Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ruskin EFAMS
Summary of Contents for Ruskin EFAMS
- Page 1 Air Quality Solutions Installation & Maintenance Manual Model: EFAMS Electronic Fan Inlet Air & Temperature Measuring Station with Electronic Controller II-EFAMS-818/Replaces II-EFAMS-316 ALL STATED SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE OR OBLIGATION © Ruskin August 2018...
-
Page 2: Installation Instructions
EFAMS Thermal Dispersion Fan Inlet Airflow Measuring System Installation Instructions ApplICATIonS InSTAllATIon The Ruskin EFAMS Thermal Dispersion Fan Inlet Sensor Airflow Measuring System averages veloc- wArnIng: risk of Electric Shock ity and temperature from fan inlet sensors mounted Disconnect power supply before making on the fan inlet bell, providing accurate, dependable electrical connections. - Page 3 The ruskin EFAMS system includes the following Fan Types for the EFAMS standard or optional components/configurations: The ruskin EFAMS system may be applied to the ElECTronIC ConTrollEr with LCD DISPLAY – following types of fans: Standard roUTEr with MULTIPLEXER – Standard SEnSorS Including SENSOR CABLES - Standard Sensor Cables are always 10 FT (3.05 M)
- Page 4 Figure 4: Fan Inlet Sensor Dimensions, in. (mm) Figure 4: Fan Inlet Sensor Dimensions, in. (mm) RUSKIN EFAMS Thermal Dispersion Airflow Measuring System Installation Instructions RUSKIN EFAMS Thermal Dispersion Airflow Measuring System Installation Instructions RUSKIN EFAMS Thermal Dispersion Airflow Measuring System Installation Instructions...
-
Page 5: Installing The Router
Figure 6: router Dimensions, in. (mm) Figure 6 RUSKIN EFAMS Thermal Dispersion Airflow Measuring System Installation Instructions rUSKIn EFAMS ThErMAl DISpErSIon AIrFlow MEASUrIng SYSTEM InSTAllATIon InSTrUCTIonS... - Page 6 Installing the Ruskin Electronic Controller IMporTAnT: Mount the Electronic Controller within 50 feet of the router. Avoid cable loops or coils. Install the Electronic Controller on an adjacent Shorter cable lengths are better. structural wall, plenum, or ductwork that is isolated from excessive system vibration.
- Page 7 Whenever possible, use a dedicated transformer for each EFAMS System. If you use a dedicated transformer for multiple EFAMS Systems, ensure that the transformer is rated with sufficient capacity for the total load of the connected sensors and other devices.
-
Page 8: Finishing The Installation
When power is applied to the installed electronic fan inlet air measurement station and equipment is properly installed and con- RUSKIN EFAMS Thermal Dispersion Airflow Measuring System Installation Instructions nected INITIAL STARTUP FIELD CALIBRATE is displayed. To complete the setup the fan must be able to run at low, medium and high air flows. - Page 9 To repeat the calibration steps again the field calibration mode can be turned off and then on again to repeat the setup steps using fan speeds and conditions previously established as known air flow values for low, medium and high. rUSKIn EFAMS ThErMAl DISpErSIon AIrFlow MEASUrIng SYSTEM InSTAllATIon InSTrUCTIonS...
-
Page 10: Setup And Adjustments
Pressing ESC while in one of the option menus exits the option menu without saving changes and returns to the Initialization menu. To save changes, press ENTER then press ESC. Figure 10: Installation Menu rUSKIn EFAMS ThErMAl DISpErSIon AIrFlow MEASUrIng SYSTEM InSTAllATIon InSTrUCTIonS... -
Page 11: Reset Settings
This option activates the error indication on the LCD screen. When an error occurs, the temperature ap- pears as a lowercase letter f (degrees Fahrenheit). DOWN ENTER Figure 13: Error Indication Submenu Figure 11: reset Settings Submenu rUSKIn EFAMS ThErMAl DISpErSIon AIrFlow MEASUrIng SYSTEM InSTAllATIon InSTrUCTIonS... - Page 12 BAS wiring and verify the test signal at Electronic Controller with a meter. If test signal at Electronic Controller is not correct, contact factory for additional calibration procedure instructions. rUSKIn EFAMS ThErMAl DISpErSIon AIrFlow MEASUrIng SYSTEM InSTAllATIon InSTrUCTIonS...
-
Page 13: Adjusting The Gain
If a system effect is causing an to access the GAIN adjustment. Use UP and DOWN issue with the EFAMS system, use the GAIN for a cor- to adjust the desired gain value (Range = 0.01 to 99). - Page 14 5,000 FPM (25.4 mps) instead of 10,000 FPM (50.8 mps). Down EnTEr DOWN ENTER AUTO RESET note: Range is 0.0 to 1.0. Factory mA output default= .35 Figure 21: Adjust mA output Filter Value Submenu rUSKIn EFAMS ThErMAl DISpErSIon AIrFlow MEASUrIng SYSTEM InSTAllATIon InSTrUCTIonS...
- Page 15 Figure 22: Auto reset on/oFF Submenu Figure 23: Temperature Display on/oFF Submenu Figure 22: Auto Reset ON/OFF Figure 23: Temperature Display Submenu Figure 22: Auto Reset ON/OFF ON/OFF Submenu Figure 23: Temperature Display Submenu ON/OFF Submenu rUSKIn EFAMS ThErMAl DISpErSIon AIrFlow MEASUrIng SYSTEM InSTAllATIon InSTrUCTIonS...
-
Page 16: Troubleshooting
All rights reserved. The product detailed in this manual is protected by a U.S. patent. Illustrations and product descriptions pub- lished are not binding in detail. In keeping with its policy of continuous improvement, ruskin reserves the right to change or modify designs or specifications of products without notice or obligation.
Need help?
Do you have a question about the EFAMS and is the answer not in the manual?
Questions and answers