Advertisement
Quick Links
19" RACK PRESENTATION CART
WITH & WITHOUT POWER
Assembly Instructions
PARTS LIST
Qty
Part#
Description
2
022-2708
Leg Assembly Stamped with "X"
2
022-2709
Leg Assembly Stamped with "O"
1
022-2695
Top Shelf w/Grommet Hole
1
022-2699
Middle Shelf w/Grommet Hole
1
010-4791
Bottom Shelf
2
010-4785
Slide Bracket
2
030-1191
Slide
2
010-5053
Keyboard Shelf
1
010-4788
Front Panel
1
010-4789
Rear Panel
2
022-2697
Left Door Assembly
2
022-2698
Right Door Assembly
1pr.
030-1206
Rack Rail
4
010-4799
Rail Bracket
2
010-4867
Utility Shelf
2
015-0002
4" Caster w/o Brake
2
015-0003
4" Caster w/ Brake
1
E12
Electrical Unit - TC15FF ONLY
TC15 / TC15FF
HARDWARE LIST
Ref
Qty
Part#
AA
24
030-0300-10T
BB
24
030-0002
CC
36
030-0325
DD
16
030-0240
EE
16
030-1228
FF
8
030-1203
GG
10
02236
HH
4
030-0023
I I
4
030-0522
JJ
8
030-0256
KK
2
030-0302
MM
8
030-0402
NN
8
030-0383
1
010-1106
2
010-1188
4
012-0286
TOOLS REQUIRED
Hex Wrench (Provided)
Phillips Screwdriver
Rubber Mallet
Description
5/8" Square Head Bolts
5/16-18 Hex Serrated Nuts
1/4-20 x 1/2" Combo Screws
1/4" External Lockwashers
8-32 x 1/4" Combo Truss Hd Screws
#8-32 Acorn Nuts
8-32 Hex Flange Nuts
#6-32 x 3/8" Rnd Hd Machine Screws
6-32 Locknuts
1/4-20 Flange Nuts
#8-32 x 3/8" Screws - TC15FF ONLY
#10-32 x 5/8" Combo Screws
#10 x 1/2" "AB" Truss Hd Screws
Hex Wrench
Door Stop Brackets
Plastic Door Handles
1
Advertisement
Related Manuals for Bretford TC15
Summary of Contents for Bretford TC15
- Page 1 TC15 / TC15FF 19” RACK PRESENTATION CART WITH & WITHOUT POWER Assembly Instructions PARTS LIST HARDWARE LIST Qty Part# Description Ref Qty Part# Description 022-2708 Leg Assembly Stamped with “X” 030-0300-10T 5/8” Square Head Bolts 022-2709 Leg Assembly Stamped with “O” 030-0002 5/16-18 Hex Serrated Nuts 022-2695 Top Shelf w/Grommet Hole 030-0325 1/4-20 x 1/2” Combo Screws 022-2699 Middle Shelf w/Grommet Hole 030-0240 1/4” External Lockwashers 010-4791 Bottom Shelf 030-1228 8-32 x 1/4” Combo Truss Hd Screws 010-4785 Slide Bracket 030-1203 #8-32 Acorn Nuts 030-1191...
- Page 2 FIGURE 2 FIGURE 1 Bracket MUST Holes MUST fit INSIDE be ALIGNED shelf STEP 1 Lay the rear legs on a carpeted surface exactly as shown in FIGURE 1. Slide bottom and middle onto the legs so that the brackets are inside the shelves as shown in FIGURE 2. Holes MUST be ALIGNED STEP 2 Slide the front legs onto the shelves so that the brackets are inside the shelves as shown. NOTE: Make sure all bracket holes are aligned with the shelf holes.
- Page 3 FULLY TIGHTEN THESE ON BOTH SIDES ONLY INSTALL IN STEP 3 THESE LOCATIONS BOTH SIDES HAND TIGHTEN shelves and legs with bolts (AA) and nuts (BB). ONLY install side hardware and middle shelf hardware as indicated. FULLY TIGHTEN MIDDLE SHELF HARDWARE. STEP 4 Insert each caster into the bottom of each leg. If caster does not insert easily, use a rubber mallet to tap caster in place. Once caster are SECURELY in place, stand unit upright.
- Page 4 MIDDLE SHELF ATTACHMENT BOTTOM SHELF ATTACHMENT STEP 5 Attach L-brackets to one side of the cart. These should be mounted on the side that you wish the utility shelves to be installed on. Attach each bracket (2 per shelf) with screws (CC) and nuts (JJ) as shown.
- Page 5 MIDDLE SHELF ATTACHMENT BOTTOM SHELF ATTACHMENT STEP 6 Attach the rack rails to the L-brackets with screws (CC) and nuts (JJ) as shown. The threaded holes (smaller) are facing out. NOTE, THE RACK RAIL MUST BE INSTALLED AS SHOWN. CORRECT INCORRECT TOP DOWN VIEW OF INSIDE CART...
- Page 6 NOTE: Separate slides by pulling on black tab. STEP 7 Separate each slide and attach outer slide piece (2 per bracket) to the slide brackets using screws (EE) and nuts (FF) as shown. NOTE: Slide may need to be extended some to align attachment holes. STEP 8 Attach each slide bracket using screws (CC) and washers (DD) as shown.
- Page 7 STEP 9 Attach inner slide piece to keyboard shelf with screws (EE), washers (DD) and nuts (GG). STEP 10 Attach door stop brackets to both side of the bottom shelf with screws (HH) and nuts (I I) as shown.
- Page 8 Panel bottom flange MUST hook onto bottom shelf STEP 11A Carefully, lay cart down as shown and slide on front panel (the one without the grommet hole). Make sure panel’s bottom flange hooks onto the bottom shelf. NOTE: Rear panel (the one with a grommet hole) goes on the same side of the cart as the grommet hole in the middle shelf. STEP 11B Attach side panel in each corner with bolts (AA) and nuts (BB). HAND TIGHTEN FOR NOW. ONCE THESE STEPS ARE COMPLETE REPEAT THEM FOR THE REAR PANEL. STEP 11C Carefully, stand cart up and then from INSIDE the cart, attach side panel to legs using screws (CC) as shown.
- Page 9 STEP 12 Slide top shelf onto cart as shown. Secure all 4 corners with bolts (AA) and nuts (BB). NOW TIGHTEN ALL CORNER BOLTS AND NUTS ON THE ENTIRE CART. STEP 13 - FOR TC15FF MODELS ONLY Attach the UCSE10 unit to rear panel as shown using screws (KK) and nuts (GG).
- Page 10 STEP 14 Attach the utility shelves to the rack rails as shown with screws (MM). NOTE: You can install the shelves in any desired location along the rails. STEP 15 Attach a handle to each door using screws (NN) as shown.
- Page 11 STEP 16 Attach the doors to each side of the cart using screws (CC) as shown. STEP 17 Slide both keyboard drawers into the cart. Part # 031-7463 Rev. 08.13.10 CZ...