General Specifi Cations; Notice Special Requirements; Inspect/Prepare Installation Site; Clearances To Burner And Appliance - Beckett AFII 100 Manual

General Specifi cation
•
Table 1 – Burner Specifi cations
Capacity 'HLX' Heads
Firing rate:
Input: Min./Max - 56,000 /210,000 Btu/h
'FBX' Heads
Firing rate:
Input: Min./Max. - 56,000/189,000 Btu/h
Certifi cation/ UL certifi ed to comply with ANSI/UL296 &
Approvals tested to CSA B140.0
Fuels U. S No. 1 or No. 2 heating oil only (ASTM
Canada No. 1 stove oil or No. 2 furnace oil
Electrical Power supply - 120 volts AC, 60 Hz, single
phase
Operating load - 5.8 Amps max
Motor - 1/7 hp, 3450 rpm, NEMA 48M
frame PSC rotation CCW when
facing shaft end
Ignition - Continuous duty solid-state igniter
Fuel pump Outlet pressure - Note 1
Air tube ATC code - See Table 2
Dimensions Height (maximum) - 13 inches
(with cover) Width (maximum) - 14 inches
Depth
Air tube diameter
*
Note 1. See appliance manufacturer's burner specifi cations for
recommended outlet pressure.
Table 2 – Air Tube Combinations (ATC) & Dimensions
ATC codes for usable air tube lengths dim. "A" (Figure 3)
3"
HLX30 HLX50
HLX30 HLX50
HLX30 HLX50
HLX30 HLX50
FBX30 FBX50
FBX30 FBX50
FBX30 FBX50
FBX30 FBX50
HB 6 slot
RWB 6104 BAFII R01
- 0.40 – 1.50 GPH
- 0.40 – 1.35 GPH
D396)
only
- 6-11/16 inches
- 3-1/2 inches
5" 7" 9"
HLX70 HLX90
HLX70 HLX90
HLX70 HLX90
HLX70 HLX90
FBX70 FBX90
FBX70 FBX90
FBX70 FBX90
FBX70 FBX90
HC 9 slot

Notice Special Requirements

•
For recommended installation practice in Canada,
refer to the latest version of CSA Standard B139 &
B140.
Concealed damage — If you discover damage to
the burner or controls during unpacking, notify the
carrier at once and fi le the appropriate claim.
When contacting Beckett for service information —
Please record the burner serial number (and have
available when calling or writing). You will fi nd the
serial number on the silver label located on the left
rear of the burner. Refer to Figure 1.

Inspect/Prepare Installation Site

Clearances to Burner and Appliance

•
Provide space around burner and appliance for
ease of service and maintenance. Check the mini-
mum clearances against those shown by the ap-
pliance manufacturer and by applicable building
codes.
ATC Code Head
HB AF2-6 0.4-0.85 gph
HC AF2-9
HD AF2-6 0.40-0.85 gph
HE AF2-9
HFXS FB0 0.40-0.65 gph
HGXS FB3 0.55-0.85 gph
HHXS FB4
HIXS FB6
HD 6 slot
General Information
Firing rate range (gph)Min-Max
AFII 85 AFII 100
0.65-1.00 gph
N/A 0.65-1.00 gph
0.65-1.00 gph
N/A 0.65-1.00 gph
0.55-0.75 gph
0.55-1.10 gph
N/A 0.75-1.10 gph
N/A 0.85-1.15 gph
HE 9 slot
AFII 150
0.75-1.35 gph
0.75-1.50 gph
0.75-1.10 gph
0.75-1.35 gph
0.75-1.00 gph
0.85-1.20 gph
1.10-1.25 gph
1.15-1.35 gph
Page 5