Advertisement
Quick Links
FP42UL
FP60UL
FLAT PANEL CART WITH OR
WITHOUT A PULL OUT SHELF
WARNING: FP42 carts are intended to hold monitors up to 75 lbs and FP60 carts
are intended to hold monitors up to 100 lbs. The use of a TV monitor weighing more
than that may result in instability causing possible injury. The top, middle and bottom
shelves are intended to hold equipment up to 50 lbs. on each shelf. The pull out
shelf on FP42MUL and FP60MUL is intended to support equipment up to 15 lbs.
PARTS LIST
Cart Models: FP42UL, FP42MUL, FP60UL & FP60MUL
Qty
Part#
Description
1
022-3065
Right Rear Leg Assembly
1
022-3066
Left Rear Leg Assembly
2
022-3067
Front Leg Assemblies
1
010-5778
Top Shelf - FP42 Models
010-5794
Top Shelf - FP60 Models
1
010-5135
Middle Shelf - FP42 Models
010-5795
Middle Shelf - FP60 Models
1
010-1892
Bottom Shelf - FP42 Models
010-5796
Bottom Shelf - FP60 Models
1
022-2827
Handle Assembly
1
022-3068
Monitor Bracket - FP42 Models
022-3091
Monitor Bracket - FP60 Models
2
010-4953
Hook Bars
2
010-4956
Stop Brackets
2
015-0017
5" Stem Casters w/o Lock
2
015-0018
5" Stem Casters with Lock
Pull Out Shelf Models :
FP42MUL & FP60MUL
Qty
Part#
Description
2
010-5783
Shelf Brackets - FP42 Models
010-5784
Shelf Brackets - FP60 Models
1
010-5782
Pull Out Shelf
1
030-1468
Left Outer Slide
1
030-1470
Right Outer Slide
2
030-1471
Inner Slides
Electrical Unit Models :
FP42UL-E5BK, FP42MUL-EBK,
FP60UL-E5BK & FP60MUL-E5BK
Qty
Part#
Description
1
E6 UNIT
6-Outlet Electrical Unit
FP42MUL
FP60MUL
Ref
Qty
AA
22
BB
24
CC
2
DD
2
EE
2
FF
4
GG
4
HH
8
II
4
JJ
2
1
1
1
HARDWARE LIST
Part#
Description
030-0300-10T
5/8" Square Head Bolts
030-0002
5/16-18 Hex Serrated Nuts
030-1349
5/16-18 x 3/4" Hex Hd Screws
SC1048B
1/4-20 x 45mm Bolts
030-0207
1/4-20 Serrated Flange Nuts
030-0401
5/8-18 x 1 1/2" Hex Head Screws
030-0411
5/16-18 Serrated Nuts
030-0304
1/4-20 X 5/8" Combo Truss Hd Screws
030-0865
#6 x 1/2" Button Pin-In Hd Screws
030-0354
10-32 x 1 1/2" Button Sockets Screws
010-1106
Hex Wrench
030-1352
1/8" Security Pin-In Driver Bit
044-2124
Courtesy Hardware Pack
This Pack Consists of:
(4) Metric M4 x 12 Screws
(4) Metric M4 x 30 Screws
(4) Metric M5 x 12 Screws
(4) Metric M5 x 30 Screws
(4) Metric M6 x 12 Screws
(4) Metric M6 x 35 Screws
(8) Small Washers
(20) Large Washers
(4) 5/8" Large Spacers
1
Advertisement
Related Manuals for Bretford FP42MUL
Summary of Contents for Bretford FP42MUL
- Page 1 The top, middle and bottom shelves are intended to hold equipment up to 50 lbs. on each shelf. The pull out shelf on FP42MUL and FP60MUL is intended to support equipment up to 15 lbs. PARTS LIST HARDWARE LIST Cart Models: FP42UL, FP42MUL, FP60UL &...
- Page 2 STEP 1 Position the top shelf onto the rear legs making sure the leg brackets are to inside of the shelf. LOOSELY secure the shelf to the legs using screws (AA) and bolts (BB). BRACKET TO THE INSIDE These side holes are used for installing the handle.
- Page 3 STEP 2 Slide the middle and bottom shelves onto the rear legs. Slide the front legs on. LOOSELY install hardware to each corner, remembering to leave access for the handle. Slide on middle shelf. Slide on bottom shelf. Slide on front legs. INSTALL HARDWARE TO EACH CORNER, OMIT HANDLE SIDE...
- Page 4 STEP 3 Install handle to either side of the cart using bolts (CC) and nuts (BB). STEP 4 Secure tube and top shelf together using screws (DD) and nuts (EE). NOW TIGHTEN ALL CART CORNER HARDWARE...
- Page 5 STEP 5 Push a caster into each leg insert. To ensure casters are securely in place, a rubber mallet may be used to tap them in place. NOTE: The locking casters MUST be installed on the same side as the handle. STEP 6 Attach the monitor bracket onto the front of the rear leg tubes as shown using bolts (FF) and nuts (GG).
- Page 6 SKIP TO STEP 12 IF YOUR CART DOES NOT HAVE A SHELF STEP 7 Attach each shelf bracket under the top shelf as shown using screws (HH). Make sure the bracket cutouts face this way, if not the bracket will be installed upside down.
- Page 7 STEP 9 Install each inner slide into the outer slides. NOTE: Push inner slide in all the way until it snaps in. STEP 10 Extend the slides to the positioning shown.
- Page 8 STEP 11 Install the pull out shelf by sliding CUTOUT 1 into TAB 1 and CUTOUT 2 into TAB 2. CUTOUT 2 TAB 1 TAB 2 CUTOUT 1...
- Page 9 STEP 12 Attach both hook bars onto the back of your monitor using the mounting holes built into the case. A courtesy hardware pack has been provided with several metric screw sizes. You may need to purchase additional metric screws from your local hardware store for odd shaped monitors. BOTTOM STEP 13 With someone’s help, hook your monitor onto the bracket as shown.
- Page 10 STEP 14 Attach the stop brackets to the hook bars as shown with security screws (II) using the driver bit provided. STEP 15 Center your monitor horizontally and then tighten in place with screws (JJ). CENTER MONITOR HORIZONTALLY THEN SECURE Part # 031-8665 Rev.