Subscribe to Our Youtube Channel
Related Manuals for IOGear GHSW8441
Summary of Contents for IOGear GHSW8441
- Page 1 Quick Start Guide 4/8-Port 4K HDMI Switch GHSW8441 / GHSW8481 PART NO. Q1529 www.iogear.com...
-
Page 2: Package Contents
RS-232 or IR remote control. The front panel’s LEDs indicate the source device selected for the display at a glance. The GHSW8441/GHSW8481 supports True 4K of 4096 x 2160 @ 60Hz (4:4:4), the newest resolution for high definition displays;... - Page 3 Overview - GHSW8441 6. HDMI Output Port 1. HDMI Input Port 7. HDMI Input Ports 2. Port Selection Switch 8. RS-232 Serial Port 3. Port LEDs 9. On/Off Auto Switch 4. IR Receiver 5. Power Jack 10. IR Extension Port...
- Page 4 Overview - GHSW8481 1. Port Selection Push Buttons 6. On/Off Auto Switch 2. Power Button 7. HDMI Output Port 3. Power LED 8. HDMI Input Ports 4. Port LEDs 9. IR Extension Port 5. Power Jack 10. RS-232 Serial Port HDMI OUT...
- Page 5 IR Remote Control 11. Port Up/Down Buttons 12. Power On/Off Buttons 13. Port Selection Buttons HDMI IN...
-
Page 6: Hardware Installation
1. Use an HDMI cable to connect to the HDMI input port of the video display to the HDMI output port on the rear of the GHSW8441. 2. Use HDMI cables to connect to the HDMI output ports on the source devices to the HDMI input ports on the GHSW8441. - Page 7 Hardware Installation (Optional) 3. To edit the GHSW8441/GHSW8481 system settings through the RS-232 port for hardware or software configuration. RS-232 Serial Interface The GHSW8441’s built-in bi-directional RS-232 serial interface allows for system control from a high-end controller or from a PC.
- Page 8 Hardware Installation 5. Plug the power adapter cable into the Power Jack of the GHSW8441/GHSW8481.
-
Page 9: Operation
Operation Source Device Selection The GHSW8441/GHSW8481 HDMI Switch offers a variety of methods for source device selection from the front panel using pushbuttons, IR remote or through an RS-232 serial interface. Manual Selection To select a source device, press the port selection button that corresponds to the port that it is connected to. - Page 10 Operation Powering Off and Restarting If you power off the GHSW8441/GHSW8481, following the steps below before powering it again 1. Power off the attached devices 2. Unplug the power adapter cable from the GHSW8441/GHSW8481 3. Wait 10 seconds and then plug the power adapter cable back in.
-
Page 11: Compliance Information
Compliance Information WARNING: This product may expose you to chemicals including styrene which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. -
Page 12: Limited Warranty
Important Product Information Product Model Serial Number Contact WE’RE HERE TO HELP YOU! NEED ASSISTANCE SETTING UP THIS PRODUCT? Make sure you: 1. Visit www.iogear.com for more product information 2. Visit www.iogear.com/support for live help and product support IOGEAR https://iogear.custhelp.com support@iogear.com www.iogear.com...
Need help?
Do you have a question about the GHSW8441 and is the answer not in the manual?
Questions and answers