Subscribe to Our Youtube Channel
Related Manuals for Microchip Technology CEC1x02
Summary of Contents for Microchip Technology CEC1x02
- Page 1 CEC1x02 Development Board User’s Guide Microchip Direct Order #DM990013 2018 Microchip Technology Inc. DS50002727A...
- Page 2 SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries.
-
Page 3: Table Of Contents
Chapter 2. Features ....................... 9 2.1 CEC1x02 Development Board Layout ............9 Chapter 3. Recommended Tools and Accessories ..........11 Chapter 4. Powering the CEC1x02 Development Board ......... 12 Chapter 5. Jumper Options ..................13 Chapter 6. Initial Hardware Setup ................15 Chapter 7. -
Page 4: Preface
Customer Support • Document Revision History DOCUMENT LAYOUT This document describes how to use the CEC1x02 Development Board as a development tool. The manual layout is as follows: • Chapter 1. “Introduction” – Shows a brief description of the CEC1x02 Develop- ment Board. -
Page 5: Conventions Used In This Guide
• Chapter 8. “Schematics” – CEC1x02 Development Board schematic diagrams. • Chapter 9. “Bill of Materials” – Provides the CEC1x02 Development Board Bill of Materials (BOM). CONVENTIONS USED IN THIS GUIDE This manual uses the following documentation conventions: DOCUMENTATION CONVENTIONS... -
Page 6: The Microchip Web Site
CEC1x02 Development Board User’s Guide THE MICROCHIP WEB SITE Microchip provides online support via our web site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: •... -
Page 7: Document Revision History
(FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://www.microchip.com/support DOCUMENT REVISION HISTORY Revision Section/Figure/Entry Correction DS50002727A (02-21-18) Document Release 2018 Microchip Technology Inc. DS50002727A-page 7... -
Page 8: Chapter 1. Introduction
CEC1x02 Development Board User’s Guide Chapter 1. Introduction The CEC1x02 Development Board is intended as a development, demonstration, and testing platform for Internet-of-Things applications using the CEC1702, a 32-bit ARM® Cortex®-M4-based microcontroller with additional security peripherals. The board fea- tures a variety of hardware options (including a power supply, user interface, serial communications, and expansion headers) that enable rapid prototyping and develop- ment of embedded, secure Internet-of-Things applications. -
Page 9: Chapter 2. Features
CEC1x02 Development Board User’s Guide Chapter 2. Features CEC1X02 DEVELOPMENT BOARD LAYOUT 1. USB micro-B connector — Provides power to the board and provides an inter- face for serial input/output or I2C using the Microchip MCP2221A USB-to-UART/I2C serial converter. 2. Power Adapter Plug — Provides another way to apply power to the board by external power adapter from 6 V to 16 V, such as AC002014 - 9 V Wall Mount Power Supply. - Page 10 CEC1x02 Development Board User’s Guide 10. Status Indication LED — Output LED for the CEC1702’s Blinking/Breathing LED hardware module. 11. 128x64 pixel LCD — EastRising ERC12864 SPI-interface LCD. Useful for dis- playing user application text/images. 12. JTAG Debugging headers — Provides a standard 20-pin header and a 1x6 header for flexibility.
-
Page 11: Chapter 3. Recommended Tools And Accessories
Microchip provides several free firmware projects and libraries that are compatible with the CEC1x02 Development Board. These demos show the basic functionality of the CEC1x02 Development Board and the CEC1702. Details on the usage of these exam- ple projects can be found in the documentation accompanying the projects. -
Page 12: Chapter 4. Powering The Cec1X02 Development Board
Chapter 4. Powering the CEC1x02 Development Board The CEC1x02 Development Board can be powered directly through the USB micro-B port of the USB-Serial converter (CN1). The 5 V input from the USB voltage rail is reg- ulated to 3.3 V by an MCP1755S voltage regulator. -
Page 13: Chapter 5. Jumper Options
CEC1x02 Development Board User’s Guide Chapter 5. Jumper Options The CEC1x02 Development Board has several jumpers, summarized as follows: Jumper Description Details KeyPad Header Connect to an external keypad up to 4x4 JTAG Header Standard 20 pin ARM®-JTAG Connec- tor. - Page 14 CEC1x02 Development Board User’s Guide The CEC1702PIM has several jumpers, summarized as follows: Jumper Description Details JTAG/SPI Header Shared header design is mated with MikroE's mikroProg for CEC program- ming/debugger device VCC_RST Grounded Put CEC1702 in reset for SPI flash pro-...
-
Page 15: Chapter 6. Initial Hardware Setup
User’s Guide Chapter 6. Initial Hardware Setup The CEC1x02 Development Board should have all the required jumpers installed for power up through the USB micro-B port (CN1). You can plug-in the USB micro-B Cable from the PC to the board and +3.3V power LED (LD5) should be turned on. -
Page 16: Chapter 7. Programming And Testing
Click on Detect MCU to display: CEC1702. d) Click on Load to load the binary file to program to SPI Flash. e) Click on Write to write binary file to SPI Flash. 2018 Microchip Technology Inc. DS50002727A-page 16... - Page 17 Open the Dediprog Software then select the SPI Flash chip ID: 26VF016B. Click OK. Please install SFv6.0.4.41 or later, older versions may not able to detect the Note: device. d) Options settings: Press the Config button. 2018 Microchip Technology Inc. DS50002727A-page 17...
-
Page 18: Testing
CEC1x02 Development Board User’s Guide e) Click on File to select test binary, for example: spi_image_led_lcd_lcdBack- light.bin from the sample project. Click Batch and it will start 'erase and program'. g) After the programming has completed successfully, remove jumper T1 on CEC1702 PIM board. -
Page 19: Chapter 8. Schematics
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 2 4 6 8 10 2 4 6 8 10 12 14 16 1 2 3 4 5 6 7 8 2018 Microchip Technology Inc. DS50002727A-page 19... -
Page 20: Cec1702Pim
CEC1x02 Development Board User’s Guide CEC1702PIM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 2 4 6 8 10 ... -
Page 21: Chapter 9. Bill Of Materials
CON HDR-2.54 Male 2x3 Gold 5.84 Samtec TSW-103-07-S-D mH TH VERT J6,J7,J8,J9 CON HDR-2.54 Male 1x16 Gold 5.84 Samtec TSW-116-07-G-S mH TH VERT J10,J11 CON HDR-2.54 Male 1x5 Gold 5.84 Samtec TSW-105-07-S-S mH TH VERT 2018 Microchip Technology Inc. DS50002727A-page 21... - Page 22 CEC1x02 Development Board User’s Guide Manufacturer Part Reference Description Manufacturer Number CON HDR-2 Male 1x2 SHROUDED EastRising ER-CON2.0-2P-SMD LOCK SMD RA CON HDR-2.54 Female 1x6 Gold TH Sullins PPPC061LGBN-RC JP1,JP2 CON HDR-2.54 Male 1x3 Tin 5.84 mH Samtec TSW-103-07-T-S TH VERT JP3,JP5,JP6 MECH HW JUMPER 2.54 mm 1x2...
-
Page 23: Cec1702Pim Development Board
IC LOGIC SN74LVC125ADBR Quad Bus CEC1702Q-C2-I/SX Buffer Gate SSOP-14 Y1 (DNP) CRYSTAL 32.768 kHz 12.5 pF SMD Seiko SC32S-12.5PF20PPM ABS07 C3,C4 (DNP) CAP CER 10 pF 50 V 5% NP0 SMD 0402 Murata GRM1555C1H100JZ01D 2018 Microchip Technology Inc. DS50002727A-page 23... -
Page 24: Worldwide Sales And Service
New York, NY Tel: 46-31-704-60-40 Tel: 631-435-6000 Sweden - Stockholm San Jose, CA Tel: 46-8-5090-4654 Tel: 408-735-9110 UK - Wokingham Tel: 408-436-4270 Tel: 44-118-921-5800 Canada - Toronto Fax: 44-118-921-5820 Tel: 905-695-1980 Fax: 905-695-2078 2018 Microchip Technology Inc. DS50002727A-page 24 10/25/17... - Page 25 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Microchip DM990013 DM990013-BNDL...
Need help?
Do you have a question about the CEC1x02 and is the answer not in the manual?
Questions and answers