Texas Instruments CC2531 User Manual
Usb hardware
Hide thumbs
Also See for CC2531:
- Quick start manual (3 pages) ,
- Quick start manual (6 pages) ,
- Hardware user's manual (12 pages)
Subscribe to Our Youtube Channel
Related Manuals for Texas Instruments CC2531
Summary of Contents for Texas Instruments CC2531
- Page 1 CC2531 CC2531 Hardware Hardware CC2531 CC2531 USB USB Hardware Hardware User User User’ ’ ’ ’ s s s s Guide Guide Guide User Guide swru221a swru221a swru221a swru221a...
-
Page 2: Table Of Contents
Table Table Table of of of of Contents Contents Contents Table Contents 1 1 1 1 Introduction Introduction ..........................3 Introduction Introduction ..........................3 ..........................3 ..........................3 2 2 2 2 About About About About this this this this Manual Manual Manual Manual ........................3 ........................3 ........................3 ........................3... -
Page 3: 1 1 1 Introduction Introduction Introduction
This manual covers the CC2531 USB dongle found in the CC2530 Development Kit and the CC2530 ZigBee Development Kit. The manual covers the CC2531 USB Dongle hardware component of a USB development framework. Please refer to [3] for a description of the accompanying USB Firmware Library and application examples. -
Page 4: 3 3 3 Acronyms Acronyms Acronyms
Human Interface Device Integrated Circuit In Circuit Emulator Kilo Byte (1024 byte) Light Emitting Diode LPRF Low Power RF Micro Controller Not connected Radio Frequency Receive System on Chip Texas Instruments Transmit UART Universal Asynchronous Receive Transmit Universal Serial Bus... -
Page 5: 4 4 4 Definitions
USB Dongle Dongle Dongle Dongle The CC2531 USB Dongle is a fully operational USB device that can be plugged into a PC. The dongle has 2 LEDs, two small push-buttons and connector holes that allow connection of external sensors or devices. The dongle also has a connector for programming and debugging of the CC2531 USB controller. - Page 6 System on Chip. A collective term used to refer to Texas Instruments ICS with on-chip MCU and RF transceiver. Used in this document to reference the CC2530 and 2531. In Circuit Emulator. ICE functionality is built into the SmartRF05EB and the CC Debugger...
-
Page 7: Getting Getting Started Started
USB dongle. The CC2531 has a 2 wire debug interface that is used for chip programming and debugging. When connecting this interface to the SmartRF05EB, the CC2531 can be programmed from the Smart RF Flash Programmer software [2] and debugged from IAR Embedded Workbench. - Page 8 The CC2531 can now be programmed with the Smart RF Flash Programmer software. The firmware on the CC2531 can also be debugged using the IAR Embedded Workbench debugger. Please see the “Smart RF Flash Programmer User’s Manual” for more details [2].
-
Page 9: 6 6 6 Using
Interface Interface For custom PCB’s with the CC2531 SoC, it is recommended to include a pin header or test points to allow in-circuit emulation or programming using a SmartRF05EB or other 3rd party programming tools. The USB Dongle can be used as a reference. -
Page 10: 7 7 7 Usb
User Interface Interface Interface The CC2531 USB Dongle has two buttons and two LEDs that can be used to interact with the user. Table 1 shows which CC2531 signals are connected to what IO on the dongle. IO IO IO... - Page 11 5.3 dBi. This means that duty cycling or reduction of output power might be needed to ensure compliance with regulatory limits. Please see [8] for more information about SRD regulations in the 2.4 GHz ISM band. The performance of the antenna of the CC2531 USB Dongle is further described in [9].
-
Page 12: Description
Reference Design Design Design Design and and Schematics Schematics Schematics Schematics Refer to [1] for the schematics of the CC2531 USB Dongle. 9 9 9 9 References References References References CC2530 DK Development Kit User Manual (swru208) Smart RF Flash Programmer...
Need help?
Do you have a question about the CC2531 and is the answer not in the manual?
Questions and answers