Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for KUHN GF 5001 TH
Summary of Contents for KUHN GF 5001 TH
- Page 1 ASSEMBLY / OPERATOR'S MANUAL GF 5001 TH GYROTEDDER N° 95221 A.GB. - 06.2002...
-
Page 2: About Improvements
DEAR OWNER, In buying a KUHN machine you have chosen wisely. Into it have gone years of thought, research and improvements. You will find, as have thousands of owners all over the world, that you have the best that engineering skill and actual field testing can produce. You have purchased a dependable machine, but only by proper care and operation can you expect to receive the performance and long service built into it. - Page 3 CONTENTS Page - 1 -...
-
Page 4: Safety Advice
SAFETY ADVICE DESIGNATED USE OF THE MACHINE GF 5001 TH GF 5001 TH GF 5001 TH - 2 -... -
Page 5: General Safety Recommendations
GENERAL SAFETY RECOMMENDATIONS BASIC PRINCIPLES - 3 -... - Page 6 ATTACHMENT - 4 -...
-
Page 7: Power Take-Off
POWER TAKE-OFF (rotational frequency) Rotational frequency Rotational frequency 540 min - 5 -... -
Page 8: Hydraulic System
HYDRAULIC SYSTEM TIRES - 6 -... -
Page 9: Maintenance
MAINTENANCE - 7 -... - Page 10 SPECIAL SAFETY RECOMMENDATIONS - 8 -...
-
Page 11: Safety Decals
SAFETY DECALS - 9 -... - Page 12 - 10 -...
-
Page 13: Technical Specifications
TECHNICAL SPECIFICATIONS - 11 -... - Page 14 ASSEMBLY INSTRUCTIONS 1. Fitting outside rotor casings and hydraulic cylinders (photo 1) 2. Fitting the wheels (photo 2) ATTENTION 3. Fitting the drawbar and crank handle (photo 3) 4. Fitting the hydraulic hoses (photos 4 and 4 A) 5. Fitting control cords (photo 4 A) - 12 -...
- Page 15 - 13 -...
- Page 16 6. Fitting rear shields and rear parking stand (photos 5 and 6) 7. Fitting triangular reflectors (photo 5) 8. Fitting guards (photos 7 and 7 A) 9. Fitting guard cone and its extension (photo 7 A) 10. Fitting tines and tine arms (fig. 8 and 9) - 14 -...
- Page 17 - 15 -...
-
Page 18: Fitting To The Tractor
ATTACHMENT FITTING TO THE TRACTOR GF 5001 TH PTO SHAFT to the 540 rpm (min ) tractor drive These recommendations and adjustments must be respected to avoid damage or premature wear of the PTO. Never connect the PTO to the 1000 rpm (min ) tractor drive. - Page 19 - 17 -...
-
Page 20: Work Position And Adjustments
WORK POSITION AND ADJUSTMENTS BEFORE CARRYING OUT ANY OPERATION SUCH AS MAINTENANCE OR ADJUST- MENT ON THE MACHINE, STOP THE TRACTOR ENGINE, REMOVE IGNITION KEY AND WAIT UNTIL ALL MOVING PARTS COME TO A COMPLETE STOP BEFORE LEAVING THE TRACTOR. KEEP ALL PERSONS AWAY FROM THE VICINITY OF THE MACHINE BEFORE PIVOTING THE OUTER ROTORS INTO WORK POSITION. - Page 21 - 19 -...
-
Page 22: Operating Speed
OPERATING SPEED First time over Second time over In difficult conditions such as these it is generally advisable to lower the forward speed and increase the PTO speed. OPERATION GF 5001 TH (rotational frequency) (min GF 5001 TH - 20 -... - Page 23 - 21 -...
-
Page 24: Transport Position
PARKING THE MACHINE GF 5001 TH IF THE GF 5001 TH IS TO BE PARKED WHEN IN THE TRANSPORT POSITION, ALWAYS PARK THE MACHINE ON VERY EVEN, LEVEL GROUND. WEDGES MUST ALWAYS BE PLACED UNDER THE TWO CENTRAL WHEELS (photo 24). - Page 25 - 23 -...
- Page 26 LUBRICATION Grease the following points with SHELL RETINAX A Every 100 hours Every 50 hours Once a year Lubricate the following point s with SHELL X 100 or SAE 90 EP OIL : Once a week TO ENSURE TROUBLE FREE OPERATION OF YOUR MACHINE, WE RECOMMEND THE USE OF SHELL LUBRICANTS - 24 -...
- Page 27 - 25 -...
-
Page 28: Optional Equipment
OPTIONAL EQUIPMENT 1) DUPLEX REDUCTION GEARBOX (Kit No 111 6440) GF 5001 TH GF 5001 TH (rotational frequency) (min - 26 -... - Page 29 - 27 -...
-
Page 30: Sound Levels
SOUND LEVELS Sound levels given out by : GF 5001 TH Gyrotedder Sound levels have been measured in accordance with the measuring methods as defined in : HM Agricultural Inspectorate AGRICULTURAL MACHINERY NOISE Legislation and guidance on methods of testing... -
Page 31: Limited Warranty
LIMITED WARRANTY KUHN S.A. THESE CONDITIONS ARE SUBJECT TO THE FOLLOWING EXCEPTIONS : THE CUSTOMER WILL BE RESPONSIBLE FOR AND BEAR THE COSTS OF:... - Page 32 LIMITED WARRANTY IS DEPENDENT UPON THE STRICT OBSERVANCE BY THE PURCHASER OF THE FOLLOWING PROVISIONS : DISCLAIMER OF FURTHER WARRANTY There are no warranties, expressed or implied, except as set forth above. There is no warranty of merchantability. There are no warranties which extend beyond the description of the product contained herein.
- Page 33 - N O T E S -...
- Page 35 This machine complies with the safety requirements of the European machinery directive. The Operator should respect all Health and Safety regulations as well as the Highway Code. For your own safety, use only genuine KUHN spare parts. The manufacturer disclaims all responsibilities due to incorrect use or non-compliance with the...
- Page 36 KUHN parts KUHN S.A. 4 Impasse des Fabriques F - 67706 SAVERNE CEDEX Tél. : + 33 (0) 3 88 01 81 00 - Fax : + 33 (0) 3 88 01 81 03 www.kuhnsa.com - E-mail : info@kuhnsa.com...
Need help?
Do you have a question about the GF 5001 TH and is the answer not in the manual?
Questions and answers