Philips TPM16.1E LA Service Manual page 16

EN 16 5. TPM16.1E LA
Item Item value
5 NVM VALUE
6 NVM STORE
7 NVM COPY TV to USB
8 NVM READ USB to TV
9 VIRGIN_MODE
10 ORT_MODE
11 DRMWARNING
12 AGEING MODE
13 CLR_TEMP_R
14 CLR_TEMP_G
15 CLR_TEMP_B
16 AUTO_COLOR
17 ADC_GAIN_R
18 ADC_GAIN_G
19 ADC_GAIN_B
20 ADC_OFFSET_R
21 ADC_OFFSET_G
22 ADC_OFFSET_B
23 YPBPR_PHASE
24 AUD_GAIN_LINEIN
25 AUD_GAIN_HDMI
26 AUD_GAIN_ATV
27 AUD_GAIN_DTV
28 AUD_GAIN_USB
29 AQ_INDEX
30 DUMP PQ FROM TV
31 LOAD PQ to TV
32 DUMP AQ FROM TV
33 LOAD AQ to TV
34 COPY BIN CHL to TV
35 COPY BIN CHL to USB
36 PANEL FLIP
37 TKGS Setting memu
38 Dolby Banner
39 EXIT_FACTORY
How to Exit the Factory mode
Use one of the following methods:
• Select EXIT_FACTORY from the menu and press the "OK"
button.
Note: When the TV is switched "off" by a power interrupt, or
normal switch to "stand-by" while in the factory mode, the TV
will show up in "normal operation mode" as soon as the power
is supplied again. The error buffer will not be cleared.
5.1.4 Customer Service Mode (CSM)
Purpose
The Customer Service Mode shows error codes and
information on the TVs operation settings.The call centre can
instruct the customer (by telephone) to enter CSM in order to
identify the status of the set.This helps the call centre to
diagnose problems and failures in the TV set before making a
service call.
The CSM is a read-only mode; therefore, modifications are not
possible in this mode.
Specifications
• Ignore "Service unfriendly modes".
• Line number for every
line (to make CSM language independent).
2016-Nov-11
Service Modes, Error Codes, and Fault Finding
Default value
32" 43"
0
Press OK
Press OK
Press OK
Off
On On
On Off
Off Off
128 128
128 119
128 126
Press OK
128 128
128 128
128 129
127 127
127 127
127 127
InValid
18
17
18
17
17
1 1
Press OK
Press OK
Press OK
Press OK
Press OK
Press OK
Off
Off
Off
Press OK
49" Description
Displays the value at the NVM address of item 5
Use this option to save the data of item 6 to NVM address of item 5
Use this to store the NVM data to the REPAIR folder of a FAT formatted USB memory
stick. The TV will write two files in the REPAIR folder of the memory stick. It will create
this folder if it does not exist. The items are "Channel list", "Personal settings", "Option
codes", "Display-related alignments" and "History list". In case the download to the
USB stick was not successful "Failure" will appear. In this case, check if the USB stick
is connected properly. Now the settings are stored onto the USB stick and can be
used to download onto another TV or other SSB. Uploading is of course only possible
if the software is running and if a picture is available. This method is created to be
able to save the customer's TV settings and to store them into another SSB.
Use this to store the NVM data from the USB memory stick to the TV. The TV will save
the two files which were created in item 8 to the NVM of the set. Use these options
when replacing a SSB. When "USB to TV Success" is displayed remove the power
and restart the TV
Use this to return the set to virgin mode. Depends whether the set has been used
already.
Off ORT mode
On Warning the data rights management
Off Use this for aging a new LCD panel
110 Red colour temperature setting
111 Green colour temperature setting
128 Blue colour temperature setting
PC: any pattern that has black and white, YPbPr: SMPTE bar (colour bar), any timing.
177 Red ADC gain
179 Green ADC gain
172 Blue ADC gain
127 Red ADC offset
127 Green ADC offset
127 Blue ADC offset
Not available for this chassis
Line-in audio gain
HDMI audio gain
Analogue TV audio gain
Digital TV audio gain
USB audio gain
3 Audio Quality index
Saves the picture quality data to a file "pq.bin" to the root of a FAT formatted USB
memory stick
Loads the picture quality data from a file "pq.bin" in to the TV
Saves the audio quality data to a file "AQ.bin" to the root of a FAT formatted USB
memory stick
Loads the audio quality data from a file "AQ.bin" in to the TV
Copy the USB channel list to TV
Copy the TV channel list to USB
Flip panel
TKGS Setting memu
Dolby Banner
Exits the Factory mode
• Set the screen mode to full
screen (all contents on screen is visible).
• After leaving the Customer Service Mode, the original
settings are restored.
• Possibility to use "CH+" or "CH-" for channel surfing, or
enter the specific channel number on the RC.
How to Activate CSM
To activate CSM, press the following key sequence on a
standard remote control transmitter: "123654" (do not allow the
display to time out between entries while keying the sequence).
After entering the Customer Service Mode, the following items
are displayed.
Note: Activation of the CSM is only possible if there is no (user)
menu on the screen!
Contents of CSM
• 1.1 Set Type This information is very helpful for a
helpdesk/workshop as reference for further diagnosis. In
this way, it is not necessary for the customer to look at the
rear of the TV-set. Note that if an NVM is replaced or is
initialized after corruption, this set type has to be re-written
to NVM.
back to
div.table