Table of Contents
Advertisement
Quick Links
Video Pipe Inspection System
Your Gen-Eye Micro-Scope2 Video Pipe
Inspection System is designed to give you
years of trouble-free, profitable service.
However, no machine is better than its op-
erator.
Read, understand and follow all safety
warnings and instructions provided with the
product. Failure to follow the warnings and
instructions may result in electric shock
and/or serious injury. Save all warnings and
instructions for future reference.
SAVE THESE INSTRUCTIONS!
Gen-Eye Micro-Scope2
Operating Instructions
®
Advertisement
Table of Contents
Related Manuals for General Pipe Cleaners Gen-Eye Micro-Scope2
Summary of Contents for General Pipe Cleaners Gen-Eye Micro-Scope2
- Page 1 Gen-Eye Micro-Scope2 ® Video Pipe Inspection System Operating Instructions Your Gen-Eye Micro-Scope2 Video Pipe Inspection System is designed to give you years of trouble-free, profitable service. However, no machine is better than its op- erator. Read, understand and follow all safety warnings and instructions provided with the product.
-
Page 2: Safety Symbols
Always wear safety glasses rubber soled, non-slip dures for the Gen-Eye Micro-Scope2 shoes. Use of this safety equip- Video Pipe Inspection System. ment may prevent serious injury. SAFETY SYMBOLS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. -
Page 3: General Safety Rules
® Gen-Eye Micro-Scope2 Video Pipe Inspection/Location System Do not overreach. Keep proper footing and balance at all GENERAL SAFETY RULES times. Proper footing and balance enables better control of the tool in unexpected situations. WARNING Always wear safety glasses and rubber soled, non-slip Read and understand all instructions. -
Page 4: Specific Safety Rules
® Gen-Eye Micro-Scope2 Video Pipe Inspection/Location System SPECIFIC SAFETY RULES FEATURES Keep the device out of the reach of children. Top View: Do not look directly into the camera lens at the end of the Probe Rod Connector probe rod. Your eyesight may be seriously damaged. - Page 5 Brightness, Contrast, and Grey scale of free space on a storage device) Video Play and Pause icons GEN-EYE MICRO-SCOPE2 COMMAND MODULE The Command Module should not be used in wet locations or in the Video fast-forward and fast-rewind rain, as moisture may cause damage to the unit.
- Page 6 ® Gen-Eye Micro-Scope2 Video Pipe Inspection/Location System Main Display (Row 2) Set the clock (hours, minutes, seconds). Use the UP and DOWN arrow buttons to select the hours, minutes, and seconds The main display appears as shown. field and use the VIDEO (increase) and PHOTO (decrease) but- Camera image area tons to set the time.
- Page 7 ® Gen-Eye Micro-Scope2 Video Pipe Inspection/Location System Video Recording, Viewing and Deleting Power Input Power input is located on the left side of the Command Module. Only NOTE: The Gen-Eye Micro-Scope is equipped with an integral micro- operate the Micro-Scope2 with the 15 volt power supply supplied with phone.
- Page 8 ® Gen-Eye Micro-Scope2 Video Pipe Inspection/Location System CAMERA REEL Make sure you have established live image on the monitor prior to recording. Use the ZOOM IN or ZOOM OUT buttons as re- Lengths quired to capture the image needed. You can also use the MIR-...
-
Page 9: Maintenance
® Gen-Eye Micro-Scope2 Video Pipe Inspection/Location System No Picture, Lights OK MAINTENANCE Check Monitor power switch is ON. Check to make sure the DISCONNECT MACHINE FROM POWER SOURCE power source is “live” (for 120 volt AC) or that the battery is BEFORE PERFORMING MAINTENANCE ON MACHINE! charged. - Page 10 ® Gen-Eye Micro-Scope2 Video Pipe Inspection/Location System TROUBLESHOOTING, continued Battery Won’t Hold Charge NOTE: Command Module is shipped without a charge. Charge the Command Module for 12 hours or overnight before first use. Allow 5 hours to fully recharge battery.