1. Manuals
  2. Brands
  3. DINSEO Manuals
  4. Welding System
  5. DIX TIG GO 1406.M HF
  6. Operation manual

DINSEO DIX TIG GO 1406.M HF Operation Manual

Tig welding power source
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
BA-0134
Operations manual
TIG Welding Power Source
DIX TIG GO 1406.M HF
Keep in secure area for future reference!
S C H W E I S S E N
W E L D I N G
S C H W E I S S E N
S C H W E I S S E N
W E L D I N G

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DIX TIG GO 1406.M HF and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for DINSEO DIX TIG GO 1406.M HF

Summary of Contents for DINSEO DIX TIG GO 1406.M HF

  • Page 1 BA-0134 Operations manual TIG Welding Power Source DIX TIG GO 1406.M HF Keep in secure area for future reference! S C H W E I S S E N W E L D I N G S C H W E I S S E N...

  • Page 2: Table Of Contents

    Instructions for use TIG welding Description Electrode welding (MMA) DIX TIG GO 1406.M HF with digital control represents the very Maintenance latest evolution in direct current weld generators with INVERTER Optional technology. This powerful 100 KHz generator, based on the latest...

  • Page 3: Usage Limits (Iec 60974-1)

    The environment in which the equipment is installed must be suitable for the casing’s protection level. This system is cooled by means of the forced circulation of air, and Table 1 DIX TIG GO 1406.M HF Model TIG DC Single-phase power supply 50/60 Hz 1~230 ±20%...

  • Page 4: Connection To The Electrical Supply

    Table 2 DIX TIG GO 1406.M HF Model TIG DC Power input @ I Duty cycle @ X% (40°C) 200 (25%)* 160 (30%)* Supply connection cable Length Section Earth cable Section * Factor of efficiency must therefore be placed in such a way that the air may be easily sucked in and expelled through the apertures made in the frame.

  • Page 5: Electrode Welding (Mma)

    • With the welding power source switched off: 6a) Press the torch button. - Connect the ground cable to the snap-on connector 7a) The “Lift” function strikes the arc when the TIG torch electrode marked + (positive). comes into contact with the workpiece and is then removed - Connect the relative ground clamp to the workpiece or (Fig.
  • Page 6 Electrode welding (MMA) The welding electrode is used to weld most metals (various types steel, etc.),for which rutilic and basic electrodes are used. 1) Connecting the welding cables (Fig. F): Disconnect the welding power source from the mains power supply and connect the welding cables to the output terminals (Positive and Negative) of the welding power source, attaching them to the clamp and ground with the polarity specified for the type of electrode being used (Fig.

  • Page 7: Maintenance

    Digital interface PCB replacement Optional Proceed as follows: DIX TIG GO 1406.M HF welding power sources can be fitted with • Unscrew the 4 screws fastening the front rack panel. various remote control devices and accessories. • Remove the adjustment knob.

  • Page 8: Meaning Of Graphic Symbols On Welding Power Source

    Meaning of graphic symbols on welding power source Connector for the remote control Power supply switch System for use in environments with increased Warning! risk of electroshock Product suitable for free circulation in the Euro- Fast coupling TIG torch gas tube pean Community Before using the equipment you should carefully Danger! High voltage...

  • Page 10: Introduction

    Introduction Introduction Displaying the software version installed This manual describes the functions on and how to use the fol- Electrode welding (MMA) lowing control panels: TIG welding TIG welding with the SPOT WELDING function on TIG welding - Welding parameters Control panel Activating the VRD device DISPLAY...

  • Page 11: Displaying The Software Version Installed

    ■ WELDING MODE STANDARD TIG WELDING CONFIGURATION The welding machine offers 3 welding modes. Each time the but- When one of the 2 TIG welding processes available on the welding ton is pushed, the welding machine switches to select the weld- machine is activated, this allows you to select the following weld- ing mode indicated by the LED that stays lit, in the following order: ing parameters, based on which LED is flashing:...

  • Page 12: Tig Welding

    3) Turn the ENCODER KNOB (E) until the DISPLAY shows the 4) Turn the ENCODER KNOB (E) until the DISPLAY (D) shows PRINCIPAL welding CURRENT VALUE at which you wish to the CURRENT VALUE at which you wish to weld. weld, in relation to the diameter of the electrode you are us- ing.

  • Page 13: Tig Welding - Welding Parameters

    6) By pushing the WELDING PARAMETERS SELECTION (T3) Activating the VRD device key a number of times it is possible to set the various TIG WELDING PARAMETERS (see the “TIG Welding” paragraph To activate the VRD device, which must be done when the weld- - WELDING PARAMETERS).

  • Page 14: Auxiliary Functions

    All of this is necessary to allow our technical assistance depart- Auxiliary functions ment to resolve problems more easily, as quickly as possible and thanks to the user’s reports, also because, in the meantime the “Energy saving” machine will not allow the operator to do their work. This function manages correct functioning of the cooling fan that only runs when strictly necessary, that is: Table 1...

Table of Contents