Priefert RC98AI Operating Instructions

Step 1: Screw air fitting into hole marked air supply at back of the Automatic Control Box (ACB) bolted to the top of roping chute.
Step 2: Connect air supply to fitting at the back of ACB. Set regulator on air compressor at 90 psi.
Step 3: Connect electrical cord to 110 volt outlet.
Proper performance requires a minimum of 2hp air compressor that will produce 3.1 cfm at 90 psi, with a 4 gallon tank.
NOTICE: Priefert Manufacturing Recommends using a dedicated Air Compressor to prevent damage from contamination to the
Compressed Air System. Use Clean & Dry Compressed Air Supply. Drain Compressor & Air Tanks Daily.
The Front buttons of the Remote operate
the Front Gate of the Roping Chute
Pressing this button will OPEN the
FRONT GATE of the Roping Chute
Pressing this button will OPEN the
REAR GATE of the Roping Chute
Robotic Mode
Using the button on the right rear of the Control Box, the chute
can be switched into the "Robotic" mode, where the chute uses
an electronic eye to detect the presence or absence of a steer.
A red light will appear. To release the steer, push the "Front / Open"
button on the upper left of the remote control. The headgate
opens and a few seconds after detecting that the steer has left,
the headgate closes; the tailgate then opens and upon detection
of the next steer having entered the chute, the tailgate closes.
One push of a single button has completed the entire cycle and
ropers have the next steer loaded and ready to go upon return to
the roping box. To take the chute out of auto mode, simply push the
button again on the back right side of the Control Box.
This chute also offers the operator the option to override the
Robotic mode and "score" his horse by opening and closing the
tailgate with the push of buttons. This will not take the chute out of
Robotic mode and continues to be a great training tool to keep your
horse from leaving the box at the sound of the chute rather than
from a cue from the rider.
1-800-527-8616
903-572-1741 903-572-2798 Fax
sales@priefert.com
OPMAN-RC98AI_0518
Operating Instructions (RC98AI)
Congratulations on your purchase of Priefert's new RC98AI Remote
Controlled Roping Chute. This is the "latest and greatest" in Roping Chutes.
In the fully automatic mode, by pushing one button to release the front gate,
the operator can set in motion the release of the steer in the chute and the
loading of another. If preferred, you may use the 4 buttons on the remote
control to command all actions of the chute yourself.
Roping Chute Hook-Up
SEE ATTACHED NOTICE
Roping Chute Operation
Another control feature located on the back left of the Control Box is
a "Delay" setting. Just to the right of the green "on" indicator light is
a silver knob used to activate and set the delay timing. Each click
to the right gradually delays the activation of the opening of the
headgate from 2-30 seconds. When no one else is around, this great
feature offers ropers improved practice opportunities by allowing the
roper/operator to be fully prepared before the steer is released.
Roping Chute
The Rear buttons of the Remote operate
the Rear Gate of the Roping Chute
Pressing this button will CLOSE the
FRONT GATE of the Roping Chute
Pressing this button will CLOSE the
REAR GATE of the Roping Chute
Delay Setting
Priefert's Calf Roping Chute
offers the same great features
as the Steer Roping Chute
but specifically directed at
guys and gals who like to
2630 S. Jefferson
P.O. Box 1540
Mt. Pleasant, TX 75456-1540
focus on calf roping.
(RCCALFA)