bays Optical drive Component identification 78...

  • Page 79: Front Panel Leds And Buttons

    All manuals and user guides at all-guides.com Front panel LEDs and buttons Item Description Status System power LED Green = Power on Flashing green = Waiting for power due to group power capping Amber = System in standby, but power still applied Off = Power cord not attached or power supply failure Health LED Green = Normal...

  • Page 80: Rear Panel Components

    Serial connector Mouse connector ¹The SAS expander and the HP NC522SFP Dual Port 10GbE Server Adapter are not supported in slot 1. ²HP recommends the SAS expander is installed in slot 2. ³The HP NC522SFP Dual Port 10GbE Server Adapter is only supported in slot 3.

  • Page 81: Rear Panel Leds And Buttons

    All manuals and user guides at all-guides.com To support options beyond 75W, install the 150W PCIe video/graphics controller power cable option. Rear panel LEDs and buttons Item Description Status Power supply 2 LED Green = Power supply is on and functioning. Off = AC power is not available or AC power supply has failed.

  • Page 82: System Board Components

    System fan 4 connector System power connectors Processor 2 DIMM slots System fan 3 connector SD card slot (non-hot-plug) System maintenance switch Front panel LED board connector SAS connector B SAS connector A HP Smart Array P410i memory connector Component identification 82...
  • Page 83 Processor socket 1 System fan 1 connector ¹The SAS expander and the HP NC522SFP Dual Port 10GbE Server Adapter are not supported in slot 1. ²HP recommends the SAS expander is installed in slot 2. ³The HP NC522SFP Dual Port 10GbE Server Adapter is only supported in slot 3.

  • Page 84: System Board Leds

    All manuals and user guides at all-guides.com System board LEDs Item Description Status Power supply 1 Amber = No AC power or failed power supply Off = Power supply is on and functioning. Power supply 2 Amber = No AC power or failed power supply Off = Power supply is on and functioning.

  • Page 85: System Maintenance Switch

    All manuals and user guides at all-guides.com Item Description Status Processor 1 Amber = Processor 1 failed. Off = Processor 1 is functioning. System fan 1 Amber = Fan is missing or has failed. Off = Fan is functioning. Processor 1 DIMMs Amber = An error has occurred.

  • Page 86: Dimm Identification

    = 8-bit Memory speed 10600 = 1333-MHz 8500 = 1066-MHz DIMM type R = RDIMM (registered) E = UDIMM (unbuffered with ECC) For the latest supported memory information, see the QuickSpecs on the HP website (http://www.hp.com). Component identification 86...

  • Page 87: Sas/Sata Device Numbers

    All manuals and user guides at all-guides.com SAS/SATA device numbers • SFF configuration with an optional SAS expander • SFF configuration with a second SAS controller Component identification 87...

  • Page 88: Sas And Sata Hard Drive Leds

    All manuals and user guides at all-guides.com • LFF configuration SAS and SATA hard drive LEDs Item Description Fault/UID LED (amber/blue) Online LED (green) Component identification 88...

  • Page 89: Sas And Sata Hard Drive Led Combinations

    All manuals and user guides at all-guides.com SAS and SATA hard drive LED combinations Online/activity Fault/UID LED Interpretation LED (green) (amber/blue) On, off, or flashing Alternating amber The drive has failed, or a predictive failure alert has been received and blue for this drive;...

  • Page 90: Battery Pack Leds

    A fully-charged battery can normally preserve data for at least two days. The battery lifetime also depends on the cache module size. For further information, refer to the controller QuickSpecs on the HP website (http://www.hp.com). Double blink, then The cache microcontroller is waiting for the host controller to —...

  • Page 91: Fbwc Module Leds

    All manuals and user guides at all-guides.com LED3 pattern LED4 pattern Interpretation One blink per The battery pack is below the minimum charge level and is being — second charged. Features that require a battery (such as write cache, capacity expansion, stripe size migration, and RAID migration) are temporarily unavailable until charging is complete.

  • Page 92: Fan Locations And Configurations

    All manuals and user guides at all-guides.com Green LED Amber LED Interpretation Flashing (2 Hz) One of the following conditions exists: Flashing (2 Hz) Alternating with Alternating with • The charging process has timed out. green LED amber LED • The capacitor pack is not connected.
  • Page 93 All manuals and user guides at all-guides.com • Single-processor, standard fan configuration Item Description Rear fan 1 Rear fan 2 Front fan 3 Processor 1 DIMM baffle • Single-processor, redundant fan configuration Item Description Rear fan 1 Rear fan 2 Component identification 93...
  • Page 94 All manuals and user guides at all-guides.com Item Description Front fan 3 Front fan 4 Processor 1 DIMM baffle Large redundant fan air baffle • Dual-processor, non-redundant fan configuration Item Description Rear fan 1 Rear fan 2 Front fan 3 Processor 1 Processor 2 DIMM baffles...
  • Page 95 All manuals and user guides at all-guides.com • Dual-processor, redundant fan configuration Item Description Rear fan 1 Rear fan 2 Front fan 3 Front fan 4 Processor 1 Processor 2 DIMM baffles Large redundant fan air baffle Component identification 95...

  • Page 96: Optional Hard Drive Cage Jumper Location And Configuration Settings

    All manuals and user guides at all-guides.com Optional hard drive cage jumper location and configuration settings • Optional two-bay LFF backplane • Optional eight-bay SFF backplane Drive cage Installation Pin setting Standard No jumper Optional 1-2* *Optional drive cages ship with the jumper set across pins 1 and 2. Component identification 96...

  • Page 97: Specifications

    27.22 kg (60.00 lb) Weight (no drives installed) Power supply specifications Depending on installed options, the server is configured with one of the following power supplies: • HP ProLiant 1200 W Power Supply Specification Value Input requirements 100 to 120 VAC, 200 to...
  • Page 98 800 W at 100V AC input Maximum peak power 900 W at 120V AC input 1200 W at 200V to 240V AC input • HP ProLiant 750 W Power Supply Specification Value Input requirements 100 to 120 VAC, 200 to Rated input voltage...
  • Page 99 All manuals and user guides at all-guides.com 460 W at 100V to 120V AC input Maximum peak power 460 W at 200V to 240V AC input Specifications 99...

  • Page 100: Acronyms And Abbreviations

    All manuals and user guides at all-guides.com Acronyms and abbreviations Array Diagnostics Utility Advanced Memory Protection FBWC flash-backed write cache Integrated Lights-Out Integrated Management Log large form-factor LV DIMM Low voltage DIMM Native Command Queuing non-maskable interrupt PATA parallel ATA PCIe peripheral component interconnect express PCI-X...
  • Page 101 All manuals and user guides at all-guides.com POST Power-On Self Test ProLiant Support Pack RBSU ROM-Based Setup Utility RDIMM Registered Dual In-line Memory Module serial attached SCSI SATA serial ATA small form-factor Systems Insight Manager Server Migration Pack trusted platform module UDIMM Unregistered Dual In-Line Memory Module unit identification...

  • Page 102: Index

    LEDs 78, 79, 85, 89 customer self repair (CSR) 5 heatsink 56 HP Insight Diagnostics 75, 76 HP Insight Remote Support software 77 HP Insight Server Migration Pack software for device numbers 87 ProLiant 77 diagnostic tools 75 diagnostics utility 75...
  • Page 103 All manuals and user guides at all-guides.com ROM-Based Setup Utility (RBSU) 75 Large redundant air baffle 32 LED, health 78, 79 safety considerations 28 LED, system power 79 SAS drives 89 LED, UID 79, 81 SAS hard drive blank 36 LEDs 78, 88, 89 SATA hard drive 89 LEDs, front panel 79...

Table of Contents