Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dynamic Engineering PMC-UNIV-TEST
Summary of Contents for Dynamic Engineering PMC-UNIV-TEST
- Page 1 DYNAMIC ENGINEERING 150 Dubois St. Suite C, Santa Cruz, CA 95060 831-457-8891 Fax 831-457-4793 http://www.dyneng.com sales@dyneng.com Est. 1988 User Manual PMC-UNIV-TEST PMC-UNIV-TEST-ENG Revision A1 Revised 9/24/18 Corresponding Hardware: Revision A Fab numbers: 10-2018-1201...
- Page 2 Dynamic Engineering has made every effort to ensure that this manual is accurate and complete. Still, the company reserves the right...
-
Page 3: Table Of Contents
PMC Module Backplane IO Interface Pin Assignment Construction and Reliability Thermal Considerations WARRANTY AND REPAIR Service Policy Out of Warranty Repairs For Service Contact: SPECIFICATIONS ORDER INFORMATION List of Figures FIGURE 1 PMC-UNIV-TEST PN4 INTERFACE STANDARD Embedded Solutions Page 3... -
Page 4: Product Description
The devices are for test support. Testpoints for the PCI bus plus JTAG are provided on both versions. In a PCI position, the B side is forward the A side is the rear. PMC-UNIV-TEST has the Host/carrier side connectors mounted to the A side. The PMC will have it’s main component side forward in this configuration. - Page 5 PMC-UNIV-TEST-ENG has some modifications when compared with the standard version. The B side PMC type connectors are added, the SCSI is removed, and the testpoints are moved to the opposite side. In this configuation the PMC side connectors can be installed into the host board, and the PMC can be installed into the carrier connectors on the A side [now facing up].
-
Page 6: Headers And Testpoints
Headers and TestPoints 56 testpoints are supplied each labeled with the PCI signal attached. Some names are truncated to allow larger easier to read print. JTAG TRST, TDI, TDO, TMST, TCK plus a 3.3V and a Ground reference to interface with the installed PMC via the JTAG signals. -
Page 7: Pmc Module Backplane Io Interface Pin Assignment
Pn4 to the PCIeBPMCX1 connectors. Also see the User Manual for your PMC board for more information. SCSI II [P2] Open Open FIGURE 1 PMC-UNIV-TEST PN4 INTERFACE STANDARD Read table: P2-1 = Pn4-3 P2-35 = Pn4-1 etc. Signals are matched length and differentially routed with 100 ohm impendance... -
Page 8: Construction And Reliability
Construction and Reliability PMC-UNIV-TEST is constructed out of 0.062 inch thick high temp RoHS compliant FR4 material. Surface mounted components are used. The connectors are SMT for the PMC bus and through hole for the testpoints and IO. The PMC Module connectors are keyed and shrouded with Gold plated pins on both plugs and receptacles. -
Page 9: Warranty And Repair
For service on Dynamic Engineering Products not purchased directly from Dynamic Engineering contact your reseller. Products returned to Dynamic Engineering for repair by other than the original customer will be treated as out-of-warranty. -
Page 10: Specifications
Specifications Logic Interfaces: PCI 32 bit Universal Voltage. Access types: All PCI supported CLK rates supported: 25-66 [likely work at higher rates as PCI signals are matched and controlled. ] Software Interface: Passive, no SW required for adapter Testpoints: PCI signals plus JTAG and grounds Interface: PMC front bezel directly, rear IO via SCSI connector. -
Page 11: Order Information
68 pin SCSI II to 68 screw terminal converter with DIN rail mounting. HDEcabl68 http://www.dyneng.com/HDEcabl68.html SCSI cables with latch blocks or thumbscrews and various lengths are available. Custom lengths can be ordered. All information provided is Copyright Dynamic Engineering Embedded Solutions Page 11...
Need help?
Do you have a question about the PMC-UNIV-TEST and is the answer not in the manual?
Questions and answers