4.5 Entering To The Programming Mode, Changing and Saving Parameter
Main Operation Screen
5 secs
SV
SV
P
P
SET
°C
°C
When SET button is pressed
Note-1: If programming
Programming Mode
Entering Screen
for 5 seconds, "P" led starts to
mode accessing
blink. If programming mode
password is 0,
Press increment
entering password is different
hysteresis screen
button for accessing
from 0, programming mode
is observed instead of
to the password
entering screen
will be
programming screen
observed.
accessing password
SV
SV
P
P
SET
°C
°C
Password Entering
Password Entering
Enter programming mode accessing
Press SET/OK button for
accessing to the parameters
password with increment and decrement
Note-2: Parameters can be observed by pressing SET/OK button in password entering
screen without entering the programming mode entering password. But parameters can
not be changed.
Programming Screen
SV
SV
P
P
SET
°C
°C
Hysteresis Parameter
Hysteresis Parameter Value
Parameter is accessed by pressing
Change the parameter with
increment button. If set button is pressed,
increment and decrement buttons
next parameter is shown.
Programming Screen
SV
SV
P
P
SET
°C
°C
Hysteresis Parameter Value
Hysteresis Parameter
Press Set button for saving
Press Set button for accessing
the parameter value
to the next parameter
If no operation is performed in Programming mode for 20 seconds, device turns to
i
main operation screen automatically
5. Failure Messages in ESM-3712-HC Temperature Controller
Probe defect in analogue inputs. Sensor
ESM - 3712-HC
connection is wrong or there is no sensor
connection.
SV
P
SET
°C
Temperature Controller
6. Ordering Information
All order information of ESM-3712-HC
Ordering Information
Temperature Controller are given on the
A BC D
E
/
FG HI
/
U
V W Z
ESM-3712-HC
table at left. User may form appropriate
(77x35 DIN Size)
0
/
00
/
1
0
0
device configuration from information and
A
Supply Voltage
codes that at the table and convert it to the
V
100...240V
(- %15;+%10) 50/60Hz
ordering codes.
1
V
Z
2
24V
(-%15;+%10) 50/60Hz 24V
(-%15;+%10)
Firstly, supply voltage then other
specifications must be determined. Please
9
Customer
fill the order code blanks according to your
Scale(°C)
BC
Input Type
needs.
05
J, Fe CuNi IEC584.1(ITS90)
0°C
800°C
Please contact us, if your needs are
10 K, NiCr Ni IEC584.1(ITS90)
0°C
999°C
out of the standards.
11 PT 100, IEC751(ITS90)
-50°C
400°C
09
PT 100, IEC751(ITS90)
-19.9°C
99.9°C
12
PTC (Note-1)
-50°C
150°C
15 PTC (Note-1)
-19.9°C
99.9°C
14 PT 1000, IEC751(ITS90)
-50°C
400°C
13
-19.9°C
99.9°C
PT 1000, IEC751(ITS90)
18 NTC (Note-1)
-50°C
100°C
19 NTC (Note-1)
-19.9°C
99.9°C
Note-1 : If input type is selected PTC or NTC (BC = 12, 15, 18, 19 ),
c
V
Temperature sensor is given with the device. For this reason,
Symbol means Vac,
If input type is selected as PTC, sensor type (V = 0,1 or 2) or
Z
If input type is selected as NTC, sensor type (V = 0,3 or 4) must be
Symbol means Vdc,
declared in ordering information.
W
Symbol means Vac/dc
E
FG
Outputs
V
Process Out
Relay Output (10 @250V
A
at resistive load, 1NO)
1
01
V
Alarm Out
Relay Output (5 @250V
A
at resistive load, 1NO)
Z
SSR Driver Output (Max. 24mA,16V
)
Process Out
2 02
Z
Alarm Out
SSR Driver Output (Max. 24mA,16V
)
Temp. Sensor which is given with ESM 3712 HC
V
0
None
PTC-M6L40.K1.5
1
(PTC Air Probe with 1.5 m silicon cable)
2
PTCS-M6L30.K1.5.1/8"
(PTC Liquid Probe with 1.5 m silicon
cable)
NTC-M5L20.K1.5
(NTC Probe, thermoplastic moulded with
3
1.5 m cable for cooling application)
NTC-M6L50.K1.5
( NTC Probe, stainless steel housing with
4
1.5 m cable for cooling application)
9
Customer
Programming Screen
SV
SET
P
SET
°C
Minimum Set Value
Minimum Set Value
Parameter
Change the parameter with
Parameter is accessed by pressing
increment and decrement
increment button. If set button is
pressed, next parameter is shown.
Programming Screen
SV
P
SET
SET
°C
Minimum Set Value
Minimum Set Value Parameteri
Change the parameter with
Press Set button for saving the
increment and decrement
parameter value
buttons
Other Programming mode parameters can be
i
accessed with the same method explained above,
SET
observed and changed.
SET
If no operation is performed in Programming mode for 20 seconds, device turns to
i
main operation screen automatically
13
7. Specifications
Device Type
: Temperature Controller
Housing&Mounting
: 77 mm x 35 mm x 62.5 mm plastic housing for panel
Mounting. Panel cut-out is 71 x 29 mm.
Protection Class
: NEMA 4X (IP65 at front , IP20 at rear).
Weight
: Approximately 0.20 Kg.
Environmental Ratings
: Standard, indoor at an altitude of less than 2000 meters
with none condensing humidity.
o
o
o
Storage / Operating Temperature
: -40 C to +85 C / 0 C to +50 C
Storage / Operating Humidity
: 90 % max. (None condensing)
Installation
: Fixed installation
Overvoltage Category
: II.
Pollution Degree
: II, office or workplace, none conductive pollution
Operating Conditions
: Continuous
V
Supply Voltage and Power
:
100-240 V
(-%15;+%10)
V
24V
(-%15;+%10)
50/60 Hz. 2
Z
24V
(-%15;+%10) 2W
Temperature Sensor Inputs
: NTC, PTC, TC, RTD
NTC Input Type
: NTC (10 k @.25 °C )
W
PTC Input Type
: PTC (1000
W
@.25 °C )
Thermocouple Input Types
: J, K (IEC584.1)(ITS90)
Thermoresistance Input Type
: PT-100, PT-1000 (IEC751)(ITS90)
Accuracy
: ±1% of full scale for thermocouple and thermoresistance
Cold Junction Compensation
: Automatically ± 0.1°C/1°C.
Sensor Break Protection
: Upscale
Sampling Cycle
: 3 samples per second
Control Form
: ON / OFF
Relay Output
: Resistive Load 10 A@250 V
(Electrical Life : 100.000 operation (Full Load)
Optional SSR Output
: Maximum 24 mA,Maximum 16 V
Display
: 14 mm Red 3 digits LED Display
Leds
: SV (Green), OUT (Red), P(Red), Alarm(Red) 3 mm
Approvals
: GOST-R,
8. Other Informations
Manufacturer Information:
Emko Elektronik Sanayi ve Ticaret A.Þ.
Demirtaþ Organize Sanayi Bölgesi Karanfil Sk. No:6 16369 BURSA / TURKEY
Tel : +90 224 261 1900
Fax : +90 224 261 1912
Repair and maintenance service information:
Emko Elektronik Sanayi ve Ticaret A.Þ.
Demirtaþ Organize Sanayi Bölgesi Karanfil Sk. No:6 16369 BURSA / TURKEY
Tel : +90 224 261 1900
Fax : +90 224 261 1912
Thank you very much for your preference to
use Emko Elektronik products, please visit our
web page to download user manual.
Your Technology Partner
www.emkoelektronik.com.tr
15
SV
P
SET
°C
SV
P
SET
°C
ESM-3712-HC(SET + ALARM)
Digital, ON / OFF Temperature Controller
- 3 Digits display
- PTC input or
NTC input or
J Type Thermocouple input or
K Type Thermocouple input or
2-wire PT-100 input or
2-wire PT-1000 input (It must be determined in order)
- Temperature control output and alarm output
- Process and alarm set values boundaries
- Selectable heating or cooling function
- Adjustable temperature offset value
- Relay or SSR driver output
- Operation selection of compressor operates continuously, stops
or operates periodically in case of probe defect
- Compressor protection times
- Password protection for programming section
14
1.3 Installation
c
Before beginning installation of this product, please read the instruction
manual and warnings below carefully.
In package ,
- One piece unit
- Two pieces mounting clamps
- One piece instruction manual
o
A visual inspection of this product for possible damage occured during shipment is
recommended before installation. It is your responsibility to ensure that qualified
mechanical and electrical technicians install this product.
If there is danger of serious accident resulting from a failure or defect in this unit, power
off the system and
separate
the electrical connection of the device from the system.
50/60 Hz. 2
VA
VA
The unit is normally supplied without a power supply switch or a fuse. Use power switch
and fuse as required.
Be sure to use the rated power supply voltage to protect the unit against damage and to
prevent failure.
Keep the power off until all of the wiring is completed so that electric shock and trouble
with the unit can be prevented.
Never attempt to disassemble, modify or repair this unit. Tampering with the unit may
results in malfunction, electric shock or fire.
Do not use the unit in combustible or explosive gaseous atmospheres.
V
During the equipment is putted in hole on the metal panel while mechanical installation
some metal burrs can cause injury on hands, you must be careful.
Z
Montage of the product on a system must be done with it's fixing clamps. Do not do the
montage of the device with inappropriate fixing clamp. Be sure that device will not fall
while doing the montage.
It is your responsibility if this equipment is used in a manner not specified in this
instruction manual.
1.4 Warranty
EMKO Elektronik warrants that the equipment delivered is free from defects in material and
workmanship. This warranty is provided for a period of two years. The warranty period starts from
the delivery date. This warranty is in force if duty and responsibilities which are determined in
warranty document and instruction manual performs by the customer completely.
1.5 Maintenance
Repairs should only be performed by trained and specialized personnel. Cut power to the device
before accessing internal parts.
Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of
these solvents can reduce the mechanical reliability of the device. Use a cloth dampened in ethyl
alcohol or water to clean the external plastic case.
16
1.Preface
ESM-3712-HC series temperature controllers are designed for measuring and controlling
temperature. They can be used in many applications with their On / Off control form, heating and
cooling control form and easy-use properties. Some application fields which they are used are
below:
Application Fields
Glass
Food
Plastic
Petro-Chemistry
Textile, Automative
Machine Production Industries
Etc...
1.1 Operating Conditions
Operating Temperature
Max. Operating Humidity :
Altitude
c
77 x 35 DIN Size
Forbidden Conditions:
Corrosive atmosphere, Explosive atmosphere,
Home applications (The unit is only for industrial applications)
1.2 General Specifications
ESM-3712-HC
Power Supply
Input
Temperature Sensor
Input
Standard
Output-1 (Relay Out)
Output-2 (Relay Out)
Optional
Output-1 (SSR Out)
Output-2 (SSR Out)
Instruction Manual. ENG ESM-3712-HC 01 V04 03/14
2. General Description
2.1 Front View and Dimensions of ESM-3712-HC Temperature Controller
Temperature Controller
77 mm / 3.03 inch
2.2 Panel Cut-Out
3
Applications
Heating
Baking Ovens
Incubators
Storages
Air Conditioning
Etc...
:
0 to 50 °C
90% Rh (non-condensing)
:
Up to 2000 m.
Standard
V
100-240 V
(-%15;+
%10
)
50/60Hz
Optional Supply Input
W -%15;+%10
24 V
(
)
50/60Hz
NTC
PTC
J or K Type TC
2-wire PT 100
2-wire PT 1000
Control Output
Heating or Cooling
Alarm Output
Function
ON/OFF Operation
Control Output
Alarm Output
2
Mounting Clamp
Front Panel
IP65 protection
Panel surface
NEMA 4X
(maximum thickness 15 mm / 0.59 inch)
Maximum 15
mm /
0.59 inch
ESM - 3712-HC
SV
P
SET
°C
58.5 mm / 2.30 inch
4 mm /0.16 inch
110 mm / 4.33 inch (min)
71 mm / 2.79 inch
4
Need help?
Do you have a question about the ESM-3712-HC and is the answer not in the manual?
Questions and answers