B.E.G. LUXOMAT PD2-M-1C Installation And Operating Instruction

LUXOMAT
Installation and Operating Instruction for B.E.G. - Occupancy detectors PD2-M-1C-SM/-FC/-FM
1. Mounting preparations
Work on the 230 V mains supply
may only be carried out by qualified
professionals or by instructed persons
under the direction and supervision
of qualified skilled electrical person-
nel in accordance with electrotechni-
cal regulations.
Disconnect supply before installing!
When in Master/ Slave mode of
operation, the Master-appliance
must always be installed at the
location where there is least
daylight.
2d. Self test cycle
2000
1200
600
200
40
The product enters an initial 60-sec-
ond self-test cycle, when the supply
is first connected. The occupancy
detector is ready for operation.
Option:
max
IR-PD
ON
OFF
Wall bracket for remote
max
control IR-PD
ON
OFF
IR-PD-Mini
®
2a. Installation of the LUXOMAT
PD2-M-1C-SM
The detector must be in-
stalled on a solid and level
surface. There is no need
for frames.
For mounting remove lens
(C) (turn anticlockwise).
Fasten the mounting pod
to the ceiling.
Having connected up the wires in accordance
with regulations, secure the detector with 2
screws as per the illustration above. In order
to assemble the detector outside, the PD2-IP54
base-plate, which is available as an accessory,
must be mounted between the detector and the
surface on which it is to be installed.
120 60 50
A
40
3. Putting into operation / Settings 30
15
5
10
Follow-up time for light control
16 10
5
The time can be set infinitely variably at between
2
1
15 seconds and 16 minutes.
120 60 50
TEST 30
A 15
40
Symbol : impulse < 1sec.
30
15 TEST
Symbol : Test mode
5
10
2000
(Every movement switches on the light for a period of 1
1200
second, switching it off for a period of 2 seconds after that
600
16 10 200
regardless of the level of brightness.)
40 5
2
1
TEST
30
15
2000 Twilight-switch for light control (relay 1)
1200
The switch-on value for the light can be set at between 10
600
and 2000 Lux. Using the rotary control, the luminance set
200
40
points can be set as desired.
Symbol : Night-time operation
Symbol : Daytime / Night-time operation
Unlocking device
��
Luminance set point
��� ����
���
Automatic reading in the current light value
as new luminance set point
Individual light value 2 - 2500 Lux
��
Follow-up time (relay and channel 1)
��� ��
���
15 sec. up to 30 min.
50
1500
Lux Lux
Impulse function (relay and channel 1)
1sec. ON, 9 sec. OFF
Preset / user mode
Fully automatic/semi automatic mode => (see page 2, point 5)
Semi automatic: red LED (flashing),
Fully automatic: red LED on for approx. 3 sec.
50 1500
Lux Lux
Resetting when open
All values which have been programmed using the remote
control IR-PD are deleted, and those values which have
been set by potentiometer are activated.
Lock device
PD2-M-1C
® 2b. Installation of the LUXOMAT
PD2-M-1C-FC
Having connected up the cables in accor-
dance with regulations, the detector is
inserted into the opening as shown in the
drawing opposite and fixed into position with
the assistance of the spring clips.
max
ON
OFF
® 2c. Installation of the LUXOMAT
PD2-M-1C-FM
The detector has
been designed
and developed
specifically for instal-
lation in suspended
ceilings.
A circular opening of
diameter 68 – 70 mm
must be produced in
the ceiling.
then be locked into position with the assistance of
the spring clips.
4. Settings carried out using remote control (optional)
Remote control LUXOMAT IR-PD
120 60 50
A
40
30
15
5 1. Check Battery:
10
open battery compartment by pressing the
120 60 50
16 10
A plastic springs together and removing the
5
40
2
30 battery-holder.
1
15
5 10 TEST
30
15
1 2
2. IMPORTANT
16 10
2000
5
1200 Please pay attention, that the setting is Potentio-
2
600
1
meter 1 at "TEST" and Potentiometer 2 not at
200
TEST 30
15
40
"SUN". All values which have been programmed
120 60 50
A
40
using the remote control will be deleted in the
30
2000
15
5 1200 event of power failure in the position "TEST/
10
600
1 2
SUN". Please switch Potentiometer 2 over to
200
40
2000 "MOON" or any other value.
16 10
5
1200
2
600
1
200
TEST 30
15
40
Caution:
2000
1200
Settings with remote control supersede the
600
settings by courtesy of potentiometers.
200
40
Lock device
Test mode
Reset to deactivate
Resetting when closed
The lighting relay is switched off, i.e.
opened and the follow-up times reset.
Permanent protection against sabotage
This function blocks the unit permanently (green LED is illuminated).
This operating mode can only be activated during the period of 5
seconds after pressing the "lock" button. This status will only
permit actuating the function "Light on/Light off".
The procedure for leaving this mode is as follows:
1. Switch off the current
2. Apply current for 31 – 59 seconds
3. Switch of the current again
4. Apply current
50 1500
Lux
Lux 5. Open detector
Light on/off
The light will remain switched on/off for as long as movements
are detected in the areas of coverage. Once the last movement
has been detected, the light will remain on for the duration of the
follow-up time as per setting.
The appliance will then return independently to the mode selected
(Fully or Semi-automatic).
GB
®
The detector can be installed
in conventional inlet-sockets
mounted on the ceiling.
The assembly plate enclosed
must be stripped off prior to
installation and secured to the
ceiling using 4 screws and
ensuring that it is not laterally
transposed.
Having connected up the
cables in accordance with
regulations, the detector can
be placed in position as shown
in the drawing opposite and,
applying a little pressure, can